|
xbox 360 83850c cant be re flashed!
|
|
|
davisamm
Newbie
|
25. May 2010 @ 12:38 |
Link to this message
|
hi
i have a liteon 87350c and its already pre flashed but i cant get it to vendor mode to flash it again with the new LT 1.1 i follow trough the lastest JF tutorial and it no use
im also using the CK3 any ideas? am i doing something wrong?
thanks
|
|
Advertisement
|
 |
|
|
Senior Member
|
25. May 2010 @ 14:15 |
Link to this message
|
|
reason u cant flash with a probe its cause its a 8xx series only 7xxs use probes if your doing this
u need to do more research on what version drive you have and too flash it right,leerage has a quide on here,search
This message has been edited since posting. Last time this message was edited on 25. May 2010 @ 14:16
|
AfterDawn Addict
3 product reviews
|
25. May 2010 @ 14:25 |
Link to this message
|
|
You will need to determine if its the v1 or the v2, there are 2 different versions that are labled the same. Whats the manufacture date of the drive?
|
|
davisamm
Newbie
|
26. May 2010 @ 14:44 |
Link to this message
|
|
may 2009
|
AfterDawn Addict
|
26. May 2010 @ 19:13 |
Link to this message
|
Originally posted by davisamm:
may 2009
I think that's a gray area date-wise. Take the drive apart: Remove the 4 screws to remove the shell, take the 2 tiny screws off of the drive's board. On the other side of the board, are two stickers. Ignore the rectangular sticker. The smaller, square sticker should say: 83850c, 83850c2, or 93450 on it.
|
|
davisamm
Newbie
|
27. May 2010 @ 01:13 |
Link to this message
|
|
ok i ll try that later today
thanks alot for now
|
Senior Member
|
27. May 2010 @ 03:38 |
Link to this message
|
|
may 2009 is v1
june
july
no aug 09 till now are v2's or 9series
|
Senior Member
|
27. May 2010 @ 03:44 |
Link to this message
|
Can you give us some more details about your method of flashing? What is your computer configuration. Have you pulled the other drives out to isolate your flash? Are you using the right chipset? Is the drive detected in jungleflasher? I have you tried dosflash...etc?
"All drives should be updated to Lite Touch + (LT+) firmware if playing on XBOX live. Samsung drives and pre-78/79 Hitachi drives do not utilize AP 2.5. All other drives are considered to be detectable by Microsoft (YMMV). Make sure all rips are ABGX verified, contain SSv2, and patched AP2.5 (where needed). XGD3 must currently be burned on new drive with PC Burner Max firmware for 100% rip. All modded consoles can be potentially unsafe for use on XBOX live."
|
|
davisamm
Newbie
|
27. May 2010 @ 06:54 |
Link to this message
|
sure im doing this on a win 7 machine use a via chipset with JF the latest version and yes JF it detects the drive
the thing is why i cant get it to read the since the drive is already hacked before
|
|
davisamm
Newbie
|
27. May 2010 @ 13:31 |
Link to this message
|
|
hi an update i did as eebeejay said and on the small sticker it states that it is a 83850c-2
|
AfterDawn Addict
3 product reviews
|
27. May 2010 @ 14:40 |
Link to this message
|
Originally posted by davisamm:
hi an update i did as eebeejay said and on the small sticker it states that it is a 83850c-2
You will need to follow the instructions in jungle flasher for the 9 series lite on then as they are the same. LT acts like OFW so it will be the same process as flashing from stock. It required a 22ohm resistor and a 3 way switch
|
|
davisamm
Newbie
|
27. May 2010 @ 15:17 |
Link to this message
|
Originally posted by miketrev:
Originally posted by davisamm:
hi an update i did as eebeejay said and on the small sticker it states that it is a 83850c-2
You will need to follow the instructions in jungle flasher for the 9 series lite on then as they are the same. LT acts like OFW so it will be the same process as flashing from stock. It required a 22ohm resistor and a 3 way switch
does it require soldering because i m not that good
|
Member
|
27. May 2010 @ 18:20 |
Link to this message
|
Originally posted by miketrev:
Originally posted by davisamm:
hi an update i did as eebeejay said and on the small sticker it states that it is a 83850c-2
You will need to follow the instructions in jungle flasher for the 9 series lite on then as they are the same. LT acts like OFW so it will be the same process as flashing from stock. It required a 22ohm resistor and a 3 way switch
if you have the keys you are fine, just load them as source. its a volume 1 and are the simplist liteon to do. dont forget to disable the driver so you ddont freeze up.
|
Senior Member
|
27. May 2010 @ 18:34 |
Link to this message
|
|
wow i never seen a may 09 v-2
|
AfterDawn Addict
3 product reviews
|
28. May 2010 @ 04:27 |
Link to this message
|
Originally posted by infam0us:
wow i never seen a may 09 v-2
me neither, Ive seen a July one though
To get instant assistance with Flashing / JTAG / Homebrew from experts for free! click me (Im not one of the said experts BTW)
Make poverty history, cheaper drugs NOW! |
|
davisamm
Newbie
|
28. May 2010 @ 13:31 |
Link to this message
|
Originally posted by miketrev:
Originally posted by infam0us:
wow i never seen a may 09 v-2
me neither, Ive seen a July one though
yes i know i search trough the internet and no one had ever heard of one made in may
|
|
Advertisement
|
|
|
|
davisamm
Newbie
|
28. May 2010 @ 13:34 |
Link to this message
|
i did it. and this is the story
Ranger_Ri told me to use the ofw but i couldnt find it but instead i found a screenshot of the key before flashing, and i had a dead xbox with a benq drive so what i did i spoofed the benq to make the working xbox recognize it as a liteon drive and i typed in the key from the screenshot and it WORKED !!!!!!
|
