Mobile/PDA About Us Advertise here
User User name Password  
  Not registered yet? Register here.
Lost your password? Click here. 		 
  Home   News   Guides   Downloads   Glossary   Hardware   Profiles   Forums   v4  
 Advertise at AfterDawn.com     Link to us!     Private messages     Compose a private message     List of all updated threads     Threads without replies     Search messages
Thursday 31.7.2025 / 18:25
Search AfterDawn Forums:        In English   Suomeksi   På svenska
afterdawn.com > forums > archived forums > xbox - hardware boot discussion > installed spider chip 1.1, terrible fit and non-working
Show topics
 
Forums
Forums
Installed spider chip 1.1, terrible fit and non-working
  Jump to:
 
Posted Message
jambo1987
Newbie
_ 		17. January 2005 @ 09:00 _ Link to this message    Send private message to this user   
Hi there everyone,
I've recently purchased one of those ultra shoddy spider 1.1 chips.
I did the test to see which version xbox i own going by the graphics chip idea i had the focus chip (ver. 1.4-1.5) so i clipped all the wires off the spider chip apart from the D wire and then attempted to screw the chip onto the motherboard.
Due to the terrible build of the chip once screwed in the chip is completley out of range of the lpc section so i had to blue-tak the chip to the board and solder a power cable to the chip ( no worries tho that part works fine ), i then inserted the D wire to the D0 hole then tested it out, the xbox booted up as normal. i then thaught that this shoddy excuse for non-solder job was the problem so i soldered a cable to the d0 point on the back of the mother board and then onto the chip, the same thing happenes yet again (xbox boots up as normal, no spider chip interface).

My only thoughts were that the xbox version identifier method was incorrect and that i have a version 1.6 xbox .

any comments/suggestions would be very much appreciated, thanks alot
[ + quote]

This message has been edited since posting. Last time this message was edited on 17. January 2005 @ 09:06
Advertisement
_ 		__
jambo1987
Newbie
_ 		18. January 2005 @ 02:02 _ Link to this message    Send private message to this user   
arnt you lot a helpful bunch :P
[ + quote]
focker123
Newbie
_ 		19. January 2005 @ 09:12 _ Link to this message    Send private message to this user   
Spiderchip changed the D and E wire on the 1.1 chip. You need to solder a wire to the E point on the chip and use it instead of D. Also make sure all the pogo pins are touching. The two fartherest away from the screw will lift up on you.
[ + quote]
jambo1987
Newbie
_ 		23. January 2005 @ 03:52 _ Link to this message    Send private message to this user   
thanks alot ill give it a go now and post my results, fingers crossed:)
[ + quote]
Advertisement
_ 		__
 
_
HeLLSaTaN
Newbie
_ 		27. January 2005 @ 06:56 _ Link to this message    Send private message to this user   
hey i got the problem where the 2 pins dont sit right... how do u fix that? how do i get them 2 sit on the lpc
[ + quote]
afterdawn.com > forums > archived forums > xbox - hardware boot discussion > installed spider chip 1.1, terrible fit and non-working
 

Digital video: AfterDawn.com | AfterDawn Forums
Music: MP3Lizard.com
Gaming: Blasteroids.com | Blasteroids Forums | Compare game prices
Software: Software downloads
Blogs: User profile pages
RSS feeds: AfterDawn.com News | Software updates | AfterDawn Forums
International: AfterDawn in Finnish | AfterDawn in Swedish | AfterDawn in Norwegian | download.fi
Navigate: Search | Site map
About us: About AfterDawn Ltd | Advertise on our sites | Rules, Restrictions, Legal disclaimer & Privacy policy
Contact us: Send feedback | Contact our media sales team
 
  © 1999-2025 by AfterDawn Ltd.

  IDG TechNetwork