|
No power
|
|
|
santi1031
Junior Member
|
9. November 2010 @ 17:37 |
Link to this message
|
|
yes the xbox is plug in the light on the brick is yellow but when i plug it to the xbox it turns red and the xbox won't do anything please help
|
|
Advertisement
|
|
|
|
Senior Member
|
9. November 2010 @ 18:52 |
Link to this message
|
|
either the brick is bad or the 360. hard to tell unless you have another brick to try in its place. but you should be plugging it into the 360 first then plug it into the wall/poweroutlet
If you send me questions on Live about modding or anything related i will block you. Dont be an idiot.
|
|
santi1031
Junior Member
|
9. November 2010 @ 19:38 |
Link to this message
|
|
yes second brick did the same
|
Senior Member
|
9. November 2010 @ 19:41 |
Link to this message
|
ok, are you using the same powercord with both bricks? as in the cord that plugs into the brick then the wall. just want to make sure that isnt the problem before we say your 360 is bad
If you send me questions on Live about modding or anything related i will block you. Dont be an idiot.
|
|
santi1031
Junior Member
|
9. November 2010 @ 22:46 |
Link to this message
|
|
it my friend xbox his we thought it was the brick so we try it with my brick and we got the same resort
|
Senior Member
|
9. November 2010 @ 23:16 |
Link to this message
|
|
Sounds like you have a short circuit somewhere in the xbox. Make sure none of the USB connectors are bent/touching metal and if you've ever taken the motherboard out of the chassis make sure none of the metal clips around the ports are folded into the ports
This message has been edited since posting. Last time this message was edited on 9. November 2010 @ 23:17
|
Senior Member
|
10. November 2010 @ 06:28 |
Link to this message
|
|
I second w00ly, I have run into this a couple times as well.
"All drives should be updated to Lite Touch + (LT+) firmware if playing on XBOX live. Samsung drives and pre-78/79 Hitachi drives do not utilize AP 2.5. All other drives are considered to be detectable by Microsoft (YMMV). Make sure all rips are ABGX verified, contain SSv2, and patched AP2.5 (where needed). XGD3 must currently be burned on new drive with PC Burner Max firmware for 100% rip. All modded consoles can be potentially unsafe for use on XBOX live."
|
|
santi1031
Junior Member
|
27. November 2010 @ 22:38 |
Link to this message
|
|
hi i have open it looked around nothing is touching is their a way to know if its the motherboard or what else do you think it mite be
thank you for your time
|
|
Thosmos
Member
|
27. November 2010 @ 23:01 |
Link to this message
|
Originally posted by w00ly:
Sounds like you have a short circuit somewhere in the xbox. Make sure none of the USB connectors are bent/touching metal and if you've ever taken the motherboard out of the chassis make sure none of the metal clips around the ports are folded into the ports
I agree with w00ly. I had one that wouldn't power on -- though the brick stayed amber when plugged in -- no change -- but the USB port had been damaged, and the metal fingers were grounded. Straightened them out so that they weren't touching the sides of the port causing a ground fault, and the machine powered on.
The ports on the front remain unusable, but there is one on the back!
;)
Lite-On 74850, Ben-Q 64930, Hitachi 47DJ, Samsung MS28.
This message has been edited since posting. Last time this message was edited on 27. November 2010 @ 23:06
|
|
Thosmos
Member
|
27. November 2010 @ 23:07 |
Link to this message
|
Originally posted by santi1031:
hi i have open it looked around nothing is touching is their a way to know if its the motherboard or what else do you think it mite be
thank you for your time
Look into the front USB ports, and compare them to your PC...
Lite-On 74850, Ben-Q 64930, Hitachi 47DJ, Samsung MS28.
|
|
Thosmos
Member
|
27. November 2010 @ 23:08 |
Link to this message
|
Originally posted by Thosmos:
Originally posted by w00ly:
Sounds like you have a short circuit somewhere in the xbox. Make sure none of the USB connectors are bent/touching metal and if you've ever taken the motherboard out of the chassis make sure none of the metal clips around the ports are folded into the ports
I agree with w00ly. I had one that wouldn't power on -- though the brick stayed amber when plugged in -- no change -- but the USB port had been damaged, and the metal fingers were grounded. Straightened them out so that they weren't touching the sides of the port causing a ground fault, and the machine powered on.
The ports on the front remain unusable, but there is one on the back!
;)
Did you do a washer fix on this machine for a RROD?
Lite-On 74850, Ben-Q 64930, Hitachi 47DJ, Samsung MS28.
|
|
santi1031
Junior Member
|
27. November 2010 @ 23:33 |
Link to this message
|
|
sorry but what is a washer fix
|
|
Thosmos
Member
|
28. November 2010 @ 00:02 |
Link to this message
|
Originally posted by santi1031:
sorry but what is a washer fix
No worries. It's a fix kit for the red ring, that if you don't do correctly, can cause a ground fault -- and your no power issue. I'd check the USB ports then. That's the easy fix. Two front and one back.
Lite-On 74850, Ben-Q 64930, Hitachi 47DJ, Samsung MS28.
|
|
Advertisement
|
|
|
|
santi1031
Junior Member
|
28. November 2010 @ 13:42 |
Link to this message
|
|
i checked everything and nothing is touching i took the xbox apart just to make sure and nothing happend
|
