|
|
|
Just Updated to XP Pro - Burner will not work... Help.
|
|
|
bartidge
Newbie
|
30. September 2003 @ 21:48 |
Link to this message
|
|
Hi-
I just updated to XP Pro from Windows '98... and have had no luck getting my burner to work in XP...
Specs.
System: P3, 500 MhZ, 128 MB Ram, Seagate 120 GB master drive.
Burner Info.:
Yamaha CRW6416SZ, SCSI Interface
16X Read
6X Write
Firmware Version: 1.0d
SCSI Specs.
Adaptec AHA-2930CU PCI SCSI Controller
Drivers:
1. aic78xx Adaptec Ultra SCSI miniport version 3.60a (Lab01_N.010510-0033)
2. Cdrom SCSI CD-Rom Driver version 5.1.2600.1106 (xpsp1.020828-1920)
-I've done all critical windows updates and most all XP updates (except for a couple advanced networking updates for business/LAN)
-I've updated my yamaha CD-R drive firmware and disabled 'autorun' and DMA settings before flashing the firmware.
-I've tried 3 different software programs (Roxio Easy CD 5.5, Nero 6.0 and Hotburn)- none will work.
-Roxio and Hotburn try to burn - Roxio creates an unreadable disc. Hotburn hits 99% complete and locks up. Nero locks up immediately and gives 'Unknown BurnPhase' error.
Can anyone offer some advice?
Thx.
|
|
Advertisement
|
 |
|
|
AfterDawn Addict
|
30. September 2003 @ 22:03 |
Link to this message
|
|
hi
did you install your burning apps "after installing XP" ???? if not uninstall and install again !!!!!! you may be on win98 drivers!
also install adaptec.com ASPI layer! just go to there site and download and install and reboot!
then let us know if it works ok!
after those 2 things i would put "DMA" back on!!!!!
Thx...
Nothing here to see, move along folks.
 |
|
bartidge
Newbie
|
1. October 2003 @ 14:52 |
Link to this message
|
hi-
I un-installed Nero, disabled DMA on primary and secondary IDE's and dowloaded the Adaptec ASPI layer 4.71 for XP and installed. I then re-enabled DMA and rebooted - then re-installed Nero and proceeded to try and burn an audio cd... same 'Nero BurnPhase Error' when burning tried to begin...
Should Autorun be back on in the registry maybe???
Any other ideas?
|
|
Shoey
Suspended due to non-functional email address
|
1. October 2003 @ 17:53 |
Link to this message
|
DMA should be enabled m8. In Device Manager>IDE DVD\CD-Rom, does it say where your Yamy is that "this device is working properly"? Any "yellow" markers? Yamaha is out of the cd burner business and it appears much burning software doesn't support Yamaha cd burners. Try The Firmware Page to be absolutly sure your using the latest firmware and if you are, well then... Autorun should be enabled if you play backups of Safedisc 2.8-2.9 Try burnatonce (freebie) and burn a data disc and see what happens. I would uninstall any packet write software (if applicable) for now.
The Firmware Page: http://forum.rpc1.org/portal.php
burnatonce 0.99a
http://www.burnatonce.com/downloads/
Shoey :)_
Asus K8N nVidia nForce3 Pro 250 GB, Athlon 64 3200+, Hitachi 80 gig SATA 150, Corsair XMS 1 gig PC4000, ATI Radeon Saphire 9600 Pro (256 DDR), Windows XP Pro (64 Bit),Lite-ON SOHD 167T,, Plextor PX-712SA,BenQ 1640.
 This message has been edited since posting. Last time this message was edited on 1. October 2003 @ 17:57
|
|
bartidge
Newbie
|
5. October 2003 @ 06:11 |
Link to this message
|
Hi-
Thanks for the info. Couple things...
1. I've read thru a number of pages on the forum that seem to indicate that the most current yahmaha firmware version for my drive (1.0d) is problematic... other member posts have said that I should revert back to firmware vers. 1.0c. (didn't see that recommendation related to my specific yammy model, but other models in the yammy family...)Think that would be worth a try?
2. ASPI: seems that my ASPI layer has conflicts and is corrupted... I updated the ASPI to the most current Adaptec version then installed Nero 6(which appears to have tried to overwrite with it's own ASPI layer)In any event, Nero InfoTool says the ASPI layer is corrupted... below is a complete InfoTool profile on my Yammy CD-R/RW drive, drivers, ASPI etc... can you take quick look and see if you see any other problems.
