|
think i bricked liteon
|
|
|
monkijin
Member
|
26. November 2010 @ 04:10 |
Link to this message
|
hiya
used jungleflasher many times before with no problems all i did was try and upgrade from lt to lt+ i already have the stock firmware (all be it without calibration data)made my firmware by loading my dummy bin in source and lt+ in target erased the drive and got 0x72 status went to flash the drive and i get unknown status 0x80 for some reason.
it,s a straight forward 7 series liteon and i have ck3 and latest jungle flasher.
normally pissed off
|
|
Advertisement
|
 |
|
|
|
tozadog
Junior Member
|
26. November 2010 @ 04:38 |
Link to this message
|
Originally posted by monkijin:
hiya
used jungleflasher many times before with no problems all i did was try and upgrade from lt to lt+ i already have the stock firmware (all be it without calibration data)made my firmware by loading my dummy bin in source and lt+ in target erased the drive and got 0x72 status went to flash the drive and i get unknown status 0x80 for some reason.
it,s a straight forward 7 series liteon and i have ck3 and latest jungle flasher.
Just click write when you have drive in vendor mode you dont have to do the liteon erase!
|
|
monkijin
Member
|
26. November 2010 @ 12:30 |
Link to this message
|
Originally posted by tozadog:
Originally posted by monkijin:
hiya
used jungleflasher many times before with no problems all i did was try and upgrade from lt to lt+ i already have the stock firmware (all be it without calibration data)made my firmware by loading my dummy bin in source and lt+ in target erased the drive and got 0x72 status went to flash the drive and i get unknown status 0x80 for some reason.
it,s a straight forward 7 series liteon and i have ck3 and latest jungle flasher.
Just click write when you have drive in vendor mode you dont have to do the liteon erase!
i get drive into vendor mode and try and flash but it just keeps doing the same thing i have since flashed a benq and it flashes fine
normally pissed off
This message has been edited since posting. Last time this message was edited on 26. November 2010 @ 12:32
|
|
JLF24
Member
|
26. November 2010 @ 13:11 |
Link to this message
|
Originally posted by monkijin:
Originally posted by tozadog:
Originally posted by monkijin:
hiya
used jungleflasher many times before with no problems all i did was try and upgrade from lt to lt+ i already have the stock firmware (all be it without calibration data)made my firmware by loading my dummy bin in source and lt+ in target erased the drive and got 0x72 status went to flash the drive and i get unknown status 0x80 for some reason.
it,s a straight forward 7 series liteon and i have ck3 and latest jungle flasher.
Just click write when you have drive in vendor mode you dont have to do the liteon erase!
i get drive into vendor mode and try and flash but it just keeps doing the same thing i have since flashed a benq and it flashes fine
If you have a usb thumb drive you can flash it with dosflash.. very easy.. this is how I did mine... I saved the hacked LT+ FW using Jungleflasher then used dosflash to erase and rewrite the new hacked fw.. I went from iXtreme 1.6 to LT+ you should have no problem going from LT to LT+ with the same method since you have your LT FW with the key... good luck
http://www.ixtreme.net/ixtreme-lite-touch-flashing/tutorial-your-liteon-freezes-during-erase-t2522.html
This message has been edited since posting. Last time this message was edited on 26. November 2010 @ 13:15
|
Senior Member
|
26. November 2010 @ 13:38 |
Link to this message
|
Originally posted by JLF24:
Originally posted by monkijin:
Originally posted by tozadog:
Originally posted by monkijin:
hiya
used jungleflasher many times before with no problems all i did was try and upgrade from lt to lt+ i already have the stock firmware (all be it without calibration data)made my firmware by loading my dummy bin in source and lt+ in target erased the drive and got 0x72 status went to flash the drive and i get unknown status 0x80 for some reason.
it,s a straight forward 7 series liteon and i have ck3 and latest jungle flasher.
