Originally posted by cactikid:

---

yes you have missed 2s/w online updates,try first a factory reset and when done power off at rear,remove coaxial cable and power on see if the box will do a s/w online update.when done rescan for channels and choose correct net id

if you dont keep an eye on updates the box will have problems later.

---

Originally posted by Lisboa67:

---

NOIDENAME
you done scan via direct feed, no splitters or modem/router connected.

Regards your quote above, SCAN do you mean S/W UPDATE? Or Auto search Scan, are you saying to take/turn off the router out when S/W UPDATE/Scan Auto Search or Do you mean Scanning for ID Network?

As in other post i have done Transfer Data from good working box to the one that was playing up, and box is working ok now, have both POWER SEARCH MODE OFF? Please advise of what i should or could do now? Cheers

---

Originally posted by noideame:

---

Originally posted by Lisboa67:

---

NOIDENAME
you done scan via direct feed, no splitters or modem/router connected.

Regards your quote above, SCAN do you mean S/W UPDATE? Or Auto search Scan, are you saying to take/turn off the router out when S/W UPDATE/Scan Auto Search or Do you mean Scanning for ID Network?

As in other post i have done Transfer Data from good working box to the one that was playing up, and box is working ok now, have both POWER SEARCH MODE OFF? Please advise of what i should or could do now? Cheers

---

do a software update first (which you said you have done) while everything connected router/modem. then do the factory reset. then connect your box direct to wall feed, no splitters or routers connected, then scan (auto search)for programmes, but as cactikid has said you need correct net id as vm have changed some, in mine i now have only one option so no hit and miss to find correct one.

---

Originally posted by Lisboa67:

---

Originally posted by noideame:

---

Originally posted by Lisboa67:

---

NOIDENAME
you done scan via direct feed, no splitters or modem/router connected.

Regards your quote above, SCAN do you mean S/W UPDATE? Or Auto search Scan, are you saying to take/turn off the router out when S/W UPDATE/Scan Auto Search or Do you mean Scanning for ID Network?

As in other post i have done Transfer Data from good working box to the one that was playing up, and box is working ok now, have both POWER SEARCH MODE OFF? Please advise of what i should or could do now? Cheers

---

do a software update first (which you said you have done) while everything connected router/modem. then do the factory reset. then connect your box direct to wall feed, no splitters or routers connected, then scan (auto search)for programmes, but as cactikid has said you need correct net id as vm have changed some, in mine i now have only one option so no hit and miss to find correct one.

---

You say after s/w update & factory reset, TO CONNECT WALL FEED (do you mean s/w update and factort rest WITHOUT this connected? Then CONNECT it AFTER? Then DISCONNECT router...turn OFF altogether? Then SCAN/AUTO SEARCH still without Router on when do i turn on router? How do i know what my correct NET ID is? Really getting confused honestly i do have only 2 brain cells!

---

Originally posted by Lisboa67:

---

NOIDEAME....Have quoted your piece below, but have inserted my q's which am unclear of


have everything connected (router/modem)when doing software update, then the factory reset. then disconnect router from the box,(this is the ethernet plug at back of box or do i have to turn router off by the mains?)

THIS IS CONFUSING YOU SAY then connect the box directly to wall feed,(WAS THIS NOT CONNECTED AS YOU STATED ABOVE 'HAVE EVERYTHING CONNECTED'?
then do a scan for programmes, then connect router back to box (if you turned router off let it reboot and wait 1 minute)then try again, if it doesnt work then i presume its your net id, but i dont know what yours is.

---

Originally posted by Lisboa67:

---

Originally posted by Lisboa67:
--------------------------------------------------------------------------------
NOIDEAME....Have quoted your piece below, but have inserted my q's which am unclear of


have everything connected (router/modem)when doing software update, then the factory reset. then disconnect router from the box,(this is the ethernet plug at back of box or do i have to turn router off by the mains?)

THIS IS CONFUSING YOU SAY then connect the box directly to wall feed,(WAS THIS NOT CONNECTED AS YOU STATED ABOVE 'HAVE EVERYTHING CONNECTED'?
then do a scan for programmes, then connect router back to box (if you turned router off let it reboot and wait 1 minute)then try again, if it doesnt work then i presume its your net id, but i dont know what yours is.
--------------------------------------------------------------------------------

1)yes the ethernet plug.
2)with mine i have vm modem connected as well so i need a splitter, so i need to disconnect splitter and connect direct from wall to box.


So a Checklist before i do all this, can you check and amend before i give it a go?


1) So EVERYTHING PLUGGED IN (coaxial cable? ethernet plug?) and do a s/w update and then Factory Default Reset.

2) Then disconnect the Ethernet Plug out of back of box.

3) Keep Main Feed Coaxial Cable Connected to Box as in Q 1)

4) Scan for Channels Auto-Search.

5) Plug Ethernet Plug Back in to box.

6) Power Search Mode ON or OFF?

No need to turn box on/off at the back anytime doing this?

Also another problem i am getting a lot is 'no signal blah blah' coming up watching programs, so am having to pull plug out on router then plug back in? Could this be numerous people using PC's & Laptops in the house, or do i need a new router or ethernet plugs?

---

Originally posted by cactikid:

---

i would have said remove coaxial cable to update box as the update is through the lan port
the reason i mention this is any info can only be taken in by lan as the coaxial cable is unplugged.
are your cables old or new and connection are good and tight.

---

Originally posted by bzqwx2:

---

I know there has been lots of discussion on this thread, but could somebody assist us all.

My KV box has April 2012 software on it but all channels are scrambled except FTA. I have rescanned using right Net ID. Took cable feed out, tried LAN update, nothing been trying now for three days.

Is there nowhere where we can get Nov 2012 bin file for all that cannot do lan update?

I know there has been a couple of updates since april, is that why all non-fta channels are scrambled?

---

Originally posted by e45:

---

Originally posted by bzqwx2:

---

I know there has been lots of discussion on this thread, but could somebody assist us all.

My KV box has April 2012 software on it but all channels are scrambled except FTA. I have rescanned using right Net ID. Took cable feed out, tried LAN update, nothing been trying now for three days.

Is there nowhere where we can get Nov 2012 bin file for all that cannot do lan update?

I know there has been a couple of updates since april, is that why all non-fta channels are scrambled?

---

Check your vermin website there are area problems all day, there is no file available other than what you download from the net via the remote

---

Originally posted by Lisboa67:

---

cactikid

AfterDawn Addict
you mentioned oxford,somebody from that area posted this.
got mine up and running today,
ex c&w
chan 35
freq 682.25
256 quam
hope this will be of help for area, a mate tuned it in for me

think with all this new stuff happening maybe scanning settings changing.

First of all Have Transferred Data again, and working ok, had a look to Manual Search what you have mentioned above but could not change channel it just stuck on no! 1 and can not change it up to 52, same with the frequency not unless there is a different way to change it?

---