Also, what's the best way to clear up my ASPI problem with Nero?
---
Drive Information
-----------------
Drive : YAMAHA CRW6416S
Type : CD-RW Recorder
Firmware Version : 1.0d
Buffer Size : 2 MB
Date : 30-05-00
Serial : ?
Drive : H:\
Location : 2:3
Mechanism : Tray
Read Speed : 16, 10, 6, 4, 2, 1 X
Write Speed : 6, 4, 1 X
Read CD Text : No
Return C2 Pointers : No
Read CD-R : Yes
Read CD-RW : Yes
Read DVD-ROM : No
Read DVD-RAM : No
Read DVD-R : No
Read DVD-RW : No
Read DVD+R : No
Read DVD+RW : No
Read Digital Audio : Yes
Read CD+G : Yes
Read VideoCD : Yes
Write CD-R : Yes
Write CD-RW : Yes
Write DVD-R : No
Write DVD-RW : No
Write DVD+R : No
Write DVD+RW : No
Write DVD-RAM : No
Buffer Underrun Protection : No
Mount Rainier : No
Modes : Packet, TAO, DAO, SAO, RAW SAO, RAW SAO 16, RAW SAO 96, RAW DAO 96
Disc Information (H:\)
-------------------
Type : - no disc inserted -
Interface Information
---------------------
Adapter 1
---------
Description : Primary IDE Channel
Driver
Description : System32DRIVERS\atapi.sys
Company : Microsoft Corporation
Version : 5.1.2600.1106 (xpsp1.020828-1920)
Description : IDE/ATAPI Port Driver
Attached Devices
Description
Master : ST3120024A
Type : Disk Drive
DMA : On
Description
Slave : Maxtor 91741U4
Type : Disk Drive
DMA : On
Adapter 2
---------
Description
Secondary IDE Channel
Driver
Description : System32\DRIVERS\atapi.sys
Company : Microsoft Corporation
Version : 5.1.2600.1106 (xpsp1.020828-1920)
Description : IDE/ATAPI Port Driver
Attached Devices
Description : Master: TOSHIBA DVD-ROM SD-M1202
Type : CD-Rom Drive
DMA : On
Autorun : Off
Description : Slave: IOMEGA ZIP 100
Type : Disk Drive
DMA : Off
Adapter 3
---------
Description : Adaptec AHA-2930CU PCI SCSI Controller
Driver
Description : System32\DRIVERS\aic78xx.sys
Company : Microsoft Corporation
Version : v3.60a (Lab01_N.010510-0033)
Description : Adaptec Ultra SCSI miniport
Attached Devices
Description : ID 3 (0): YAMAHA CRW6416S 1.0d
Type : CD-Rom Drive
Autorun : Off
Software Information
--------------------
Operating System : Windows XP Professional (5.01.2600 Service Pack 1)
ASPI : Nero Aspi Library 2.0.1.56 Ahead Software AG
Description : Nero Burning ROM
Version : 6, 0, 0, 0
Company : Ahead Software AG
Version Check : Ok
Hardware Information
--------------------
CPU : Pentium III 500 MHz
Bus Speed : 100 MHz
Motherboard : BIOSTAR M6TWG
System :
BIOS : Award 6.00 PG
Memory : 128 MB (6ns)
Sound : Intel(r) Integrated Audio
Video : Intel(r) 82810 Graphics Controller
Driver Information
------------------
Driver : ac97intc
Description : Intel(r) Integrated Controller Hub Audio Driver
Version : 5.10.3523 built by: WinDDK
Company : Intel Corporation
Driver : aic78xx
Description : Adaptec Ultra SCSI miniport
Version : v3.60a (Lab01_N.010510-0033)
Company : Microsoft Corporation
Driver : Aspi32
Description : ASPI for WIN32 Kernel
Driver Version : 4.71 (0002) built by: WinDDK
Company : Adaptec
Driver : atapi
Description : IDE/ATAPI Port Driver
Version : 5.1.2600.1106 (xpsp1.020828-1920)
Company : Microsoft Corporation
Driver : audstub
Description : AudStub Driver
Version : 5.1.2600.0 (XPClient.010817-1148)
Company : Microsoft Corporation
Driver : Cdfs
Description : CD-ROM File System Driver
Version : 5.1.2600.1106 (xpsp1.020828-1920)
Company : Microsoft Corporation
Driver : Cdrom
Description : SCSI CD-ROM Driver
Version : 5.1.2600.1106 (xpsp1.020828-1920)
Company : Microsoft Corporation
Driver : Disk
Description : PnP Disk Driver
Version : 5.1.2600.1106 (xpsp1.020828-1920)
Company : Microsoft Corporation
Driver : dmio
Description : NT Disk Manager I/O Driver Version : 2600.0.503.0
Company : Microsoft Corp., Veritas Software
Driver : dmload
Description : NT Disk Manager Startup Driver
Version : 2600.0.503.0
Company : Microsoft Corp., Veritas Software.
