|
xeno gc modchip problem you have to read this!!
|
|
|
johnodd4
Suspended permanently
|
31. December 2005 @ 22:41 |
Link to this message
|
|
ok i decided to purchase a xeno chip but before i did i ran into a problem a major problem
yes the chip works and also it doesn't
newer version's of the gamecube here in the u.s.a don't look like the picture for the installation image on the web page so i cannot use it on my model of gamecube
pretty dumb to design a cube chip that is only compatible with one series of cube
|
|
Advertisement
|
|
|
|
|
Venom5880
Suspended due to non-functional email address
|
31. December 2005 @ 22:44 |
Link to this message
|
|
Seriously? I thought all the laser modules were pretty much the same.
|
|
johnodd4
Suspended permanently
|
31. December 2005 @ 22:49 |
Link to this message
|
|
i thought so too
untill i purchased my new gamecube with my mobile monitor and looked at them both i found that in order to install the chip you have to apply more soilder
then the instructions apply so i fixed it just remeber that if you purchase this chip use lots of solder
|
|
boki2002
Suspended permanently
|
1. January 2006 @ 03:20 |
Link to this message
|
|
but thats not realy a hude problem, attach some wires to the correct places on the chip and link them to the correct places on the board,(if u know where they are!)
|
|
tempest9
Junior Member
|
1. January 2006 @ 04:54 |
Link to this message
|
|
Can you give more info on your GC - model, rev A, B, C, etc...
Gamecube: NTSC DOL-001 REV A - BIOS Rev 1.1 - Drive Model 04 2002/02 (61) - LaserPot = 183 ohms now tweaked to ~150
Mod Chip: XENOGC
Soft Mods(replaced by xenoGC, but still useful!): BBA, AR 1.07, SD Adapter, Samson's Loader Mem Card - GcoM2.3 for ripping
Burner/Media: NEC2100 (flashed to 2510) / Office Depot mini, Teon full size
|
|
binlookin
Newbie
|
1. January 2006 @ 13:36 |
Link to this message
|
|
hi!
i have a platinum gamecube will the instructions be good to follow in installing this chip? also, is it hard to solder i am a complete noob at soldering and modding, have very very little experience in soldering. also do i need to adjust the pot to have the backup of my originals play properly or will a good media like ritek g04 do just fine?
tia.
"I won't back out on my promise. That is my way of the ninja"
- Naruto Uzumaki
|
|
johnodd4
Suspended permanently
|
1. January 2006 @ 16:28 |
Link to this message
|
|
i have two gamecubes
1.is rev a
2.is rev c
and the differrence is really minor
|
|
nsx88
Junior Member
|
17. January 2006 @ 20:35 |
Link to this message
|
|
can anyone clarify for usa models that only more solder is required. the chip still sits in the right spot and works in a perfect manner, right?
planning to get this xenogc chip from eurasia and shipped via airmail to brampton, ontario.
anyone delt with eurasia before, mind sharing their experiences, shipping times for airmail, etc?
thanks
|
Member
|
18. January 2006 @ 02:55 |
Link to this message
|
nsx88, I bought my chip from http://www.divineo.cn. It arrived from China in around 5 days and I had to sign for it (I'm in the UK).
They also email you a tracking number you can use on Hong Kong Post's website.
|
|
nsx88
Junior Member
|
20. January 2006 @ 07:59 |
Link to this message
|
|
order mine from eurasia, hope to see it arrive within a week.
|
|
Advertisement
|
|
|
|
Spilo
Suspended due to non-functional email address
|
20. January 2006 @ 08:04 |
Link to this message
|
|
Will this chip play multi-disc games ok?
|
