|
360 glitchip v1.1 problems (coolrunner 2- xc9500)
|
|
|
tez90
Member
|
22. November 2011 @ 04:45 |
Link to this message
|
|
hi, im using nandpro 20b to dump my nand with a usb device, it all goes well up until its finished and there is no dumps anywhere on my laptop to compare? its like nandpro isnt saving them at all for some reason? anybody know why.
iv tried using 20e but it just says cannot open nand1.bin file for writing.
iv got the nandpro folderin root of c drive and use command
C:\NANDPRO/NANDPRO.EXE USB: -r16 NAND1.BIN
WHY WONT IT SAVE ANYWHERE PEOPLE IM NEARLY THERE WITH THIS ONE! PLEASE HELP ASAP
|
|
Advertisement
|
 |
|
|
|
Gray626
Member
|
22. November 2011 @ 21:41 |
Link to this message
|
|
It might be saving somewhere in your documents. do a search for your file. you will find them if you remember what they are named.
|
|
tez90
Member
|
23. November 2011 @ 04:53 |
Link to this message
|
thanks i got them found, it was because i wasnt running it in administator mode, soon as it was changed they where there.
my problem is when using 360 glitchip v1.1 it connects to my board but doesnt recognise the chip or firmware ect. get message WARNING- TDO SEEMS TO BE STUCK AT 1.
iv tried differnt settings but still the sme, im using a xilinx lpt cable, and powering the chip (xilinx coolrunner 2 xc9500) by the xbox dvd cable pins 5+6 for 3.3 and ground. tested them with multimeter its all good from both endsfor power but chips not detected still, any help here is apreciated so i dont end up wasting £30 i just paid out for the kit. thanks
|
|
foxykay
Junior Member
|
23. November 2011 @ 15:29 |
Link to this message
|
Originally posted by tez90:
thanks i got them found, it was because i wasnt running it in administator mode, soon as it was changed they where there.
my problem is when using 360 glitchip v1.1 it connects to my board but doesnt recognise the chip or firmware ect. get message WARNING- TDO SEEMS TO BE STUCK AT 1.
iv tried differnt settings but still the sme, im using a xilinx lpt cable, and powering the chip (xilinx coolrunner 2 xc9500) by the xbox dvd cable pins 5+6 for 3.3 and ground. tested them with multimeter its all good from both endsfor power but chips not detected still, any help here is apreciated so i dont end up wasting £30 i just paid out for the kit. thanks
I have exactly the same problem with this chip. Never resolved it. Take a look at my post on EMS , its has alot more replies than on here.
Who did you buy it from BTW?
|
|
tez90
Member
|
23. November 2011 @ 15:41 |
Link to this message
|
Originally posted by foxykay:
Originally posted by tez90:
thanks i got them found, it was because i wasnt running it in administator mode, soon as it was changed they where there.
my problem is when using 360 glitchip v1.1 it connects to my board but doesnt recognise the chip or firmware ect. get message WARNING- TDO SEEMS TO BE STUCK AT 1.
iv tried differnt settings but still the sme, im using a xilinx lpt cable, and powering the chip (xilinx coolrunner 2 xc9500) by the xbox dvd cable pins 5+6 for 3.3 and ground. tested them with multimeter its all good from both endsfor power but chips not detected still, any help here is apreciated so i dont end up wasting £30 i just paid out for the kit. thanks
I have exactly the same problem with this chip. Never resolved it. Take a look at my post on EMS , its has alot more replies than on here.
Who did you buy it from BTW?
Originally posted by foxykay:
Originally posted by tez90:
thanks i got them found, it was because i wasnt running it in administator mode, soon as it was changed they where there.
my problem is when using 360 glitchip v1.1 it connects to my board but doesnt recognise the chip or firmware ect. get message WARNING- TDO SEEMS TO BE STUCK AT 1.
iv tried differnt settings but still the sme, im using a xilinx lpt cable, and powering the chip (xilinx coolrunner 2 xc9500) by the xbox dvd cable pins 5+6 for 3.3 and ground. tested them with multimeter its all good from both endsfor power but chips not detected still, any help here is apreciated so i dont end up wasting £30 i just paid out for the kit. thanks
I have exactly the same problem with this chip. Never resolved it. Take a look at my post on EMS , its has alot more replies than on here.
Who did you buy it from BTW?
I got it off ebay with a bundle of usb spi flasher and xilinx lpt cable. I'll check out your post, also my board came blank with only 2 little resistor parts on, iv checked voltage on both ends and got the 3.3v from lpt and to power ths cpld, also checked on points on the board and its lowered to 1.8v. Why's this? Thought it needed 3.3 to power?? Thanks
|
|
foxykay
Junior Member
|
23. November 2011 @ 16:28 |
Link to this message
|
|
This message has been edited since posting. Last time this message was edited on 23. November 2011 @ 16:35
|
|
tez90
Member
|
24. November 2011 @ 03:42 |
Link to this message
|
Yeah it was that guy there definetly must be a problem with this cpld, as we both running into same issues, have you tried to use the xilinx impact or just glitchip? I'm goona try impact tday, I'll let u know how I get on wiv that! Other solution is to flog this and just buy a pre programmed off somebody.
|
|
foxykay
Junior Member
|
24. November 2011 @ 07:08 |
Link to this message
|
|
Wouldnt flog it as its probably faulty and someone else is going to be in the same boat as you. I tried impact as well which didnt work.
