|
1.6 no big deal
|
|
|
scottas
Suspended due to non-functional email address
|
30. August 2004 @ 12:03 |
Link to this message
|
|
Just finished the 10th 1.6 mod. All are working fine after days of abuse!!! The lpc rebuild is not bad, the points on the 1.6 mobo are a bit more forgiving than the d0 points on earlier versions. Also firefuckers ava-install is a great tool!! Good menu from disk boot, can re-install dash format small and large hdd, install apps and so forth. Works like slayers but more updated. The m8_16 bios works well but to run Avalaunch you'll need to change avalaunch.xbe to evoxdash.xbe. Easier than modding the bios.
ver 1.0, 1.5 and 1.6 with 200gb hdds & X3. Team Xecuter Pro front panel with LCD Screen (rocks). GC with qoob pro, Team xecuter's iced cube case mod and a BBA.
|
|
Advertisement
|
 |
|
|
|
scottas
Suspended due to non-functional email address
|
30. August 2004 @ 12:06 |
Link to this message
|
|
Note: All mods were done with 2.3 pros and lites. Can't wait for the X3!!!
ver 1.0, 1.5 and 1.6 with 200gb hdds & X3. Team Xecuter Pro front panel with LCD Screen (rocks). GC with qoob pro, Team xecuter's iced cube case mod and a BBA.
|
|
overryde
Newbie
|
21. September 2004 @ 13:30 |
Link to this message
|
|
hey sounds like you know your stuff. i have a v1.6 xbox and looking for a modder to install my xecuter 2.6 mod chip and up grade the hard drive with all thoes goodies... let me know if you are able to do this work and send me an email at mle04a@acu.edu so we can talk. thanks
|
|
rogerklu
Newbie
|
22. September 2004 @ 09:41 |
Link to this message
|
|
I'm not even at that point. How can I tell what version my xbox is? I want to get a mod chip, but I hear that most are not compatible with v1.6. I looked all over my xbox, cant seem to find a version number. Thanks!
|
|
overryde
Newbie
|
22. September 2004 @ 09:46 |
Link to this message
|
|
The best way to find out what version your xbox is, is to open up your xbox and look at the chips it has installed and go to xbox-scene.com and look at there tutorial on how to find your xbox version, there is allso a way to check it by looking at your serial number but that is not 100% positive. and btw, your version number isnt just stamped on your xbox. just to let you know. Thanks
|
Senior Member
|
24. September 2004 @ 20:23 |
Link to this message
|
|
1.6 versions are real easy to spot
one way you can do it without taking your xbox apart , is by the manufacture date , if its manufactured after April 4, 2004 (US) then chances are its a 1.6 (course you have to take factory refurbs into account, ie older boards)
Ive done quite a few 2.3b chips successfully on a 1.6, using 30 awg link wire for the lpt rebuild, Also made a funky multi colored xbox logo for the M8_16 bios , and increased the fan speed using evtools, for bigger and faster hard drives.
The 2.6 chip, you still have to rebuild the LPT, BUT you can now disable your chip and lock the hdd.
and the new LEDS look cool!
note that if youre doing a large hard drive mod on a 1.6, to enable large hdd over 137gb, use evtools.
btw Scottas, 100% success dude:-) but dont it mke your eyes blink!! lol all those pinhead solder tabs!
Im gonna get me a new lighted magnifier lol
hey by the way, xbox-hq installer is AWESOME!
XB360 hitachi xtreme f/ware, chameleon case, whisper & airflow blue led. XBOX w/ 2.6 2x custom "djboogie" bios. PSP 1.50 w/ devhook .52 % 303 f/ware.
This message has been edited since posting. Last time this message was edited on 24. September 2004 @ 20:24
|
|
rogerklu
Newbie
|
24. September 2004 @ 22:45 |
Link to this message
|
|
Thanks a lot guys. Now that I know that I have a 1.6, I can no longer get that Xenium Ice solderless :( Any recommendations on chips that are easy do-it-yourselfs for 1.6?
|
|
overryde
Newbie
|
24. September 2004 @ 23:16 |
Link to this message
|
|
im a noob but have read up alot about the 1.6 mobo and the lpc rebuild and theres not really a chip for the 1.6 that is easy to install, no mater what its going to require soldering, and if you not good with soldergun i wouldnt take the chance of messing up your new xbox, i would do what im doing and take it to a installer around town, so if they screw it up its on them and not on you, pluse most people will do a 1.6 from 35$ to 50$ so not that bad
|
|
rogerklu
Newbie
|
25. September 2004 @ 09:30 |
Link to this message
|
|
Thanks a bunch, so what would you say is a good mod to get for a 1.6?
|
|
overryde
Newbie
|
25. September 2004 @ 11:02 |
Link to this message
|
|
I got me the xecuter 2.6, thats what alot of people told me to get, or the xenium ice. i herd they are about the same. im not really sure tho. good luck
|
|
rogerklu
Newbie
|
25. September 2004 @ 11:47 |
Link to this message
|
|
Overryder,
the xecuter is compatible with the 1.6? I heard that both the xecuter and xenium is incompatible with the 1.6 xbox, or have I been wrongly informed?
