|
pstwo won't spin cd's anymore
|
|
|
KainX
Suspended permanently
|
11. April 2006 @ 15:27 |
Link to this message
|
|
I was using cdloader to play a backup and left my pstwo on for a second and when i came back it was spinning the cd and froze
after restarting it i noticed it wouldn't spin cd's
then i opened it and there was this little chip under cd drives motor that smelled burnt
it turns on fine and goes to the memory card and everything but it won't spin cd's
i have playedbackups like this hundreds of times but now it won't work
can someone tell me what i can do
PS I DON'T USE A MODCHIP
currently have these consoles
Gamecube
Xbox
Ps2
Dreamcast
Phantom
Gba
psp
|
|
Advertisement
|
 |
|
|
|
waleedwc
Senior Member
|
11. April 2006 @ 16:03 |
Link to this message
|
|
Post a pic of the part that you think is burnt, its probably a blown fuse, and if you were using cd loader, did u have anything on the switched that make the ps2 think the lid is closed, if u did it could be the switch was damaged, give me more information and i will tell you how to sought the problem out.
|
|
KainX
Suspended permanently
|
11. April 2006 @ 18:33 |
Link to this message
|
here are some pics
i circled the part i think is burnt on both of them red
so what do you think i should do
currently have these consoles
Gamecube
Xbox
Ps2
Dreamcast
Phantom
Gba
psp
This message has been edited since posting. Last time this message was edited on 12. April 2006 @ 03:25
|
|
KainX
Suspended permanently
|
12. April 2006 @ 03:11 |
Link to this message
|
|
can that chip be found anywhere
currently have these consoles
Gamecube
Xbox
Ps2
Dreamcast
Phantom
Gba
psp
|
|
waleedwc
Senior Member
|
12. April 2006 @ 03:50 |
Link to this message
|
I dont have my ps2 open right now, so i cant check that pcb out, as far as i can remember, there was no chip on that board, it just connects the wires upto the motor, but i will have to check, when you rotate the motor does it rotate smoothly or is it there like crackling noises when your rotating it, and secondly have to checked all the fuses on the motherboard, if not i think you should get a multi meter and check all the fuses. The diagram link it below, once you have checked the fuses let me know, and are they and chips on that PCB where the motor is?
http://www.picsystems.net/imagenes_fuses/v12.jpg
|
|
waleedwc
Senior Member
|
12. April 2006 @ 03:53 |
Link to this message
|
|
I took a more closer look at your picture, and the switch at the back of the motherboard looks like its broken or something, take a close pic of it and post it, your problem probably lies there, that switch needs to work, when you close the lid that switch tells the ps2 the lids closed it it powers up the motor circuit, without it you cant do anything.
|
|
Xmodds
Member
|
12. April 2006 @ 04:51 |
Link to this message
|
|
yes, you need to get that switch soldered back on
|
|
KainX
Suspended permanently
|
12. April 2006 @ 05:18 |
Link to this message
|
|
it can't be the switch because its not broken because i can feel it and when the lid goes down the laser moves into position but the cd still dosen't rotate
is it possible for the motor to burn out because the motor and that little board smeel burnt
currently have these consoles
Gamecube
Xbox
Ps2
Dreamcast
Phantom
Gba
psp
This message has been edited since posting. Last time this message was edited on 12. April 2006 @ 05:19
|
|
Xmodds
Member
|
12. April 2006 @ 05:27 |
Link to this message
|
|
guess its not a good picture but it sure does look like it, but looking again you laser looks burnt, look closely at the eye and see if its melted a little
|
|
KainX
Suspended permanently
|
12. April 2006 @ 05:49 |
Link to this message
|
|
its not it looks normal
currently have these consoles
Gamecube
Xbox
Ps2
Dreamcast
Phantom
Gba
psp
|
|
KainX
Suspended permanently
|
12. April 2006 @ 05:49 |
Link to this message
|
|
do you think replacing both the motor and laser would fix the problem
the switch looks broken because i had black electrical tape on it but it still works
currently have these consoles
Gamecube
Xbox
Ps2
Dreamcast
Phantom
Gba
psp
This message has been edited since posting. Last time this message was edited on 12. April 2006 @ 05:51
|
|
Xmodds
Member
|
12. April 2006 @ 05:54 |
Link to this message
|
|
try replacing laser first
|
|
KainX
Suspended permanently
|
12. April 2006 @ 05:57 |
Link to this message
|
|
i found a complete unit of the laser and motor on ebay
think its worth it
27 bucks
currently have these consoles
Gamecube
Xbox
Ps2
Dreamcast
Phantom
Gba
psp
This message has been edited since posting. Last time this message was edited on 12. April 2006 @ 05:57
|
|
Advertisement
|
|
|
|
Xmodds
Member
|
12. April 2006 @ 06:12 |
Link to this message
|
|
check pm
|
