User User name Password  
   
Monday 23.12.2024 / 15:13
Search AfterDawn Forums:        In English   Suomeksi   På svenska
afterdawn.com > forums > archived forums > xbox - hardware mods > my box is frag
Show topics
 
Forums
Forums
My box is FRAG
  Jump to:
 
Posted Message
delphiki
Suspended due to non-functional email address
_
19. February 2005 @ 06:02 _ Link to this message    Send private message to this user   
i installed my xecuter 3 CE wth the solderless install....i turned it on and it was Frag(flashing red and green). So i immediately checked all of the soldering points...they were great...so i checked the D0 point...it was fine....and then i took out the solderless install and the chip(xcept for the soldered objects.) and it still didn't boot up.....anybody know what the problem is????

AHAHAHAHAHA
Advertisement
_
__
delphiki
Suspended due to non-functional email address
_
19. February 2005 @ 06:02 _ Link to this message    Send private message to this user   
i installed my xecuter 3 CE wth the solderless install....i turned it on and it was Frag(flashing red and green). So i immediately checked all of the soldering points...they were great...so i checked the D0 point...it was fine....and then i took out the solderless install and the chip(xcept for the soldered objects.) and it still didn't boot up.....anybody know what the problem is????

AHAHAHAHAHA
delphiki
Suspended due to non-functional email address
_
19. February 2005 @ 06:02 _ Link to this message    Send private message to this user   
i installed my xecuter 3 CE wth the solderless install....i turned it on and it was Frag(flashing red and green). So i immediately checked all of the soldering points...they were great...so i checked the D0 point...it was fine....and then i took out the solderless install and the chip(xcept for the soldered objects.) and it still didn't boot up.....anybody know what the problem is????

AHAHAHAHAHA
big_g-man
Member
_
22. February 2005 @ 16:08 _ Link to this message    Send private message to this user   
maybe you held your soldering iron on there too long. i did that and had to buy a whole new xbox.

UIX Dash
Xecuter2.0L
Maxtor 120 GB HDD

P4 3.0Ghz
640mb ddr ram
120 gig hdd
Macdawgg
Member
_
26. February 2005 @ 05:12 _ Link to this message    Send private message to this user   
Well I wouldn't throw your box out just yet-seems like you make have burned one of your traces on the motherboard-if your not an experinced solderer then check out this site-they can repair your box.-http://www.llamma.com/
fubby16
Newbie
_
2. March 2005 @ 10:00 _ Link to this message    Send private message to this user   
Llamma has some of the best customer service out there. They will actually trade you a working Xbox for a non-working Xbox for like $100, at least that way you can save $50. While you're at it, have them install the mod chip for another $49. They will flash it with Linux Cromwell and you're off for network flashing. I've done buisiness with them a lot and all of their products are top notch, so don't worry about not getting a good Xbox in return.
sjchu
Member
_
2. March 2005 @ 17:03 _ Link to this message    Send private message to this user   
The going rate on ebay right now is around $70 plus shipping for a working xbox motherboard with matching hdd combo. Pick the seller with good rating reputation and you will be fine. eBay sellers are usually very careful to avoid getting negative feedbacks. Stay away from seller with low number in ratings to avoid hit-and-run sellers.

Crystal Limited Edition (v1.6)
Maxtor 250G HD
EvoX m8_16 Xecuter 3
EvoX 3935
XBMC 1.1.0
fubby16
Newbie
_
3. March 2005 @ 05:44 _ Link to this message    Send private message to this user   
I dunno' man, I've gotten screwed on ebay a lot with Xbox stuff. Plus the only reason everyone gets good feedback there is because if you give bad feedback, you're gonna' get bad feedback. If you get bad feedback you hafta' pay $20 just to have a hope that you'll get it taken off. Llamma sells a Motherboard and matching Hard drive for $70 and you know it's from a reputable place.
gsuscrazy
Member
_
4. March 2005 @ 21:11 _ Link to this message    Send private message to this user   
he wouldnt need the matching hdd would he? if he mods his system with a new hdd...?

I remember when dinosaurs roamed the land
I remember when thinkin the earth is flat was cool...
but most of all...i remember when the Apple ruled the schools...GO NUMBER MUNCHERS!!!
sjchu
Member
_
5. March 2005 @ 11:19 _ Link to this message    Send private message to this user   
With a modchip, no, don't need a matching hdd. But, on ebay, no one can sell a motherboard without a matching hdd and claim that it is in working condition. Without a matching hdd, the motherboard only boots to error screen, so it's technically in a non-working condition.


Crystal Limited Edition (v1.6)
Maxtor 250G HD
EvoX m8_16 Xecuter 3
EvoX 3935
XBMC 1.1.0
Advertisement
_
__
 
_
fubby16
Newbie
_
7. March 2005 @ 05:54 _ Link to this message    Send private message to this user   
He could contact Llamma and they would most likely sell him just a motherboard. I dunno' what kind of discount that would leave him at but they run through so many Xboxs they probably have just a motherboard laying around that works.
afterdawn.com > forums > archived forums > xbox - hardware mods > my box is frag
 

Digital video: AfterDawn.com | AfterDawn Forums
Music: MP3Lizard.com
Gaming: Blasteroids.com | Blasteroids Forums | Compare game prices
Software: Software downloads
Blogs: User profile pages
RSS feeds: AfterDawn.com News | Software updates | AfterDawn Forums
International: AfterDawn in Finnish | AfterDawn in Swedish | AfterDawn in Norwegian | download.fi
Navigate: Search | Site map
About us: About AfterDawn Ltd | Advertise on our sites | Rules, Restrictions, Legal disclaimer & Privacy policy
Contact us: Send feedback | Contact our media sales team
 
  © 1999-2024 by AfterDawn Ltd.

  IDG TechNetwork