|
Hitachi 0078fk drive?
|
|
|
xxsaijin
Member
|
7. December 2006 @ 19:10 |
Link to this message
|
|
I can't remember where I read it, not sure if I remember any of it even right but could someone clarify this:
Does flashing this drive require a different method? I read some where you need a chip or something? ( sorry still a newb )
I saw a post that a FW was released for this, now I'm not asking where it can be found, but if it can be found by that I mean has anyone else found it on there own. I myself looked for i'd say an hour couldn't find it....
PS just taking the xbox 360 apart was deadly LOL, I watched 3 different videos and from what I saw in the videos and did myself MS has slightly added a few precautions to stop from opening the case.
1. from the HDD side to remove that grey peice one of the pegs are so far back that the pocking through the wholes didn't work for me, I had to work around them by removing 5/6 tabs then opening the case and the grey peice just slid out.
2. theres a metal foil tape attaching the drive to the case, its underneith so it took me a few minutes to figure out why I couldnt lift up my drive.
Has anyone else faced these problems? I'd like to think I'm the first to discover this hehe.
xxSaijin |
|
Advertisement
|
 |
|
|
AfterDawn Addict
1 product review
|
7. December 2006 @ 19:53 |
Link to this message
|
|
There is no "normal" firmware released for this drive. Anything you see will probably just brick your 360. The only way right now to flash it unless there's been a very recent change is to remove a chip which is encased in hard black resin and you'll need a workstation for flashing it. Then you'll have to get the chip back on there which is pretty hard.
here's the basic steps:
1) You cannot read FW or Key while the chip containing it is on the drive (ATM). It must be removed.
2) You must remove the chip WITHOUT damaging it. You'll have to heat the epoxy both around and under the chip and de-solder it with suitable tools.
3) Use a programmer that can handle the 39VF020. Get the FW Dump. Patch the 1.6 FW / Encrypt and Re-program a new chip.
4) Re-solder the chip to the board 100% (this is where most go wrong). You'll need a good quality iron and rework station and board cleaner.
This isn't the for faint of heart or inexperienced. If you don't have a great deal of experience in these type things it's best to find a professional who can do it for you or sell your 360 and look for one with a different drive.
This message has been edited since posting. Last time this message was edited on 7. December 2006 @ 20:00
|
|
xxsaijin
Member
|
7. December 2006 @ 20:15 |
Link to this message
|
|
WoW.... really that just crushed my spirit.... I spent soo much time reading up and everything.... Im just crushed. Is there anyway to tell outside the box before even buying it wat type of drive its gonna have, Kind of like the psp there were certain letters that told you what FW was on board?
xxSaijin
|
AfterDawn Addict
1 product review
|
7. December 2006 @ 20:22 |
Link to this message
|
Yes there is. Although, this isn't 100% since it's just what people report, but it still seems to be pretty spot on. Look at the lot number on the outside of the box in the store. Check it against this database. http://www.360drives.com/list?sort=lotno Out of curiosity I found one MS25 a Target last week, while the rest were 0078FKs. I think there was a MS28 too. If you just bought your 360 I'd take it back and look for a more suitable one.
This message has been edited since posting. Last time this message was edited on 7. December 2006 @ 20:25
|
|
xxsaijin
Member
|
7. December 2006 @ 21:03 |
Link to this message
|
|
what would be my excuse.... See heres the deal, I've already exchnged one bundle for another for more features. What can I really say...? That I want one with a different lot number...
xxSaijin
|
|
Azrea1
Member
|
8. December 2006 @ 03:36 |
Link to this message
|
|
lol i just tell them it shut off after an hour or so, they really dont care its not there 360 and it doesnt effect them if they sell it or not (atleast not bestbuy, walmart, gamestop, ect)
|
AfterDawn Addict
1 product review
|
8. December 2006 @ 06:47 |
Link to this message
|
|
Since it's a bundle I don't know if they'd give you crap if it came with games you and opened then. I'd just say I changed my mind and would like a refund. I'm getting a PS3 instead.
|
AfterDawn Addict
|
8. December 2006 @ 06:56 |
Link to this message
|
|
pl so is the 59DJ, MS25, 0047DJ, MS28 FW's all good and flashable?
|
AfterDawn Addict
1 product review
|
8. December 2006 @ 07:01 |
Link to this message
|
|
Yes, MS28 requires a trickier method than MS25, but it's still doable.
|
AfterDawn Addict
|
8. December 2006 @ 08:08 |
Link to this message
|
|
is it by the way of the resistor? and mode b? and also 78FK cant be flashed right...
|
|
xxsaijin
Member
|
9. December 2006 @ 15:09 |
Link to this message
|
|
YES I went to Futureshop, and exchanged my 360 for a MS28 one the manager was soo chill when I told him I need it to play burned games HAHA!
xxSaijin
|
|
6Ripper9
Junior Member
|
9. December 2006 @ 17:18 |
Link to this message
|
Originally posted by xxsaijin:
YES I went to Futureshop, and exchanged my 360 for a MS28 one the manager was soo chill when I told him I need it to play burned games HAHA!
