|
XBIT and 1.6 xbox
|
|
|
bigniggy
Junior Member
|
29. January 2005 @ 21:18 |
Link to this message
|
|
Hey, I've looked around and I cant find the directions anywhere for installing the X.B.I.T. on the 1.6 xbox. Mod-chip.com has a tutorial but its not for 1.6's, just up through 1.5 Any help is appreciated if anyone knows where I can find them?? Also, am I going to HAVE to solder?
Thanks guys, "you make the world go round!"
|
|
Advertisement
|
 |
|
|
|
sjchu
Member
|
30. January 2005 @ 08:57 |
Link to this message
|
|
Yes, You have to solder. For a v1.6 xbox, you need to solder to restore the LPC for the xbit to work. The easiest way is to buy a LPC rebuild board and solder those five points on the back of your motherboard. After that, installing xbit on thev1.6 is pretty much the same as installing it on a v1.5 xbox.
Crystal Limited Edition (v1.6)
Maxtor 250G HD
EvoX m8_16 Xecuter 3
EvoX 3935
XBMC 1.1.0
|
|
bigniggy
Junior Member
|
30. January 2005 @ 15:52 |
Link to this message
|
|
I dont get what your saying I have to solder. The LPC points are already open...?
Also, could I just put this in my xbox 1.0 and put my SOLDERLESS CHAMELEON into his instead?
This message has been edited since posting. Last time this message was edited on 30. January 2005 @ 18:21
|
|
sjchu
Member
|
31. January 2005 @ 16:10 |
Link to this message
|
|
On a v1.6, the LPC port is not connected like previous versions. You have to solder to rebuild the LPC port. So, yes, you have to solder to rebuild the LPC port. Unless you use some chip that does not require LPC port rebuild.
Crystal Limited Edition (v1.6)
Maxtor 250G HD
EvoX m8_16 Xecuter 3
EvoX 3935
XBMC 1.1.0
|
|
fedaykin
Member
|
31. January 2005 @ 19:48 |
Link to this message
|
|
This message has been edited since posting. Last time this message was edited on 2. February 2005 @ 19:41
|
|
sjchu
Member
|
1. February 2005 @ 15:38 |
Link to this message
|
|
That is a surprising news. Has anyone seen a solderless adapter for 1.6 xbox? I saw one from Xenium but it's not released yet.
Crystal Limited Edition (v1.6)
Maxtor 250G HD
EvoX m8_16 Xecuter 3
EvoX 3935
XBMC 1.1.0
|
|
satman69
Newbie
|
4. February 2005 @ 02:04 |
Link to this message
|
|
just installed the xbit on my 1.6 and no there is no solderless chip for the 1.6 yet.
|
|
boscoroll
Newbie
|
29. March 2005 @ 07:03 |
Link to this message
|
|
any way you could post a site with directions on how to install the adapter i can not seem to find them anywhere
|
|
satman69
Newbie
|
29. March 2005 @ 19:25 |
Link to this message
|
|
boscoroll, I can e-mail you the pics on how to install the adapter if you need them. I also have pics of the LPC rebuild, which you must do also. If you do find the pics on the adapter install, 2 of the wires need to be switched, or it won't work. Took me awhile to figure that out, cause the pics on the DMS X-bit website were wrong, and haven't been corrected.
|
|
jedigovna
Newbie
|
16. April 2005 @ 22:09 |
Link to this message
|
|
satman69 i sent you an IM, would like to get those pics if possible.
Thanks
Yeah, Whatever....
|
|
Viper183
Newbie
|
30. April 2005 @ 18:54 |
Link to this message
|
|
Yeah i sent u a PM too..i would also like pics ;) im confused !!
|
|
ecamero
Suspended due to non-functional email address
|
15. May 2005 @ 04:04 |
Link to this message
|
|
can u send me it too satman69?
|
|
Advertisement
|
|
|
|
ecamero
Suspended due to non-functional email address
|
15. May 2005 @ 04:12 |
Link to this message
|
|
hey how did u di this " adapter install, 2 of the wires need to be switched, or it won't work. Took me awhile to figure that out," can u tell mw which
|