Driver : Fastfat
Description : Fast FAT File System Driver
Version : 5.1.2600.1106 (xpsp1.020828-1920)
Company : Microsoft Corporation
Driver : Fdc
Description : Floppy Disk Controller Driver
Version : 5.1.2600.0 (XPClient.010817-1148)
Company : Microsoft Corporation
Driver : Flpydisk
Description : Floppy Driver
Version : 5.1.2600.1106 (xpsp1.020828-1920)
Company : Microsoft Corporation
Driver : Ftdisk
Description : FT Disk Driver
Version : 5.1.2600.0 (XPClient.010817-1148)
Company : Microsoft Corporation
Driver : gameenum
Description : Game Port Enumerator
Version : 5.1.2600.1106 (xpsp1.020828-1920)
Company : Microsoft Corporation
Driver : i8042prt
Description : i8042 Port Driver
Version : 5.1.2600.1106 (xpsp1.020828-1920)
Company : Microsoft Corporation
Driver : Imapi
Description : IMAPI Kernel Driver
Version : 5.1.2600.1106 (xpsp1.020828-1920)
Company : Microsoft Corporation
Driver : IntelIde
Description : Intel PCI IDE Driver
Version : 5.1.2600.1106 (xpsp1.020828-1920)
Company : Microsoft Corporation
Driver : IPSec
Description : IPSec Driver
Version : 5.1.2600.1106 (xpsp1.020828-1920)
Company : Microsoft Corporation
Driver : isapnp
Description : PNP ISA Bus Driver
Version : 5.1.2600.0 (xpclient.010817-1148)
Company : Microsoft Corporation
Driver : kmixer
Description : Kernel Mode Audio Mixer
Version : 5.1.2600.1106 (xpsp1.020828-1920)
Company : Microsoft Corporation
Driver : Modem
Description : Modem Device Driver
Version : 5.1.2600.0 (xpclient.010817-1148)
Company : Microsoft Corporation
Driver : MODEMCSA
Description : Unimodem CSA Filter
Version : 5.1.2600.0 (xpclient.010817-1148)
Company : Microsoft Corporation
Driver : MRxDAV
Description : Windows NT WebDav Minirdr
Version : 5.1.2600.0 (xpclient.010817-1148)
Company : Microsoft Corporation
Driver : NaiFiltr
Description : N/A
Version : N/A
Company : N/A
Driver : NdisTapi
Description : NDIS 3.0 connection wrapper driver
Version : 5.1.2600.0 (xpclient.010817-1148)
Company : Microsoft Corporation
Driver : Ndisuio
Description : NDIS User mode I/O Driver
Version : 5.1.2600.1106 (xpsp1.020828-1920)
Company : Microsoft Corporation
Driver : NdisWan
Description : MS PPP Framing Driver (Strong Encryption)
Version : 5.1.2600.1106 (xpsp1.020828-1920)
Company : Microsoft Corporation
Driver : Npfs
Description : NPFS Driver
Version : 5.1.2600.0 (xpclient.010817-1148)
Company : Microsoft Corporation
Driver : Ntfs
Description : NT File System Driver
Version : 5.1.2600.1106 (xpsp1.020828-1920)
Company : Microsoft Corporation
Driver : Parport
Description : Parallel Port Driver
Version : 5.1.2600.1106 (xpsp1.020828-1920)
Company : Microsoft Corporation
Driver : PartMgr
Description : Partition Manager
Version : 5.1.2600.0 (XPClient.010817-1148)
Company : Microsoft Corporation
Driver : ParVdm
Description : VDM Parallel Driver
Version : 5.1.2600.0 (XPClient.010817-1148)
Company : Microsoft Corporation
Driver : PCI
Description : NT Plug and Play PCI Enumerator
Version : 5.1.2600.1106 (xpsp1.020828-1920)
Company : Microsoft Corporation
Driver : PSched
Description : MS QoS Packet Scheduler
Version : 5.1.2600.1106 (xpsp1.020828-1920)
Company : Microsoft Corporation
Driver : Ptilink
Description : Parallel Technologies DirectParallel IO Library
Version : 1.10 (XPClient.010817-1148)
Company : Parallel Technologies, Inc.
