|
Yamaha CRW2100e not burning
|
|
|
soccer26
Newbie
|
17. March 2003 @ 15:10 |
Link to this message
|
|
I have a Yamaha CRW2100e that won't burn. When i try nero, it sees it is there and goes through the process of burning and finishes. Nothing burnt on the cd. When i try the program the burner came with, it says it is not installed right. I have tried everything, updated Firmware 1.0n, ASPI updated, reinstalled drive, unplugged drive, searched far and wide for cure but nothing worked.
I am running Dell Dimension XPS T700r, 384 mb ram, 20GB hardrive and Windows 98SE.
~One Problem fixed, two more to be worked on~
|
|
Advertisement
|
|
|
|
|
Shoey
Suspended due to non-functional email address
|
17. March 2003 @ 22:28 |
Link to this message
|
|
What burning software are you using? In the burn process, did you untick "simulate"? Did you disable antivirus when burning?
Shoey
Asus K8N nVidia nForce3 Pro 250 GB, Athlon 64 3200+, Hitachi 80 gig SATA 150, Corsair XMS 1 gig PC4000, ATI Radeon Saphire 9600 Pro (256 DDR), Windows XP Pro (64 Bit),Lite-ON SOHD 167T,, Plextor PX-712SA,BenQ 1640.
 |
|
soccer26
Newbie
|
18. March 2003 @ 10:56 |
Link to this message
|
|
I am burning on Nero 5.5.10.7. I have unclicked "Simulate" and disabled my Norton antivirus and still nothing.
|
|
Shoey
Suspended due to non-functional email address
|
18. March 2003 @ 11:00 |
Link to this message
|
Try differnet media and a simple program called BurnAtOnce.
BurnAtOnce: http://www.burnatonce.com/index.html
Also be sure your ASPI layers are updated. Most recommended is ASPI 4.6.
Shoey ~O-O~
Asus K8N nVidia nForce3 Pro 250 GB, Athlon 64 3200+, Hitachi 80 gig SATA 150, Corsair XMS 1 gig PC4000, ATI Radeon Saphire 9600 Pro (256 DDR), Windows XP Pro (64 Bit),Lite-ON SOHD 167T,, Plextor PX-712SA,BenQ 1640.
|
|
soccer26
Newbie
|
18. March 2003 @ 13:25 |
Link to this message
|
|
I have ASPI 4.71 installed on my computer.
This was what happened when i tried Burn at Once:
Cdrdao version 1.1.7 - (C) Andreas Mueller <andreas@daneb.de>
SCSI interface library - (C) Joerg Schilling
Paranoia DAE library - (C) Monty
Using libscg version 'andreas-0.5-UNIXWARE_Patch'
0,0,0: YAMAHA CRW2100E Rev: 1.0N
Using driver: Generic SCSI-3/MMC - Version 2.0 (options 0x0010)
Starting write at speed 8...
Executing power calibration...
?: I/O error. : scsi sendcmd: retryable error
CDB: 54 01 00 00 00 00 00 00 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 04 67 67 67 3E 0A 00 00 00 00 09 00
Sense Key: 0x4 Hardware Error, Segment 0
Sense Code: 0x09 Qual 0x00 (track following error) Fru 0x0
Sense flags: Blk 1734829886 (not valid)
cmd finished after 52.329s timeout 180s
ERROR: Power calibration failed.
ERROR: Use option --force to ignore this error.
ERROR: Writing failed.
|
|
Shoey
Suspended due to non-functional email address
|
18. March 2003 @ 13:53 |
Link to this message
|
|
This message has been edited since posting. Last time this message was edited on 4. April 2003 @ 23:54
|
|
soccer26
Newbie
|
19. March 2003 @ 15:58 |
Link to this message
|
|
Well, uninstalled all burning programs and then downloaded and installed ASPI 4.6. The Burn At Once program went through the steps, acting like it was burning but nothing written on the disk. Tried it twice, one with Nero and one with Disk At Once, still nothing.
|
|
Shoey
Suspended due to non-functional email address
|
19. March 2003 @ 17:55 |
Link to this message
|
Asus K8N nVidia nForce3 Pro 250 GB, Athlon 64 3200+, Hitachi 80 gig SATA 150, Corsair XMS 1 gig PC4000, ATI Radeon Saphire 9600 Pro (256 DDR), Windows XP Pro (64 Bit),Lite-ON SOHD 167T,, Plextor PX-712SA,BenQ 1640.
|
|
soccer26
Newbie
|
20. March 2003 @ 11:34 |
Link to this message
|
|
Firmware M8? Where is that on that webpage?
|
|
Shoey
Suspended due to non-functional email address
|
20. March 2003 @ 11:39 |
Link to this message
|
Asus K8N nVidia nForce3 Pro 250 GB, Athlon 64 3200+, Hitachi 80 gig SATA 150, Corsair XMS 1 gig PC4000, ATI Radeon Saphire 9600 Pro (256 DDR), Windows XP Pro (64 Bit),Lite-ON SOHD 167T,, Plextor PX-712SA,BenQ 1640.
