|
EclPRO Error
|
|
|
TomBrookl
Junior Member
|
2. September 2005 @ 16:56 |
Link to this message
|
|
1st time use and user.
RB ran for 4min 30seconds then stopped and window entitled EclPRO popped up.
It said:
EclPRO v0.42beta
An Ecl Loader for Canopus Procoder
Written by Robot1 - 2004/2005
|
|
Advertisement
|
|
|
|
|
TomBrookl
Junior Member
|
2. September 2005 @ 16:56 |
Link to this message
|
|
1st time use and user.
RB ran for 4min 30seconds then stopped and window entitled EclPRO popped up.
It said:
EclPRO v0.42beta
An Ecl Loader for Canopus Procoder
Written by Robot1 - 2004/2005
|
|
TomBrookl
Junior Member
|
2. September 2005 @ 17:07 |
Link to this message
|
|
Opps - double post above.
I think I'm supposed to be using HCEnc. I didn't buy Procorder.
TomBrooklyn
|
|
TomBrookl
Junior Member
|
2. September 2005 @ 17:11 |
Link to this message
|
|
I found that ProCorder was checked under Mode. I changed it to HC Mode and am trying again.
TomBrooklyn
|
|
TomBrookl
Junior Member
|
2. September 2005 @ 17:26 |
Link to this message
|
|
Now it made it to Overall Progress of 0.8% but it stopped again.
TomBrooklyn
|
|
TomBrookl
Junior Member
|
2. September 2005 @ 17:28 |
Link to this message
|
|
I clicked abort and Overall Progress flashed at 5.6% and then it aborted. Could it be that it was working but not showing any progress on the Overall Progress bar? Nothing had showed in the Program Status window for 15 minutes.
TomBrooklyn
|
|
UncasMS
Member
|
2. September 2005 @ 22:56 |
Link to this message
|
eclpro just like eclcce must be linked to the "encoder.exe"
i.e. when run for the first time you will have to browse for either procoder or CCE EXE and specify that exe in order for eclpro/eclcce to run properly
|
|
TomBrookl
Junior Member
|
3. September 2005 @ 03:14 |
Link to this message
|
Hi Uncas.
I don't know what eclpro is.
I don't know what eclcce is.
I don't know what encoder.exe is, nor am I sure how I would go about linking to it.
I do know that if I clicked on the little folder icons in General Setup (under Options/Setup), paths to various files filled into the space automatically. Therefore, I clicked on the little folders and hoped for the best.
If I understood your Guide so far, both CCE and Procorder must be purchased. I didn't purchase them, so I don't think I have them.
After posting the OP, I realized I should check Mode and I found "Procorder" clicked under there. I realized this was probably a mistake and I clicked HC Mode. If I'm not mistaken, this is the free encoder which is included.
I think this worked because I ran RB again but let it run overnight and it completed.
I found a new file on my hard drive with the name of the disk I am backing up. When I clicked on it, my Roxio software opened up ready to burn. But I closed that and opened Dec*ter and am burning a disk now with that. I think it's going to work. I'll post again when it's done. :)
TomBrooklyn
|
|
TomBrookl
Junior Member
|
3. September 2005 @ 04:48 |
Link to this message
|
|
Hi,
Backup is good. The solution seems to be changing Mode from Procorder to HC. Backup looks great. Thanks. -Tom
TomBrooklyn
|
|
UncasMS
Member
|
3. September 2005 @ 07:18 |
Link to this message
|
hi tom,
good to hear everything went fine in the end
Quote:
If I understood your Guide so far, both CCE and Procorder must be purchased. I didn't purchase them, so I don't think I have them.
that's correct
one can use CCE or procoder if one wanted to
in that case one would have to......
in your case selectiong HC is absolutely fine and hc is a very good freeware encoder
i tested the lastest version 016 last night
in case anyone is interested, go here:
http://forum.digital-digest.com/showthread.php?t=54761
|
|
Advertisement
|
|
|
|
MovieDud
Suspended due to non-functional email address
|
3. September 2005 @ 07:42 |
Link to this message
|
@tombrookl, I'm very glad you figured it out. Rebuilder is my favorite prog. I usually use it in batch mode for 3-4 projects to be completed throughout the night. I use CCE Basic ($60.00) encoder and it is awe-some, but I never hesitated in using HC Hanks or even QuEnc (slower but nice!) when I first beagn using the program. You will really like the quality even when compression gets down to 45% & 50%. have a great day!
MovieDud
|