|
|
overryde
Newbie
|
25. September 2004 @ 14:44 |
Link to this message
|
|
i think you were wrongly informed becaus i have talked to about 9 installers and they all know i have a 1.6 mobo and said they could do the install with either chip.
|
|
fortoken
Newbie
|
26. September 2004 @ 07:29 |
Link to this message
|
|
Hello i am about to rebuild the LPC on my 1.6, i already soldered in the pin header. if it's soldered can i still rebuild the LPC on it? Also do i need to flash the chip on another XBOX for it to work or can i do a manual install with a disk?
.fortoken.
|
|
fortoken
Newbie
|
26. September 2004 @ 07:51 |
Link to this message
|
|
BEfor i shove my foot in my mouth again. i need help as you can tell i called the lpt an lpc oh man... plz anyone what should i do on my 1.6 what bios do i need and how can i get it. curse you 1.6!!!!!!!
.fortoken.
|
Senior Member
|
26. September 2004 @ 13:57 |
Link to this message
|
Theres only currently one bios for the 1.6 board, thats the m8_16 (make sure you use the 16 version of the m8)
you CAN customise it for big hdd's and logo colours etc, using evtools.
Rogerklu, yea you were misinformed, you can mod with the 1.6 with the xecuter 2.3 and 2.6, the 2.3 however, will remain "lit" as long as the xbox is plugged in (its the whole "power" problem thing)
the 2.6 has been made to compensate for this with an extra red wire.
all 1.6 boards modded with chips HAVE to have the LPT rebuilt, so theresa no solderless way to do it im 'fraid
Cant tell you DIRECTLY where to gt the m8 bios, but get mIRC, search for xbins on irc.
Or get the xboq-hq installer which has the bios on it
XB360 hitachi xtreme f/ware, chameleon case, whisper & airflow blue led. XBOX w/ 2.6 2x custom "djboogie" bios. PSP 1.50 w/ devhook .52 % 303 f/ware.
|
Senior Member
|
26. September 2004 @ 14:02 |
Link to this message
|
|
oh btw, having the pinheader installed wont make a difference to the LPT rebuild, AS LONG as no pins on top are soldered or crossed etc, basicaly the pinheader is a series of pins that stand "straight up" from the holes, the plastic part just holds them in place, so if the pins arent crossed (soldered together anyway) then youre fine:-)
XB360 hitachi xtreme f/ware, chameleon case, whisper & airflow blue led. XBOX w/ 2.6 2x custom "djboogie" bios. PSP 1.50 w/ devhook .52 % 303 f/ware.
This message has been edited since posting. Last time this message was edited on 26. September 2004 @ 14:02
|
|
fortoken
Newbie
|
26. September 2004 @ 18:13 |
Link to this message
|
|
ok cool so if the pinheader is installed then i can still setup the lpc. nice ok so i need a programer. i have m8_16 but i also want to install a 120 gig western digital how would i go about doing that. and can i install the bios with out a programer?
.fortoken.
|
|
scottas
Suspended due to non-functional email address
|
27. September 2004 @ 11:02 |
Link to this message
|
|
Also on the 2.3, there is a way to utilize the switches to be able to turn off chip power. But for the money the X3 is the way to go. Check out team X's site for the latest info.
ver 1.0, 1.5 and 1.6 with 200gb hdds & X3. Team Xecuter Pro front panel with LCD Screen (rocks). GC with qoob pro, Team xecuter's iced cube case mod and a BBA.
|
|
Phillipo
Suspended due to non-functional email address
|
11. October 2004 @ 11:38 |
Link to this message
|
|
HELP ME PLEASE will some one send me m8_16 bios to looserphil@yahoo.com my work has so many blocks so i can d\l from any site HELP please!!!!
|
|
llongtheD
Suspended due to non-functional email address
|
11. October 2004 @ 11:46 |
Link to this message
|
Read djboogie's post in this thread, its the best way to get a hold of that bios. I doubt if anyone will send you that bios, as it is an illeagal bios. There is a guide to using xbins here: http://www.xbox-scene.com/articles/xbins.php
If your fish seems sick, put it back in the water.
|
|
JustFunky
Newbie
|
12. October 2004 @ 23:34 |
Link to this message
|
|
I need some directions for installing the X-3 on a 1.6 mobo and a 1.1 mobo, please email me if you have any advice or helpful directions (no, the X-3 did not come with any directions at all)
webmister2049@msn.com
This message has been edited since posting. Last time this message was edited on 12. October 2004 @ 23:41
|
|
Advertisement
|
|
|
|
llongtheD
Suspended due to non-functional email address
|
13. October 2004 @ 06:12 |
Link to this message
|
If your fish seems sick, put it back in the water.
This message has been edited since posting. Last time this message was edited on 13. October 2004 @ 06:16
|