LOL!! That's funny that you actually told him that, lol. I have to buy a new one, and return the dead one. I really hope I get another Samsung drive. I'm taking a list I printed off the 360 Drives site.
|
Senior Member
1 product review
|
9. December 2006 @ 20:15 |
Link to this message
|
|
lol nice.
now flash the m28 with the 10 sec methid.
btw: wait is actaully like 15 sec.
|
|
xxsaijin
Member
|
10. December 2006 @ 03:50 |
Link to this message
|
|
Can anyone recommend the best FW to use for flashing the MS28 Drive and a good tutorial/video? Thanks to anyone that can!
xxSaijin
|
|
Saber9
Suspended due to non-functional email address
|
10. December 2006 @ 04:25 |
Link to this message
|
|
|
|
6Ripper9
Junior Member
|
10. December 2006 @ 07:46 |
Link to this message
|
Originally posted by Saber9:
Use Xtreme 4.2A
Is there a big difference between 4.2A and 4.2B?
|
|
backup
Suspended due to non-functional email address
|
10. December 2006 @ 09:05 |
Link to this message
|
|
i know i have got a 360 for xmas with the dreaded hitachi drive but i dont think it will be much of a problem within the new year ;)
|
|
6Ripper9
Junior Member
|
10. December 2006 @ 09:23 |
Link to this message
|
|
|
|
backup
Suspended due to non-functional email address
|
10. December 2006 @ 09:25 |
Link to this message
|
|
bingo !!!! there is currently 50 beta testers on this product team xecuter rocks
as long as you have a sammy 162 things should be fine ... yipee :)
This message has been edited since posting. Last time this message was edited on 10. December 2006 @ 09:28
|
|
Saber9
Suspended due to non-functional email address
|
11. December 2006 @ 13:29 |
Link to this message
|
Quote:
Originally posted by Saber9:
Use Xtreme 4.2A
Is there a big difference between 4.2A and 4.2B?
4.2A is supposed to read the game at 12X the same speed as originals.
4.2B is supposed to read slower but be less noisy.
Been using 4.2A so far and it works great. Reads backups smoother than originals.
|
|
xxsaijin
Member
|
11. December 2006 @ 14:04 |
Link to this message
|
|
Wow ok 4.2a it is. Ok here are a few more questions for you.
1. Do I need a Xecuter connector for this task/would it actually make it easier? If so how would it work? Don't you need to do that 10 second trick?
2. Once flash can I use Xbox Live?
3. Will the update from Xbox live mess my flash up?
4. Before I can even begin I need a SATA connector, I checked inside my PC to see if my motherboard had one but sadly no. Also my Pc is about 6 years old, rite around when the first XP was released. I know my motherbaord doesnt support PCI so is there any one way for me to get this connected? Maybe an AGP SATA connector?
5. Anyone got a much more updated video/tutorial on the flashing of the MS28, that video didnt explain a few things....
SUPER thanks to anyone that can answeer a few questions. Really I'd GREATLY appreciate it.
xxSaijin
|
|
xxsaijin
Member
|
12. December 2006 @ 10:17 |
Link to this message
|
|
Anyone?
xxSaijin
|
|
backup
Suspended due to non-functional email address
|
12. December 2006 @ 10:21 |
Link to this message
|
|
the best tool at the moment is the x360usb but they are only available in the kit form at the moment ...where ive been looking anyway for around 30 -35 quid man the blaster 360 needs releasing along with the x78
|
|
Advertisement
|
|
|
|
xxsaijin
Member
|
12. December 2006 @ 11:00 |
Link to this message
|
|
Ok I read up on the 360 USB but under compatibility it states only with the Hitachi drives... But under the product features it states works with any SATA hd or drive? :S I'm confused on top of that do I need to buy the Xecutor connector kit or does it come with it? I also have a MS28 drive so wouldnt I need the power still coming from the 360 with the video cable plugged in? It said that if I didn't the 360 might shut off in the middle of the flashing process and fcuk everything up.
xxSaijin
|