Driver : Rasl2tp
Description : RAS L2TP mini-port/call-manager driver
Version : 5.1.2600.1106 (xpsp1.020828-1920)
Company : Microsoft Corporation
Driver : RasPppoe
Description : RAS PPPoE mini-port/call-manager driver
Version : 5.1.2600.0 (xpclient.010817-1148)
Company : Microsoft Corporation
Driver : Raspti
Description : PTI DirectParallel(R) mini-port/call-manager driver
Version : 5.1.2600.0 (xpclient.010817-1148)
Company : Microsoft Corporation
Driver : Rdbss
Description : Redirected Drive Buffering SubSystem Driver
Version : 5.1.2600.1106 (xpsp1.020828-1920)
Company : Microsoft Corporation
Driver : RDPCDD
Description : RDP Miniport
Version : 5.1.2600.0 (xpclient.010817-1148)
Company : Microsoft Corporation
Driver : rdpdr
Description : Microsoft RDP Device redirector
Version : 5.1.2600.1106 (xpsp1.020828-1920)
Company : Microsoft Corporation
Driver : redbook
Description : Redbook Audio Filter Driver
Version : 5.1.2600.1106 (xpsp1.020828-1920)
Company : Microsoft Corporation
Driver : rtl8139
Description : NDIS 5.0 driver
Version : 5.396.0530.2001
Company : Realtek Semiconductor Corporation
Driver : serenum
Description : Serial Port Enumerator
Version : 5.1.2600.0 (XPClient.010817-1148)
Company : Microsoft Corporation
Driver : Serial
Description : Serial Device Driver
Version : 5.1.2600.1106 (xpsp1.020828-1920)
Company : Microsoft Corporation
Driver : sr
Description : System Restore Filesystem Filter Driver
Version : 5.1.2600.1106 (xpsp1.020828-1920)
Company : Microsoft Corporation
Driver : Srv
Description : Server driver
Version : 5.1.2600.1193 (xpsp2.030327-2018)
Company : Microsoft Corporation
Driver : swenum
Description : Plug and Play Software Device Enumerator
Version : 5.3.0000000.900 built by: DIRECTX
Company : Microsoft Corporation
Driver : sysaudio
Description : System Audio WDM Filter
Version : 5.1.2600.1106 (xpsp1.020828-1920)
Company : Microsoft Corporation
Driver : Tcpip
Description : TCP/IP Protocol Driver
Version : 5.1.2600.1106 (xpsp1.020828-1920)
Company : Microsoft Corporation
Driver : TermDD
Description : Terminal Server Driver
Version : 5.1.2600.1106 (xpsp1.020828-1920)
Company : Microsoft Corporation
Driver : Update
Description : Update Driver
Version : 5.1.2600.0 (XPClient.010817-1148)
Company : Microsoft Corporation
Driver : usbhub
Description : Default Hub Driver for USB
Version : 5.1.2600.1243 (xpsp2.030702-2125)
Company : Microsoft Corporation
Driver : usbuhci
Description : UHCI USB Miniport Driver
Version : 5.1.2600.1243 (xpsp2.030702-2125)
Company : Microsoft Corporation
Driver : VolSnap
Description : Volume Shadow Copy Driver
Version : 5.1.2600.0 (XPClient.010817-1148)
Company : Microsoft Corporation
Driver : Wanarp
Description : MS Remote Access and Routing ARP Driver
Version : 5.1.2600.0 (xpclient.010817-1148)
Company : Microsoft Corporation
Driver : wdmaud
Description : MMSYSTEM Wave/Midi API mapper
Version : 5.1.2600.1106 (xpsp1.020828-1920)
Company : Microsoft Corporation
Driver : msvcrt.dll
Version : 7.0.2600.1106 (xpsp1.020828-1920)
Driver : msvcirt.dll
Version : 7.0.2600.0 (xpclient.010817-1148)
Driver : mfc42.dll
Version : 6.00.8665.0
Driver : msvcp60.dll
Version : 6.00.8972.0