Just click write when you have drive in vendor mode you dont have to do the liteon erase!
i get drive into vendor mode and try and flash but it just keeps doing the same thing i have since flashed a benq and it flashes fine
If you have a usb thumb drive you can flash it with dosflash.. very easy.. this is how I did mine... I saved the hacked LT+ FW using Jungleflasher then used dosflash to erase and rewrite the new hacked fw.. I went from iXtreme 1.6 to LT+ you should have no problem going from LT to LT+ with the same method since you have your LT FW with the key... good luck
http://www.ixtreme.net/ixtreme-lite-touch-flashing/tutorial-your-liteon-freezes-during-erase-t2522.html
JLF24 You dont need a thumb drive anymore, monkijin just google dosflash32, its really easy to use!!
|
|
monkijin
Member
|
26. November 2010 @ 16:33 |
Link to this message
|
i have tried dosflash and my computer won't see the drive i will have to spoof the benq as liteon this amchine doesn't go online anyway but i deffo think it is knackered i can flash benq and liteon with jungleflasher no problem.
one question i have upgraded to lastest dash and then put the spoofed benq drive in with lt+ firemware will it play the latest games if i don't use agbx or do i have to use agbx everytime.
normally pissed off
|
|
Modking30
AfterDawn Addict
|
26. November 2010 @ 18:58 |
Link to this message
|
Originally posted by tozadog:
Originally posted by monkijin:
hiya
used jungleflasher many times before with no problems all i did was try and upgrade from lt to lt+ i already have the stock firmware (all be it without calibration data)made my firmware by loading my dummy bin in source and lt+ in target erased the drive and got 0x72 status went to flash the drive and i get unknown status 0x80 for some reason.
it,s a straight forward 7 series liteon and i have ck3 and latest jungle flasher.
Just click write when you have drive in vendor mode you dont have to do the liteon erase!
Funny! Last I checked you have to send ERASE to get it into vendor noob....I mean mode.
|
|
Modking30
AfterDawn Addict
|
26. November 2010 @ 18:59 |
Link to this message
|
Originally posted by monkijin:
i have tried dosflash and my computer won't see the drive i will have to spoof the benq as liteon this amchine doesn't go online anyway but i deffo think it is knackered i can flash benq and liteon with jungleflasher no problem.
one question i have upgraded to lastest dash and then put the spoofed benq drive in with lt+ firemware will it play the latest games if i don't use agbx or do i have to use agbx everytime.
Load up JF. load dummy.bin and LTplus. Send erase to get drive in vendor mode. Sometimes this takes a few tries. Just keep hitting send erase and power cycling until you get it. Write the firmware, outro, done.
|
|
monkijin
Member
|
27. November 2010 @ 05:47 |
Link to this message
|
Originally posted by Modking30:
Originally posted by monkijin:
i have tried dosflash and my computer won't see the drive i will have to spoof the benq as liteon this amchine doesn't go online anyway but i deffo think it is knackered i can flash benq and liteon with jungleflasher no problem.
one question i have upgraded to lastest dash and then put the spoofed benq drive in with lt+ firemware will it play the latest games if i don't use agbx or do i have to use agbx everytime.
Load up JF. load dummy.bin and LTplus. Send erase to get drive in vendor mode. Sometimes this takes a few tries. Just keep hitting send erase and power cycling until you get it. Write the firmware, outro, done.
it says 0x72 if i intro device id but as soon as i click write it comes up with invalid status 0x80.
is there anyone in the uk that can flash it for me i am in norfolk area just to make sure it isn't something to do with my pc. i have since flashed a samsung with lt and a benq with lt+ with no problems.
normally pissed off
|
|
Modking30
AfterDawn Addict
|
27. November 2010 @ 15:53 |
Link to this message
|
|
Are you doing a power cyle and reading the fw first?
|
|
monkijin
Member
|
27. November 2010 @ 16:19 |
Link to this message
|
Originally posted by Modking30:
Are you doing a power cyle and reading the fw first?
yeah i turn off and on and no go i think it is dead is there anyway to not spoof the benq but to just put my drive key on the benq firmware bear in mind the console come with the liteon
normally pissed off
|
|
monkijin
Member
|
28. November 2010 @ 16:37 |
Link to this message
|
Originally posted by monkijin:
Originally posted by Modking30:
Are you doing a power cyle and reading the fw first?