This message has been edited since posting. Last time this message was edited on 24. November 2011 @ 07:13
|
|
foxykay
Junior Member
|
24. November 2011 @ 07:17 |
Link to this message
|
|
I have opened a case requesting a partial refund. Ill let you know how I get on
|
|
tez90
Member
|
24. November 2011 @ 13:05 |
Link to this message
|
i messaged him complaing and hereplied with this.
'glitchprogram says tdo seems to be stuck at 1?' Note that glitchprogram is not supporting program the C-Mod board using the Xilinx LPT JTAG programmer and could damage the board.
You should use Xilinx's iMPACT software to program it.
The program you mentioned is supposed to use a normal JTAG cable (not xilinx one) to run in a mode called (x)SVF player to program a svf file on to the chip,
but not a .jed file.
The Xilinx LPT JTAG programmer is supported by iMAPACT and you can program CPLD chips directly without the need to export jed files to svf files.
Here have a read of the of the troubleshooting document I wrote about programming it:
https://sites.google.com/site/rghnandfl...a-c-mod-ngzhang
Yes there are buyers have problem program it but all have been proved to be they are program it the wrong way:
Use a wrong software;
Connection is not good;
doesn't provide external power to pin 20 and pin 21;
doesn't connect the programmer's vcc/gnd to the jtag port;
the external power is not 3.3V or is not stable;
the LPT port setting in the BIOS is wrong;
Sometime the buyer's motherboard is not compatible (maybe can do after change the BIOS setting);
Sometime the buyer's operating system has problem (one buyer programmed ok after switching to Linux).
So have a read of the troubleshooting document if you haven't.
Provide me as much information as you can so I can help you.
Better give some snapshot of iMPACT and your hardware setup.
I believe the board should be fine as we tested everyone before dispatching them.
just an excuse i think!
|
|
foxykay
Junior Member
|
24. November 2011 @ 13:18 |
Link to this message
|
Originally posted by tez90:
i messaged him complaing and hereplied with this.
'glitchprogram says tdo seems to be stuck at 1?' Note that glitchprogram is not supporting program the C-Mod board using the Xilinx LPT JTAG programmer and could damage the board.
You should use Xilinx's iMPACT software to program it.
The program you mentioned is supposed to use a normal JTAG cable (not xilinx one) to run in a mode called (x)SVF player to program a svf file on to the chip,
but not a .jed file.
The Xilinx LPT JTAG programmer is supported by iMAPACT and you can program CPLD chips directly without the need to export jed files to svf files.
Here have a read of the of the troubleshooting document I wrote about programming it:
https://sites.google.com/site/rghnandfl...a-c-mod-ngzhang
Yes there are buyers have problem program it but all have been proved to be they are program it the wrong way:
Use a wrong software;
Connection is not good;
doesn't provide external power to pin 20 and pin 21;
doesn't connect the programmer's vcc/gnd to the jtag port;
the external power is not 3.3V or is not stable;
the LPT port setting in the BIOS is wrong;
Sometime the buyer's motherboard is not compatible (maybe can do after change the BIOS setting);
Sometime the buyer's operating system has problem (one buyer programmed ok after switching to Linux).
So have a read of the troubleshooting document if you haven't.
Provide me as much information as you can so I can help you.
Better give some snapshot of iMPACT and your hardware setup.
I believe the board should be fine as we tested everyone before dispatching them.
just an excuse i think!
Yep, he said the same to me. I build my own cable as well which failed. I used impact before trying the glitchprogram. I'm 100% sure I'm not doing anything wrong either, I have confirmed the 3.3v, I have used the LTP to program a NAND before and tried different computers.
|
|
tez90
Member
|
27. November 2011 @ 04:46 |
Link to this message
|
|
any luck with getting the chip programmed foxykay? also what happened with that partial refund from the ebayer seller?
|
|
foxykay
Junior Member
|
27. November 2011 @ 11:24 |
Link to this message
|
Originally posted by tez90:
any luck with getting the chip programmed foxykay? also what happened with that partial refund from the ebayer seller?
Partial refund has been granted and case closed. I am just waiting till tuesday to buy a pre-programmed one.
|
|
tez90
Member
|
27. November 2011 @ 15:41 |
Link to this message
|
Originally posted by foxykay:
Originally posted by tez90:
any luck with getting the chip programmed foxykay? also what happened with that partial refund from the ebayer seller?
Partial refund has been granted and case closed. I am just waiting till tuesday to buy a pre-programmed one.
what board you got? iv been looking into the x360glitch,they also do them pre progrmmed for all other revisions
http://www.acekardsale.co.uk/product/x3...t-falcon-101193
anybody know if these are any good? look easy to install all instructions available via its own webpage. :)
|
|
foxykay
Junior Member
|
28. November 2011 @ 11:03 |
Link to this message
|
I would stay away considering they are china based and they have a ASA Adjudication on them.
http://www.asa.org.uk/ASA-action/Adjudi...ADJ_161729.aspx
I am paying for mine on Tuesday, I'm paying slightly over the odds for the pre-programmed one I am buying but I know the person who is doing it for me will do it properly and professionally!
|
|
Advertisement
|
|
|
|
tez90
Member
|
3. December 2011 @ 13:02 |
Link to this message
|
|
stayed away from that site as advised lol, i ended up buying x360glitch chip from volumerates already pre-programmed, anybody ever used this site or chip? anygood??
|