Driver : ole32.dll
Version : 5.1.2600.1263 (xpsp2.030819-2129)
Driver : olepro32.dll
Version : 5.0.5014
Driver : oledlg.dll
Version : 1.0 (XPClient.010817-1148)
Driver : advapi32.dll
Version : 5.1.2600.1106 (xpsp1.020828-1920)
Driver : comctl32.dll
Version : 5.82 (xpsp1.020828-1920)
Driver : setupapi.dll
Version : 5.1.2600.1106 (xpsp1.020828-1920)
Lower Filters
-------------
Upper Filters
-------------
Video Codecs
------------
Cinepak codec by Radius : 1.10.0.6
Intel 4|2|0 Video V2.50 : 4.4.3400
Intel Indeo(R) Video R3.2 : Intel Indeo(R) Video R3.2
Intel Indeo® Video 4.5 : 4.51.16.03
Intel IYUV codec : 5.1.2600.0 (XPClient.010817-1148)
Microsoft RLE : 5.1.2600.1106 (xpsp1.020828-1920)
Microsoft Video 1 : 5.1.2600.0 (xpclient.010817-1148)
Microsoft YUV : 5.3.0000000.900 built by: DIRECTX
Microsoft YUV : 5.3.0000000.900 built by: DIRECTX
Toshiba YUV codec : 5.1.2600.0 (XPClient.010817-1148)
Microsoft YUV : 5.3.0000000.900 built by: DIRECTX
Microsoft H.263 Video codec : 4.4.3400
Microsoft H.261 Video codec : 4.4.3400
Indeo® video 5.10 : R.5.10.15.2.55
Audio Codecs
------------
Microsoft IMA ADPCM codec : 4.00.0.0
Microsoft ADPCM codec : 4.00.0.0
Microsoft CCITT G.711 A-Law and u-Law codec : 4.00.0.0
Microsoft GSM 6.10 Audio codec : 4.00.0.0
DSP Group TrueSpeech(TM) Software codec : 1.00.0.0
Microsoft G.723.1 codec : 1.02.0.1
Windows Media Audio : 4.02.0.0
Sipro Lab Telecom ACELP.net audio codec : 3.02.0.0
Indeo® audio software : 2.05.0.53
Fraunhofer IIS MPEG Layer-3 codec (advanced): 1.09.1.49
Microsoft PCM Converter : 5.00.0.0
ASPI Information
----------------
System ASPI : ASPI installation is corrupted
WNASPI32.DLL : 4.71 (0002) 45056 bytes July 17, 2002
ASPI32.SYS : 4.71 (0002) built by: WinDDK 16512 bytes July 17, 2002
Nero ASPI : ASPI is installed and working properly
WNASPI32.DLL : 2.0.1.56 163910 bytes April 02, 2003
|
|
Praetor
Moderator
|
5. October 2003 @ 11:30 |
Link to this message
|
1. Nero uses its own aspi so you dont need to worry about that.
2. Just use the ASPICHK tool to see if your ASPI is installed correctly (dont trust Nero InfoTools!)
3. I reccommend ASPI 4.60 (1021) but you can also try the latest too (i think it is 4.72). Installing ASPI is a simple task requiring one reboot.
For more information regarding ASPI see http://cd-rw.org/articles/archive/aspisetup.cfm
|
|
bartidge
Newbie
|
6. October 2003 @ 15:07 |
Link to this message
|
I uninstalled Nero then I did the ASPICHCK and I have the following:
component version size
ASPI32.SYS 4.71.2 16512 bytes
WOWPOST.EXE Not Installed
WINASPI.DLL Not Installed
WNASPI32.DLL 4.71.2 45056 bytes
I then installed buratonce software and received the following errors when I tried to open the software...
---
Error 0:
Error occurred in: frmMain:scanbus
App Version: 0.99a Windows Version: 5.1.2600
---
Error 424: Object required
Error occurred in: frmMain:getDrivers
App Version: 0.99a Windows Version: 5.1.2600
---
Error 424: Object required
Error occurred in: frmMain:getDeviceIndex
App Version: 0.99a Windows Version: 5.1.2600
---
and a few more errors... when I cliked thru the errors and opened the software, burnatonce could not see my burner...
