|
Setting up Star View 3 in Galway
|
|
|
minstralb
Suspended due to non-functional email address
|
19. November 2008 @ 07:01 |
Link to this message
|
Hello,
Issue : Problems setting up a starview 3 super box
Location and provider : Galway cable (N**)
yesterday I tried to install the starview 3 super box. I disconnected by cable provider box and replaced it with the starview (ensuring that the Scart and Cable antenna wire were connected up properly)
After carrying out the autoscan procedure, i breifly manged to get BBC 1. However, it froze and I had to power cycle the box.
I powered up again, and repeated the autoscan. After autoscan i exited the menu to bbc 1 and i got the message " date is being updated (0%)"
After checking this forum i followed the instructions and went into the CAS 1570 menu and made sure the EMU key was on and that i set the default key. I exited out to BBC 1 again, the " date is being updated (0%)" message was still there . When I change to another channel I get a "no signal" message. I then power cycled the Box and tried to repeat this from BBC 2 and Discovery but i only had the "no signal" message from those channels.
Each time I power cycled the box, it rebooted to channel 402 ( sky sports 1 with my provider)
The factory reset is mentioned by scouser on another thread. What exactly is this and how do i perform it?
Any other ideas.?
Sorry if my message is a bit on the rambling side
Thanks
Minstralb
|
|
Advertisement
|
 |
|
|
AfterDawn Addict
|
19. November 2008 @ 07:26 |
Link to this message
|
Factory Reset.
Menu > Factory Setting
Pin - 0000
Press ok to Delete
TURN THE B0X OFF AT THE BACK FOR ONE MIN & THEN TURN BACK ON
English > installation
Choose provider
Auto scan > ok
channels found
Exit
Menu > 1570
Turn EMU on
Set Default key > press ok
Exit, Exit, Exit.
|
|
minstralb
Suspended due to non-functional email address
|
19. November 2008 @ 07:46 |
Link to this message
|
|
Thanks for the advice noely. I'll give it a try this evening and post back with any progress i make.
Cheers
|
|
minstralb
Suspended due to non-functional email address
|
19. November 2008 @ 13:58 |
Link to this message
|
|
i carried out the factory reset and I now have 24 channels. I think i will try another autoscan.
|
|
minstralb
Suspended due to non-functional email address
|
19. November 2008 @ 14:06 |
Link to this message
|
|
another autoscan has now brought me up to 172 channels. I seem to have most channels, so thanks again.
|
AfterDawn Addict
|
19. November 2008 @ 20:22 |
Link to this message
|
Originally posted by minstralb:
another autoscan has now brought me up to 172 channels. I seem to have most channels, so thanks again.
Well done mate, glad you got it sorted ;)
|
|
Kopster
Newbie
|
30. November 2008 @ 10:03 |
Link to this message
|
|
Guys I need help!
I have tried reseting to factory settings, ensured EMU is on, but Im still having problems. I get about 307 channels but can only view the free channels like BBC etc. The others, I keep getting the ' date is being updated'' and no matter how long I wait it doesnt work. It goes above 100% and then restarts.
Please help, I miss footy!
|
|
Advertisement
|
|
|
Moderator
|
30. November 2008 @ 10:10 |
Link to this message
|
Originally posted by Kopster:
Guys I need help!
I have tried reseting to factory settings, ensured EMU is on, but Im still having problems. I get about 307 channels but can only view the free channels like BBC etc. The others, I keep getting the ' date is being updated'' and no matter how long I wait it doesnt work. It goes above 100% and then restarts.
Please help, I miss footy!
Please help yourself by reading the fix that's just been added here - http://forums.afterdawn.com/thread_view.cfm/722659
Main PC ~ Intel C2Q Q6600 (G0 Stepping)/Gigabyte GA-EP45-DS3/2GB Crucial Ballistix PC2-8500/Zalman CNPS9700/Antec 900/Corsair HX 620W
Network ~ DD-WRT ~ 2node WDS-WPA2/AES ~ Buffalo WHR-G54S. 3node WPA2/AES ~ WRT54GS v6 (inc. WEP BSSID), WRT54G v2, WRT54G2 v1. *** Forum Rules *** |
