|
Quick question on Lizard
|
|
|
snickle
Member
|
25. February 2011 @ 13:10 |
Link to this message
|
I bought a Lizard and it came with everything it was supposed to, there are 2 probes, 2 pogo grabbers etc, but then theres this black connector board with a power switch and what I am assuming is an eject button. Now, it appears as though I need a connectivity kit to hook the other end of this black board to, I recently bought a CK3 probe 2 with a connectivity kit, can I use that one without damaging anything?
|
|
Advertisement
|
|
|
|
|
smiddy911
Newbie
|
25. February 2011 @ 14:42 |
Link to this message
|
Originally posted by snickle:
I bought a Lizard and it came with everything it was supposed to, there are 2 probes, 2 pogo grabbers etc, but then theres this black connector board with a power switch and what I am assuming is an eject button. Now, it appears as though I need a connectivity kit to hook the other end of this black board to, I recently bought a CK3 probe 2 with a connectivity kit, can I use that one without damaging anything?
May I please ask, where did you order from in which they have already started shipping?
This message has been edited since posting. Last time this message was edited on 25. February 2011 @ 15:27
|
|
widowmaka
Member
|
25. February 2011 @ 15:07 |
Link to this message
|
Originally posted by snickle:
I bought a Lizard and it came with everything it was supposed to, there are 2 probes, 2 pogo grabbers etc, but then theres this black connector board with a power switch and what I am assuming is an eject button. Now, it appears as though I need a connectivity kit to hook the other end of this black board to, I recently bought a CK3 probe 2 with a connectivity kit, can I use that one without damaging anything?
yes you can just plug it into your ck3 and your good to go.enjoy.its a nice bit of kit i got mine 1 week ago.hopefully they release hitachi support for it soon
|
|
Modking30
AfterDawn Addict
|
25. February 2011 @ 16:11 |
Link to this message
|
|
You don't need a connectivity kit. You use that switch to connect to the 360 for power.
|
|
snickle
Member
|
25. February 2011 @ 18:15 |
Link to this message
|
Thanks for the replies, I tried using it with the ck3 connectivity kit and the black board flashed blue and turned off, so I guess it canceled it out somehow so I used the 360 power as a source only to find out that the drive is a phillips-benq (now I remember that I spoofed it a long time ago). Will this device spoof the firmware for me or should I go about it the old fashioned way?
Update - well so I went about it using JF and the firmware reads at LT 1.1 is that the latest version?
This message has been edited since posting. Last time this message was edited on 25. February 2011 @ 18:32
|
|
Modking30
AfterDawn Addict
|
25. February 2011 @ 18:59 |
Link to this message
|
|
You can still spoof. Just load up the FW in Lizard toolbox as normal and create the the CFW and flash.
|
|
snickle
Member
|
25. February 2011 @ 19:13 |
Link to this message
|
|
Ok, thanks, but is LT 1.1 the latest version?
|
|
Advertisement
|
|
|
|
Modking30
AfterDawn Addict
|
26. February 2011 @ 10:07 |
Link to this message
|
LT Plus 1.1 is the latest for most drives. LT 1.0 for samsung.
|