This message has been edited since posting. Last time this message was edited on 20. March 2003 @ 11:43
|
|
soccer26
Newbie
|
20. March 2003 @ 16:26 |
Link to this message
|
|
Where in my computer can I find out what my burner is for 100% sure? I know it is the slave under my existing CD-Rom drive. I already have the firmware 1.0n.
|
|
Shoey
Suspended due to non-functional email address
|
20. March 2003 @ 23:05 |
Link to this message
|
|
According to the information you provided, your Yamaha CRW2100 should be on port 3. Your hd is on port 1 (master or cable select)=primary ide channel, your cd-rom on port 2 (master)=secondary ide channel, and your Yamaha CRW2100 on port 3 (slave)=secondary ide channel. Open MTKFlashWINMode and click ATAPI mode,then click launch ATIPI version. The software will querry your settings and after this you can locate your Yamaha and firmware and flash your drive. BE SURE nothing is in the drive! REBOOT after flashing your Yamy and I hope this solves your problem.
Shoey
Asus K8N nVidia nForce3 Pro 250 GB, Athlon 64 3200+, Hitachi 80 gig SATA 150, Corsair XMS 1 gig PC4000, ATI Radeon Saphire 9600 Pro (256 DDR), Windows XP Pro (64 Bit),Lite-ON SOHD 167T,, Plextor PX-712SA,BenQ 1640.
This message has been edited since posting. Last time this message was edited on 20. March 2003 @ 23:11
|
|
soccer26
Newbie
|
21. March 2003 @ 10:53 |
Link to this message
|
|
Where should the Source file be?
|
|
Shoey
Suspended due to non-functional email address
|
21. March 2003 @ 11:51 |
Link to this message
|
|
Source file is the firmware you should have downloaded from the link I provided.
Shoey
|
|
soccer26
Newbie
|
24. March 2003 @ 05:27 |
Link to this message
|
|
It is burning, but with some problems but I think they will pass with time.
Thanks
|
|
Shoey
Suspended due to non-functional email address
|
24. March 2003 @ 13:49 |
Link to this message
|
|
What kind of problems?
Shoey
Asus K8N nVidia nForce3 Pro 250 GB, Athlon 64 3200+, Hitachi 80 gig SATA 150, Corsair XMS 1 gig PC4000, ATI Radeon Saphire 9600 Pro (256 DDR), Windows XP Pro (64 Bit),Lite-ON SOHD 167T,, Plextor PX-712SA,BenQ 1640.
|
|
soccer26
Newbie
|
25. March 2003 @ 05:53 |
Link to this message
|
|
Well, the first cd i burnt with it was an audio cd. It took a long time for my cd players to read each track, burnt at 8X. Then i burnt one at 4X and working fine.
|
|
soccer26
Newbie
|
1. April 2003 @ 11:31 |
Link to this message
|
|
My burner burnt 2 cds and hasnt been able to burn any more cds. I did get an error in the winflash program that said...
ERR: Could not find flash type
|
|
Shoey
Suspended due to non-functional email address
|
2. April 2003 @ 19:06 |
Link to this message
|
|
soccer26,
I provided a direct link to download 3 different firmware(s) for your Yamaha CRW2100e
and your still having problems? Download all three of them to your desktop and try each one and burn a couple of cd's and see how it goes.
The MTKFLASHWin (ide mode) program is very simple to use and you can flash the drive right from your desktop. Try using the latest firmware 1.0n.
Shoey
Asus K8N nVidia nForce3 Pro 250 GB, Athlon 64 3200+, Hitachi 80 gig SATA 150, Corsair XMS 1 gig PC4000, ATI Radeon Saphire 9600 Pro (256 DDR), Windows XP Pro (64 Bit),Lite-ON SOHD 167T,, Plextor PX-712SA,BenQ 1640.
|
|
Advertisement
|
|
|
|
soccer26
Newbie
|
4. April 2003 @ 17:42 |
Link to this message
|
|
the site that you gave me had 3 firmwares on it. The first one led me to a blank page then the last two lead me to the same website, to download firmware 1.0N. I found firmware 1.0H on the internet but still nothing. It can reconize that it is a burner and that there is or not a cd in the drive but doesnt burn when trying to burn. i have tried both IDE and ATAPI modes, nothing changed.
|