yeah i turn off and on and no go i think it is dead is there anyway to not spoof the benq but to just put my drive key on the benq firmware bear in mind the console come with the liteon
i'm having another logic board sent so see wot happens then i thought you weren't able to brick liteon drives
normally pissed off
|
|
Modking30
AfterDawn Addict
|
28. November 2010 @ 21:41 |
Link to this message
|
Originally posted by monkijin:
Originally posted by monkijin:
Originally posted by Modking30:
Are you doing a power cyle and reading the fw first?
yeah i turn off and on and no go i think it is dead is there anyway to not spoof the benq but to just put my drive key on the benq firmware bear in mind the console come with the liteon
i'm having another logic board sent so see wot happens then i thought you weren't able to brick liteon drives
near impossible. I am guessing you just need to keep sending an erase to the drive, it will eventually come up. You are using a via chipset sata card?
|
|
monkijin
Member
|
29. November 2010 @ 13:54 |
Link to this message
|
i have tried so many times using liteon erase but it just will not write the firmware even with 0x72 status as soon as i click the write button a box comes up with invalid status 0x80 but i can flash benq and samsung no problem
normally pissed off
|
|
Modking30
AfterDawn Addict
|
29. November 2010 @ 14:23 |
Link to this message
|
Originally posted by monkijin:
i have tried so many times using liteon erase but it just will not write the firmware even with 0x72 status as soon as i click the write button a box comes up with invalid status 0x80 but i can flash benq and samsung no problem
are you using a via 6421 card?
|
|
monkijin
Member
|
29. November 2010 @ 14:33 |
Link to this message
|
Originally posted by Modking30:
Originally posted by monkijin:
i have tried so many times using liteon erase but it just will not write the firmware even with 0x72 status as soon as i click the write button a box comes up with invalid status 0x80 but i can flash benq and samsung no problem
are you using a via 6421 card?
yeah i have used it since the beginning i moght try my sons pc just incase windows update has done anything worth a try i suppose i,m on 32 bit vista
normally pissed off
|
Senior Member
|
29. November 2010 @ 15:54 |
Link to this message
|
|
i did my 8xxx v1 series lastnight and the first time i sent the liteon erase i power cycled at the wrong time (too early as i was in a rush which isnt good)
this froze my pc so i had to reboot. afterwards i had to send intro button to the drive to get into vendor mode instead of the liteon erase and it worked fine after that.
If you send me questions on Live about modding or anything related i will block you. Dont be an idiot.
|
|
shotgun_jesus
Newbie
|
30. November 2010 @ 12:03 |
Link to this message
|
I had similar issues with a friends Lite-On 7 series. Once I erased it to get it in vendor mode, it wouldn't flash and went to 0x80 status. Couldn't eject it once erased in vendor mode, and the pc kept running slow & locking up. After manually ejecting the tray, I eventually got the drive to be recognized correctly. Restarted the pc and power cycled the drive with tray half closed. Flashed with LT+ and updated to new dash. Everything works fine. Just try to be patient and keep trying. As long as you have the drive key and dummy.bin, you should be fine. Took about an hour of messing with it total. Took all of 10-15 minutes with the BenQ drives I've done.
Good luck.
|
|
Advertisement
|
|
|
|
monkijin
Member
|
13. December 2010 @ 06:02 |
Link to this message
|
Originally posted by stealthdf:
i did my 8xxx v1 series lastnight and the first time i sent the liteon erase i power cycled at the wrong time (too early as i was in a rush which isnt good)
this froze my pc so i had to reboot. afterwards i had to send intro button to the drive to get into vendor mode instead of the liteon erase and it worked fine after that.
cheers everyone sorted it on my sons pc i have found out that after a windows update i had installed drivers for the via card after i deleted the driver file from system 32 folder it now runs fine had been baffled for days with this,bloody windows update
normally pissed off
|
