|
Slim Tool from Modchip.com
|
|
|
donze
Newbie
|
19. June 2005 @ 08:33 |
Link to this message
|
|
Hi guys, I bought the slim tool and swap disks from www.modchip.com the other day and finally (with difficulty) managed to get all three bits installed into my new slimline PS2. The problem is, it doesn't work! the disks will not spin when the lid is open and therefore the swap disks are useless. Has anyone else had this problem? Does anyone know whats went wrong?
|
|
Advertisement
|
|
|
|
|
Mump
Suspended due to non-functional email address
|
19. June 2005 @ 09:42 |
Link to this message
|
|
Make sure tool c (at the back) is pushed all the way down. I had to keep mine down with a little bit of tape.
|
|
berty642
Member
|
19. June 2005 @ 10:51 |
Link to this message
|
hi that tool can be hard to install right, the easiest way is to open the console and tape that sensor down you can find pics here http://www.jspot.net/ps2.htm
Hope this helps
|
|
PimpDawg
Suspended due to non-functional email address
|
19. June 2005 @ 20:02 |
Link to this message
|
|
You could always just get a flip top case so you don't have to worry about that stupid slide card crap.
Proud member of the Afterdawn forums! |
|
tony72
Newbie
|
21. June 2005 @ 07:03 |
Link to this message
|
|
Hi,
I got the same problem. I bought the slim kit pro from modchip.com.
But it doesn't work after the tool installed.
Is there anyone can help me to sort it out, please.
Many thanks
|
|
berty642
Member
|
21. June 2005 @ 08:31 |
Link to this message
|
|
Hi Tony
i posted a link in an earlier reply go there and follow the steps it is pretty easy
|
|
tony72
Newbie
|
24. June 2005 @ 04:41 |
Link to this message
|
|
Thanks for all of your help.
My ps2 with slim pro kit and Swap magic is working fine now.
I did't open the ps2 and put piece of tape on the sensor.
I just put the tool C all the way down,until I can't see it.
Thanks again
|
|
karlai
Junior Member
|
24. June 2005 @ 21:59 |
Link to this message
|
|
Push part b and c :D and the cd will spin opened
PSYCHEDELIC-TRANCE,TRANCE,HOUSE,TECHNO,DANCE:D
|
|
karlai
Junior Member
|
24. June 2005 @ 21:59 |
Link to this message
|
|
Part A and C sorry Not b and C
PSYCHEDELIC-TRANCE,TRANCE,HOUSE,TECHNO,DANCE:D
|
|
sty55555
Junior Member
|
25. June 2005 @ 12:18 |
Link to this message
|
|
is it true that the lid of the ps2 slim will close all the way down normally on both sides...like completely flat opposed to the original slim tool?...I'm assuming that you guys/girls purchased the slimkit pro.
|
|
snake2005
Suspended due to non-functional email address
|
28. June 2005 @ 21:41 |
Link to this message
|
|
why dosent modchip.com give instuctions for installation ?
This message has been edited since posting. Last time this message was edited on 28. June 2005 @ 21:42
|
|
mattie69
Newbie
|
6. July 2005 @ 04:10 |
Link to this message
|
|
after all day searching i cannot find a pic of how to install my slim kit pro into my slimline ps2...does anyone have a pic of it or know where one is on the net...parts A and B have been no dramas but part C i cant figure out...does it go down in between the 2 hinge bits or on the side of it or what?
should i just give up and tape the sensor down?
This message has been edited since posting. Last time this message was edited on 6. July 2005 @ 04:11
|
|
Advertisement
|
|
|
|
PimpDawg
Suspended due to non-functional email address
|
6. July 2005 @ 05:55 |
Link to this message
|
Proud member of the Afterdawn forums!
|
