|
euro vox EX1000 SL cant find channels
|
|
|
purpose
Newbie
|
24. August 2009 @ 14:55 |
Link to this message
|
|
euro vox EX1000 SL cant find channels i have flashed it tried both symbol rates and tried both codes for my area can any one help
|
|
Advertisement
|
|
|
|
|
cserpent
Suspended due to non-functional email address
|
24. August 2009 @ 15:16 |
Link to this message
|
|
deep scan should sort it out but no good if you on nthell bud
|
|
purpose
Newbie
|
24. August 2009 @ 15:25 |
Link to this message
|
|
done deep scan no joy
|
|
purpose
Newbie
|
24. August 2009 @ 15:33 |
Link to this message
|
Originally posted by purpose:
done deep scan no joy on vm
|
|
purpose
Newbie
|
24. August 2009 @ 18:10 |
Link to this message
|
|
done all i can someone please help
|
|
malci
Suspended due to non-functional email address
|
24. August 2009 @ 18:48 |
Link to this message
|
Originally posted by purpose:
done all i can someone please help
First of all are you in UK or Auntie Hell in Ireland, if the latter then forget it okay, it will not work. Now if in UK you need to establish the symbol rate for the area you are in 6952 or 6887, if in doubt then try one at a time (or even state your location and you can be provided with it. Next and most importantly "make sure that you have a LIVE cable feed going into the RF IN socket at the rear of your box, if so then press Menu and go across to Config and choose Clear Data, press OK amd enter Pin 0000 OK - now choose Factory Default on your Symbol Rate OK and OK to cofirm and OK again to start scan. It should then pick up the TPs (Transponders) first and then your channels will then start to drop in, make a cup of tea - when finished - wait for saving then exit to Main Menu, Highlight Language Settings and Press OK, 4 option bars will appear, now enter 1968 and 2 more will appear Emulation and Emm Capture, just ensure that Emulation is enabled, now exit out to TV and let it update. (The obvious thing to ensure before you start is that you have a LIVE Cable feed going into the RF IN socket as I have stated up above) if you have the latest firmware and are located in the UK then you should now have everything on your box.
This message has been edited since posting. Last time this message was edited on 24. August 2009 @ 18:51
|
|
purpose
Newbie
|
25. August 2009 @ 07:53 |
Link to this message
|
|
thanks for all the info malci im in the uk in essex my smbol rate is 6887 but iv tried both i have done all that is stated in your message with no results when you say a live cable feed i have internet with vm and connected the cable to the other connection on the box could this be the problem
|
|
malci
Suspended due to non-functional email address
|
25. August 2009 @ 08:41 |
Link to this message
|
|
Yes that is most likely to be your problem okay, it is likely to be disconnected inside the box. Easiest way is to just put a cable splitter on your Internet connection and it will be fine, so you will need a little length of Digi coaxil, 2 cable plugs and a cable splitter. Everything will work off your Internet connection, do not use the other connection.
|
|
purpose
Newbie
|
25. August 2009 @ 09:01 |
Link to this message
|
|
thanks again malci i will get that done soon as possible thanks again
|
|
malci
Suspended due to non-functional email address
|
25. August 2009 @ 11:31 |
Link to this message
|
Originally posted by purpose:
thanks again malci i will get that done soon as possible thanks again
In the meantime why don't you temporarily disconnect your broadband cable and put the EV direct into the b/b connection and tune the box in, you can then get the stuff you need later.
|
|
purpose
Newbie
|
26. August 2009 @ 12:53 |
Link to this message
|
|
thanks sorry to be a pain i tried what you suuggested and im getting only 47 channels all scrambled my smbol rate is 6.952 any suggestions mate
|
|
malci
Suspended due to non-functional email address
|
26. August 2009 @ 17:04 |
Link to this message
|
There are two symbol rates for Essex, Essex 1 N*L ex CW 6.887 and Essex 2 TW 6.952, so try them both but make sure that you do a Factory Default first okay. And I suggest that you click on the link marked Eurovox and follow HiTeck's excellent guide for setup/scanning.
|
|
foresttod
Junior Member
|
30. March 2011 @ 08:31 |
Link to this message
|
|
Hi All
Does anyone know, if I took my upstairs sky box, or main box to another house,
would I still be able to view all my subscribed channels, sky tell me I have to keep
my phone line connected at all time, is this so? And if I disconnect my phone from my Sky box
will Sky know it's disconnected?
thanks
|
AfterDawn Addict
3 product reviews
|
30. March 2011 @ 12:00 |
Link to this message
|
|
yes sky will know if your box is disconnected but you could bring to another house short term only.
|
|
Advertisement
|
|
|
|
ddp
Moderator
|
30. March 2011 @ 23:09 |
Link to this message
|
|
|
