|
ixtreme lt1.9
|
|
|
Jav89
Junior Member
|
20. July 2011 @ 07:26 |
Link to this message
|
which folder to i use as firmware. for example for liteon there is firmware for pre and post liteon? that confuses me. i have a liteon 74850c by the way
|
|
Advertisement
|
 |
|
|
AfterDawn Addict
|
20. July 2011 @ 14:43 |
Link to this message
|
Check your console settings to see what dashboard version you have. Then you'll know whether to use the firmware in the pre or post folder.
|
|
Jav89
Junior Member
|
20. July 2011 @ 16:48 |
Link to this message
|
Originally posted by eebeejay:
Check your console settings to see what dashboard version you have. Then you'll know whether to use the firmware in the pre or post folder.
well i was online the other day and got the latest dashboard. so i presume i use post. What does pre and post mean? pre/post a certain version or something?
|
|
Modking30
AfterDawn Addict
|
20. July 2011 @ 18:08 |
Link to this message
|
|
You can still play online with new dash. It's only a few games that will not boot.
|
|
Jav89
Junior Member
|
20. July 2011 @ 18:47 |
Link to this message
|
Originally posted by Modking30:
You can still play online with new dash. It's only a few games that will not boot.
i kno that, just dont know whether to pick pre or post liteon and why?
|
|
Modking30
AfterDawn Addict
|
20. July 2011 @ 19:28 |
Link to this message
|
Pre is if you don't have the OFW. You need to make sure you have a dump off your FW. If not get one, then you can updatee.
|
|
Jav89
Junior Member
|
21. July 2011 @ 06:19 |
Link to this message
|
ok so I broke my lite on but have all the OFW. im getting a new liteon, would you advise me to use the PRE lite on FW and write that straight to new drive with my key or write the original fw to the new drive and then rewrite the POST FW to the drive. From what youve told me, both shud work but one is shorter than the other
|
|
Modking30
AfterDawn Addict
|
21. July 2011 @ 21:11 |
Link to this message
|
Originally posted by Jav89:
ok so I broke my lite on but have all the OFW. im getting a new liteon, would you advise me to use the PRE lite on FW and write that straight to new drive with my key or write the original fw to the new drive and then rewrite the POST FW to the drive. From what youve told me, both shud work but one is shorter than the other
What do you mean you broke it? They are near impossible to brick unless you plugged in the power the wrong way. If it doesn't eject, resend the erase and reflash. PRE is not needed if you have a good dump. PRE is OFW and won't work without the key. Just use the POST.
|
|
Jav89
Junior Member
|
22. July 2011 @ 04:22 |
Link to this message
|
|
fried PCB. bottom line is Im using a replacement liteon.I have the OFW and key saved on my pc and other places too. If i use a new liteon with 74850c FW will i just use POST?
|
|
gnoby
Member
|
22. July 2011 @ 04:42 |
Link to this message
|
You got the new dashboard, that's what 'post' is referring to in this case. So yes use the firmware in the "LiteOn_Post_13141" folder more specifically "LTPlus-025v1.9.bin"
|
|
Jav89
Junior Member
|
22. July 2011 @ 04:47 |
Link to this message
|
|
thats all i needed to know. Thanks
|
|
harvardja
Member
|
24. July 2011 @ 00:57 |
Link to this message
|
so i just updated my xbox (without flashing stock to my hitachi, i know, dumb), and i can't play any backups on it anymore :(
i had lt 1.1+ on my hitachi.
what should i do?
edit: sh#$ it seems like the new lt 1.9 isn't compatible with the hitachi, so am I screwed?
Hi!
This message has been edited since posting. Last time this message was edited on 24. July 2011 @ 01:02
|
|
Modking30
AfterDawn Addict
|
24. July 2011 @ 08:54 |
Link to this message
|
|
There is no 1.9 for hitachis. Flash back to 1.1 + and it will be fine as long as you have the OFW
|
|
harvardja
Member
|
24. July 2011 @ 14:47 |
Link to this message
|
Originally posted by Modking30:
There is no 1.9 for hitachis. Flash back to 1.1 + and it will be fine as long as you have the OFW
i never put in 1.9. it should still be 1.1+ in there...but it doesn't work. am i screwed if i don't have the original firmware (i assume that's what ofw stands for)
edit: i just downloaded the ofw for hitachis. i'm going to just reflash it with 1.1+ and see what happens.
