Somebody plz help me! I am the biggest noob at modding

Advertise at AfterDawn.com

Link to us!

Private messages

Compose a private message

List of all updated threads

Threads without replies

Search messages

Thursday 31.7.2025 / 18:00

Search AfterDawn Forums:

afterdawn.com > forums > archived forums > xbox - hardware boot discussion > somebody plz help me! i am the biggest noob at modding

Browse by topic

Forums

Somebody plz help me! I am the biggest noob at modding

Jump to:

Posted

Message

and1balla

Suspended due to non-functional email address

14. January 2005 @ 12:49

Link to this message

im a noob and i got my xbox back with the xecuter 2.6 lite.So as a noob i went on tons of websites.alright then i turn the xbox on with the modchip enabled it boots but then restart 3 times then it turns the button you open the tray with flash green and red.I dont know what the problem is.plz help me with everything.

p.s i got it from modchipman.com.Also if you have a yahoo account name maybe i can talk to you about my problems.

[ + quote]

big_g-man

Member

16. January 2005 @ 18:18

Link to this message

sounds like mabe a bad chip install. open up your box and check all the solder points. if he fried your motherboard like i did my first one, you'll have to buy another mother board and hard drive or new xbox. check all the ground screws in the motherboard, too.

[ + quote]

UIX Dash
Xecuter2.0L
Maxtor 120 GB HDD

P4 3.0Ghz
640mb ddr ram
120 gig hdd

corrupt1

Newbie

17. January 2005 @ 13:04

Link to this message

Universal solderless adapter
V1.4 Xbox
Xecuter 2.6 lite
I spent hours trying to get this set-up to work. All I ever got was rebooting and fragging. Then I noticed that the solderless adapter did not have as many pins As the pogo pin adapter that came with my chip. After many failed attempts with the sodlerless, I Then took the wire harness with the three wires red, green, and gray and hooked it into the chip. Then stuck the end of the gray wire into the DO point ontop of the mother board " Took me a minute to get that" then secured it with electrical tape." stick it directly onto the mother board" Use the pogo pin adapter and held pressure on the side of the chip so it leans the same way the arrow is pointing on the chip. I powered the xbox on and shazam!!!!!! Got the flash bios screen. I then secured it that way with some super adhesive tape works great. Solderless without the adapter. When securing the chip leaning like that it almost touches the mother board. This worked really great been that way for a while no probs. Hope this helps someone whos having problems with the solderless adapter or who doesn't know how to solder.

Coreect me if I'm wrong but has anoyone using the Universal solderless adapter gotten this to work? Will post pics soon.

[ + quote]

delphiki

Suspended due to non-functional email address

22. February 2005 @ 11:44

Link to this message

does anyone know which screw holes are the ground screws? bcause i installed my cghip (which turned on) and i just set the mobo in (i dind't screw all screwws in...) and it frag (flash-red-and-green) and there was no picture.....i deciced ot take out modchip (which i did flawlessly) and it still Frag.
i know it could be i fried the mobo..but i am not sure...thanx

[ + quote]

AHAHAHAHAHA

big_g-man

Member

22. February 2005 @ 13:05

Link to this message

thats your problem. you have to screw in every screw in the mobo. it prolly isn't your chip. stick that thing back in and try screwin all the screws.

[ + quote]

UIX Dash
Xecuter2.0L
Maxtor 120 GB HDD

P4 3.0Ghz
640mb ddr ram
120 gig hdd

afterdawn.com > forums > archived forums > xbox - hardware boot discussion > somebody plz help me! i am the biggest noob at modding


		User name	Password

		Not registered yet? Register here. Lost your password? Click here.