|
ps2 slimline red but no green.
|
|
|
chodelord
Newbie
|
10. November 2005 @ 00:16 |
Link to this message
|
|
i recently pulled my ps2 slimeline v12 apart i only took the plastic top off my ps2.
but when i put it back together the red light comes on but when i press power no green..
i checked the ribbons they seem fine although a tiny little metal rectangle peice was on the ground with the corners cut off it.
This message has been edited since posting. Last time this message was edited on 10. November 2005 @ 00:19
|
|
Advertisement
|
|
|
|
|
waleedwc
Senior Member
|
11. November 2005 @ 09:40 |
Link to this message
|
|
The metal piece is for the vertical stand screw that goes in at the bottom of the PS2 when you stand it up, why did you open the the console for no reason, these things cause trouble man, try to avoid the urge to look inside, but anyway, leave the cover of the ps2 of and press the power button using your finger and see what happens, dont touch the PCB though, if you short something and blow it up it isnt my fault mate.
|
|
chodelord
Newbie
|
11. November 2005 @ 17:05 |
Link to this message
|
|
i was putting in magic switch pro and one of the peices fell down inside the ps2 so i had to get it out... looks like the power button has fallen out
|
|
waleedwc
Senior Member
|
12. November 2005 @ 01:00 |
Link to this message
|
|
Sorry, but how can the power button fall out, if the red light was still coming on, or are you saying the power button is broken?
|
|
chodelord
Newbie
|
12. November 2005 @ 03:54 |
Link to this message
|
i've been turning it on by rubbing a paper clip accross the 2 metal conductors it turns it on but a real pain.
This message has been edited since posting. Last time this message was edited on 12. November 2005 @ 03:55
|
|
waleedwc
Senior Member
|
12. November 2005 @ 03:59 |
Link to this message
|
|
Oh i see, so what you should do is try to put the loose piece back in, if it doesnt stick back in then you will have to buy a replacement, its odd you know, how did it fall out, never seen that happen before, you sure you didnt force it out or something buy mistake.
|
|
2nd2one
Newbie
|
12. November 2005 @ 17:10 |
Link to this message
|
|
Hello all, I was just wondering if anyone knew the best way to remove the warranty sticker and it still be usable, I heard a little heat and some patience goes a long way... any help would be appreciated...
|
|
waleedwc
Senior Member
|
13. November 2005 @ 01:13 |
Link to this message
|
|
2nd2one, yes you can use a hair dryer or something, but i didnt do that, i used a pin and put it under the sticker in between the top and bottom shell and slowly slid it under the top half and removed it very slowly, the stiker wasnt damaged or anything and is still usable, dont pull the sticker of fast otherwise the words VOID will come up, if that does happen get a blank pen marker and on the sticky side of the sticker go over the words.
|
|
2nd2one
Newbie
|
13. November 2005 @ 07:12 |
Link to this message
|
|
thanks waleedwc, I got it. I used an exacto knife with a straight blade on it, and went real slow, it came off perfect...however, my sticker is on one of the screw holes on the bottom of the case. again, thanks for the help.
|
|
waleedwc
Senior Member
|
13. November 2005 @ 07:15 |
Link to this message
|
|
Your welcome 2nd2one, always here to help.
|
|
waleedwc
Senior Member
|
13. November 2005 @ 07:16 |
Link to this message
|
|
chodelord, hows your PStwo going.
|
|
2nd2one
Newbie
|
13. November 2005 @ 09:19 |
Link to this message
|
|
does anyone know where to ps2 games online???
|
|
Advertisement
|
|
|
|
poulpy
Suspended due to non-functional email address
|
29. November 2005 @ 07:26 |
Link to this message
|
|
Hi,
i've had the exact same problem as you do. I tried to put solder on the contacts but it wouldn't work. The only way i could put it on is by using a small screw on it.
Did you find any replacement part or scheme to put a switch on it ?
Thanx a lot :)
|