Hi!
This message has been edited since posting. Last time this message was edited on 24. July 2011 @ 14:53
|
|
Modking30
AfterDawn Addict
|
24. July 2011 @ 15:23 |
Link to this message
|
|
You should always have a backup
|
|
harvardja
Member
|
24. July 2011 @ 16:57 |
Link to this message
|
Originally posted by Modking30:
You should always have a backup
wow i have really bad memory. turns out i have a lite-on, lol. so i can put 1.9 in it.
okay, so i was going to flash it to obw, and then to 1.9, but for some reason when i run jungleflasher, it shows my drive already in "vendor mode."
not sure what to do. i've tried some stuff, but am having no progress.
edit: so apparently this means that i have a "bad flash." also, apparently this happens a lot to people who just screw up their drive. but my case is a little different...right after i updated dash, i plugged in my drive to jungle and it said it was in vendor mode right away, so that's kinda weird.
do i really need ck3 probe 3 to fix it? i only have ck3 probe 2...
any advice would be helpful!
Hi!
This message has been edited since posting. Last time this message was edited on 24. July 2011 @ 17:24
|
|
Modking30
AfterDawn Addict
|
24. July 2011 @ 17:40 |
Link to this message
|
Originally posted by harvardja:
Originally posted by Modking30:
You should always have a backup
wow i have really bad memory. turns out i have a lite-on, lol. so i can put 1.9 in it.
okay, so i was going to flash it to obw, and then to 1.9, but for some reason when i run jungleflasher, it shows my drive already in "vendor mode."
not sure what to do. i've tried some stuff, but am having no progress.
edit: so apparently this means that i have a "bad flash." also, apparently this happens a lot to people who just screw up their drive. but my case is a little different...right after i updated dash, i plugged in my drive to jungle and it said it was in vendor mode right away, so that's kinda weird.
do i really need ck3 probe 3 to fix it? i only have ck3 probe 2...
any advice would be helpful!
Doesn't matter. You said you didn't have the OFW, so you're screwed.
|
|
harvardja
Member
|
24. July 2011 @ 17:51 |
Link to this message
|
Originally posted by Modking30:
Originally posted by harvardja:
Originally posted by Modking30:
You should always have a backup
wow i have really bad memory. turns out i have a lite-on, lol. so i can put 1.9 in it.
okay, so i was going to flash it to obw, and then to 1.9, but for some reason when i run jungleflasher, it shows my drive already in "vendor mode."
not sure what to do. i've tried some stuff, but am having no progress.
edit: so apparently this means that i have a "bad flash." also, apparently this happens a lot to people who just screw up their drive. but my case is a little different...right after i updated dash, i plugged in my drive to jungle and it said it was in vendor mode right away, so that's kinda weird.
do i really need ck3 probe 3 to fix it? i only have ck3 probe 2...
any advice would be helpful!
Doesn't matter. You said you didn't have the OFW, so you're screwed.
i can't use the original firmwares that can be downloaded from the iextreme site?
edit: WAIT I FOUND MY OBW I THINK. i just found a folder on my hard drive where i backed everything up. in the folder i have: dummy.bin, inquiry.bin, key.bin, lite_cfw.bin
god i'm trying to follow the jungleflasher guide...but it says i need either ck3 probe 3 or a pmt probe...and i don't have either. i shouldn't need them though, i've gone this far without them. it mentions a "legacy" method, but that it needs soldering. i've used non-soldering methods for the last couple years...again wtf?
should i consider using an older jungleflasher, with and older guide? the recent ones don't seem relevant to me anymore.
Hi!