I am at my wits end... could be a new burner will be necessary... I don't think this one will work with XP...
|
|
Praetor
Moderator
|
6. October 2003 @ 20:00 |
Link to this message
|
|
Try this:
1. Uninstall EVERY SINGLE STINKIN burning app
2. Install Nero
3. Install Alcohol, CloneCD, Blindwrite, whatever
4. Install ASPI 4.60 (1021)
|
AfterDawn Addict
|
6. October 2003 @ 23:16 |
Link to this message
|
|
hi all
you may need use "Force aspi layer" and its 4.60 do a search here or ask SHOEY on the CDR thread!
Thx...
Nothing here to see, move along folks.
|
|
Praetor
Moderator
|
7. October 2003 @ 00:10 |
Link to this message
|
|
|
bartidge
Newbie
|
7. October 2003 @ 05:02 |
Link to this message
|
Yes - I did try ForceASPI at one point as well...
But I will give it another try...
I did submit a support inquiry to yahmaha to see if they could offer any suggestions...
Has anyone heard that I may need to revert back to an earlier version of Yahmaha firmware to solve the problem?
I read a couple threads that were for another yahmaha model that said that firmware version 1.0d is problematic and that earlier version 1.0c should be installed... any truth to that? I have been searching for firmware 1.0c but have yet been able to find it...
Also, the firmware indicates that 'Autorun' and DMA on all IDE's should be disabled for just about all versions of Windows before flashing (however, they make no mention of this being necessary for XP...) I've tried it both ways (disabled and not disabled)with no luck either way... should Autrun and DMA be disabled when flashing firmware to an XP op system?
Thanks.
CB
|
|
bartidge
Newbie
|
8. October 2003 @ 06:33 |
Link to this message
|
|
well - some progress I guess.
I did ASPI check and noticed that a couple of the dll files were not installed for some reason...
I unistalled all burning aps... I then re-flshed the firmware with DMA disabled on IDE's and Autorun turned off in registry.
I rebooted and turned Autorun and DMA back on and rebooted again...
Then, I Killed the exiting ASPI and dumped it and rebooted. I then installed force aspi and aspi check looked good.
I then installed burnatonce and the program installed fine and opened with no errors.
I then tried to burn an audio disc... the disc burned but the buffer only performed at 99% capacity and the disc was unreadable when I tried to open it.
I then tried to burn a data disc and that process errored out immediately...
Any next ideas?
|
|
Praetor
Moderator
|
9. October 2003 @ 09:05 |
Link to this message
|
|
A new burner. (ASUS 522452 :-) )
|
|
Shoey
Suspended due to non-functional email address
|
9. October 2003 @ 09:42 |
Link to this message
|
Quote:
A new burner.
Well I honestly believe this is a firmware issue. When you went to "The Firmware Page", did you download all firmware for your Yamy, flash, burn, errors? Try this and if you are unsuccessfull, then grab a Memorex 52MAXX cd burner (butta cutta) for backing up pc game protection (Safedisc 2.9& SecuROM 4.8.4) and cost less than the Asus 52x cd burner . Asus 52x is the better "all around burner" but the Memorex 52MAXX extracts audio fast enough, great dae accuracy, supports Mt. Rainer as well.
The Firmware Page
http://forum.rpc1.org/portal.php
Go to download firmware>Yamaha cd burner
Shoey :)
Asus K8N nVidia nForce3 Pro 250 GB, Athlon 64 3200+, Hitachi 80 gig SATA 150, Corsair XMS 1 gig PC4000, ATI Radeon Saphire 9600 Pro (256 DDR), Windows XP Pro (64 Bit),Lite-ON SOHD 167T,, Plextor PX-712SA,BenQ 1640.
|
|
Advertisement
|
|
|
|
bartidge
Newbie
|
9. October 2003 @ 10:48 |
Link to this message
|
|
yes - I've tried so many combinations with the firmware...
Reality is the last available firmware Vers. 1.0d says it's for XP (and NT, 2000, etc.) on the yahmaha download page but it was obviously developed/released w/o XP in mind, as the install dialogues make no mention of XP when you install and flash... just about every other Windows op system except xp is mentioned (including 2000 and NT) - so I think this was their last firmware release before exiting the burner business and it actually doesn't really work in XP...
But it could be a SCSI/ASPI thing too I suppose...
For the amount of time I've spent trying to figure this out, I could have bought a new burner... just want to make sure I don't chub up for a newbie and still encounter the same probs...
|
|
