User User name Password  
   
Monday 20.1.2025 / 10:47
Search AfterDawn Forums:        In English   Suomeksi   På svenska
afterdawn.com > forums > archived forums > xbox - hardware mods > flashing a sharp tsop question
Show topics
 
Forums
Forums
Flashing A Sharp TSOP Question
  Jump to:
 
Posted Message
Junior Member
_
24. November 2008 @ 14:52 _ Link to this message    Send private message to this user   
I have a v1.1 xbox with a sharp tsop . And it has a X3CE modchip in it . I have been reading all day . This is what i have tried . http://www.xbox-linux.org/wiki/TSOP_flashing_HOWTO . When i boot up the xbox in MS mode it frags . What am i doing wrong ? Help Please ?

Servicing Southwest Michigans Broken And Modded Systems Since 2004 . Need Work Done ? Email Me . Peep My Systems . http://my.afterdawn.com/s10man/
Advertisement
_
__
varnull
Suspended permanently
_
24. November 2008 @ 20:49 _ Link to this message    Send private message to this user   
do you get an error on the screen?
Junior Member
_
24. November 2008 @ 20:53 _ Link to this message    Send private message to this user   
When It Boots From MS Mode (Chip Disabled) No . It Just Frags Then Kicks On My X3CE And Boots Up Off From That . Thanks For Your Help .

Servicing Southwest Michigans Broken And Modded Systems Since 2004 . Need Work Done ? Email Me . Peep My Systems . http://my.afterdawn.com/s10man/
varnull
Suspended permanently
_
24. November 2008 @ 21:09 _ Link to this message    Send private message to this user   
Just asking.. sometimes it will give you a clue what the problem is..

With the 1.1 you have a get out of jail free procedure.. it has 4 bios banks.. tizz wrote a guide on llamma.com about it :)

Junior Member
_
24. November 2008 @ 21:23 _ Link to this message    Send private message to this user   
Well ok , here is some info on this box . Relevant or not . It has 4817 bios on the tsop . From what i have found that is a 256k bios . correct ? So i am assuming that its 256k x 4 on the tsop . Correct ? If i flash the whole 1mb tsop with X2 4981.67 1mb would i be able to still later on (when i can afford a switch) be able to reflash it again with the X2 4981.67 512k and the 4817 256k x2 ? Or am i just confusing you ? Im very interested in splitting it in 2 . I just want to know that when the time comes i will be able to do the forementioned flash . If i am wrong then please by all means correct me . Thanks .

Servicing Southwest Michigans Broken And Modded Systems Since 2004 . Need Work Done ? Email Me . Peep My Systems . http://my.afterdawn.com/s10man/
varnull
Suspended permanently
_
24. November 2008 @ 21:46 _ Link to this message    Send private message to this user   
4 banks.. will only boot one or the other... flashing (or attempting to) with a larger that 256 bios will probably break it for good..

Not my thing.. never flashed a tsop.. never been brave enough. Everybody says leave well alone unless you are 100% sure what you are doing.. and I wasn't so I never tried.
Junior Member
_
24. November 2008 @ 22:05 _ Link to this message    Send private message to this user   
I have flashed other xboxes that had 256k tsops with success . My question is what am i doing wrong with this one ? Im still scratching my head . I would just like to know that i have the write points enabled for when i get a switch . Like i stated above i followed that tutorial with no success . I was told about undoing the top point and soldering wires to eachother . But i didnt understand what was explained . You seem like you can explain it to me . I thank you varnull for your help and support .

Servicing Southwest Michigans Broken And Modded Systems Since 2004 . Need Work Done ? Email Me . Peep My Systems . http://my.afterdawn.com/s10man/
varnull
Suspended permanently
_
25. November 2008 @ 08:25 _ Link to this message    Send private message to this user   
Your man is Tizz80 on llamma.com .. A quick search over there should reveal the info you need about the write_enable points. I know the 1.3 hynix tsop is flashable, but I'm not sure about the 1.1 :)
Junior Member
_
25. November 2008 @ 19:18 _ Link to this message    Send private message to this user   
Thanks for your help . i was able to figure it out .:)

Servicing Southwest Michigans Broken And Modded Systems Since 2004 . Need Work Done ? Email Me . Peep My Systems . http://my.afterdawn.com/s10man/
Advertisement
_
__
 
_
Junior Member
_
26. November 2008 @ 22:14 _ Link to this message    Send private message to this user   
i appreciate all the help i received here . These forums rock !!!! If anyone is interested in how i flashed my sharp tsop then let me know and i will post it . By the way i split my tsop in 2 with a switch . I totally love it . Again Thanks . :)

Servicing Southwest Michigans Broken And Modded Systems Since 2004 . Need Work Done ? Email Me . Peep My Systems . http://my.afterdawn.com/s10man/
afterdawn.com > forums > archived forums > xbox - hardware mods > flashing a sharp tsop question
 

Digital video: AfterDawn.com | AfterDawn Forums
Music: MP3Lizard.com
Gaming: Blasteroids.com | Blasteroids Forums | Compare game prices
Software: Software downloads
Blogs: User profile pages
RSS feeds: AfterDawn.com News | Software updates | AfterDawn Forums
International: AfterDawn in Finnish | AfterDawn in Swedish | AfterDawn in Norwegian | download.fi
Navigate: Search | Site map
About us: About AfterDawn Ltd | Advertise on our sites | Rules, Restrictions, Legal disclaimer & Privacy policy
Contact us: Send feedback | Contact our media sales team
 
  © 1999-2025 by AfterDawn Ltd.

  IDG TechNetwork