This message has been edited since posting. Last time this message was edited on 24. July 2011 @ 18:04
|
|
Modking30
AfterDawn Addict
|
24. July 2011 @ 18:31 |
Link to this message
|
You can try to do it by using the 360 for power, but your computer must have a compatible chipset. 6421 via card is recommended. Or just have someone flash it for you. From what I have read in this thread, I would advise you get someone to help you.
|
|
harvardja
Member
|
24. July 2011 @ 18:37 |
Link to this message
|
i have a ck3 probe 2 that gives the power, and i connect the drive via sata to the 6421 via card in my pc.
i'm always clueless at first whenever i decide to re-flash my 360, because it's always a long period between when i need to. and the methods are always different when i come back. but i've been following the jungler guides with success since ixtreme 1.4.
this recent one is giving me problems because it doesn't really apply to my situation anymore...it heavily employs the use of a PMT probe, or whatever 360probe is. i'm not willing to buy it.
i might just use tried and true methods. i'm thinking of using older jungle guides to refresh my memory on how i did it when lt 1.1 came out.
edit: very specifically, my problem with the latest jungleflasher guide is that when i try to detect my drive within jungleflasher, it shows my drive in "vendor mode," and then i don't know what to do. the guide says i have a bad flash, but then states steps the require a "X360USB Pro." i need info on how to do it with a ck3 pro ver 2 :(
Hi!
This message has been edited since posting. Last time this message was edited on 24. July 2011 @ 18:50
|
|
Modking30
AfterDawn Addict
|
24. July 2011 @ 21:02 |
Link to this message
|
Originally posted by harvardja:
i have a ck3 probe 2 that gives the power, and i connect the drive via sata to the 6421 via card in my pc.
i'm always clueless at first whenever i decide to re-flash my 360, because it's always a long period between when i need to. and the methods are always different when i come back. but i've been following the jungler guides with success since ixtreme 1.4.
this recent one is giving me problems because it doesn't really apply to my situation anymore...it heavily employs the use of a PMT probe, or whatever 360probe is. i'm not willing to buy it.
i might just use tried and true methods. i'm thinking of using older jungle guides to refresh my memory on how i did it when lt 1.1 came out.
edit: very specifically, my problem with the latest jungleflasher guide is that when i try to detect my drive within jungleflasher, it shows my drive in "vendor mode," and then i don't know what to do. the guide says i have a bad flash, but then states steps the require a "X360USB Pro." i need info on how to do it with a ck3 pro ver 2 :(
There are some issues with 1.8.5 so you may want to use JF 1.8.4. Make SURE you have dump of the FW before you send an erase or you will screw yourself. Once you have dump, send the erase to get it into vendor mode, then flash to LT 1.9.
|
|
harvardja
Member
|
24. July 2011 @ 21:14 |
Link to this message
|
Originally posted by Modking30:
Originally posted by harvardja:
i have a ck3 probe 2 that gives the power, and i connect the drive via sata to the 6421 via card in my pc.
i'm always clueless at first whenever i decide to re-flash my 360, because it's always a long period between when i need to. and the methods are always different when i come back. but i've been following the jungler guides with success since ixtreme 1.4.
this recent one is giving me problems because it doesn't really apply to my situation anymore...it heavily employs the use of a PMT probe, or whatever 360probe is. i'm not willing to buy it.
i might just use tried and true methods. i'm thinking of using older jungle guides to refresh my memory on how i did it when lt 1.1 came out.
edit: very specifically, my problem with the latest jungleflasher guide is that when i try to detect my drive within jungleflasher, it shows my drive in "vendor mode," and then i don't know what to do. the guide says i have a bad flash, but then states steps the require a "X360USB Pro." i need info on how to do it with a ck3 pro ver 2 :(
There are some issues with 1.8.5 so you may want to use JF 1.8.4. Make SURE you have dump of the FW before you send an erase or you will screw yourself. Once you have dump, send the erase to get it into vendor mode, then flash to LT 1.9.
damn. i think i've come as close as i can get.
the "obw" i had was actually a firmware of ixtreme 1.6, and it was the earliest firmware i had. i decided to spoof it with lt 1.9, and write onto the drive and see if it worked.
it wrote fine, the drive turns on/opens/closes fine, but it won't read backups :(
i'm guessing it's because i didn't have the original, original non-flashed firmware?
i'm boned aren't i?
thank you for your help, modking30.
|
|
Advertisement
|
|
|
|
dazzee
Suspended due to non-functional email address
|
25. July 2011 @ 02:46 |
Link to this message
|
|
Sorry to state the obvious but yes.
You have the incorrect key
sorry
|
