|
sv pvr western dig harddrive info needed
|
|
|
bellair
Junior Member
|
28. December 2008 @ 09:59 |
Link to this message
|
Got the box pvr here. When I go to format the disk I do not get PLAY on the receiver??. I went back, disassemabled the harddisk, How do I set it to master?. The jumper pin I presume is the little white connector, I tried following the explanation on the hard disk, and I still cannot get play to be displayed on the receiver.
Will someone please go through this with me.
Cheers,
|
|
Advertisement
|
|
|
|
Senior Member
|
28. December 2008 @ 11:10 |
Link to this message
|
Originally posted by bellair:
Got the box pvr here. When I go to format the disk I do not get PLAY on the receiver??. I went back, disassemabled the harddisk, How do I set it to master?. The jumper pin I presume is the little white connector, I tried following the explanation on the hard disk, and I still cannot get play to be displayed on the receiver.
Will someone please go through this with me.
Cheers,
Hi
Put 'How to format a hard drive' in the > 'Search messages' box at the top of the forum.
jbvid
|
|
bellair
Junior Member
|
28. December 2008 @ 11:59 |
Link to this message
|
|
jbvideo, cheers for the reply. I have done what you requested and after scrolling could not find advice for the novice. Looking for I guess for someone to hold my hand through this problem.
Cheers and thank you jbvideo.
|
Senior Member
|
28. December 2008 @ 14:10 |
Link to this message
|
Originally posted by bellair:
jbvideo, cheers for the reply. I have done what you requested and after scrolling could not find advice for the novice. Looking for I guess for someone to hold my hand through this problem.
Cheers and thank you jbvideo.
Hi
If you have the starview pvr (twin tuner) then on your hard drive there should be some drawings relating to the jumper pin and its master drive pin setting, if not goto the hard drives web site put in its model number and look for drive jumper pin settings and set the H/D to Master, fit it into the S/V PVR make sure red line on the ribbon cable goes next to 4 pin power plug. Run S/V software and format the drive from the PVR's menu system and wait for it to finish formatting, it will take a few minutes, you then need to record something onto it before it will play anything as it will be blank ie nothing at all on it after it format.
jbvid
|
|
bellair
Junior Member
|
28. December 2008 @ 15:28 |
Link to this message
|
|
One last question please, I have studied this and am still nervous of going wrong... Its a WD2500jb hard drive... it givess me 4 options.. (1)cable select setting (2) slave (3) master with slave present (4)single or master.
I know I will be up and running once I'm confident of making the right jumper setting. Please can you advise on this information.
Cheers.
|
Senior Member
|
28. December 2008 @ 15:42 |
Link to this message
|
Originally posted by bellair:
One last question please, I have studied this and am still nervous of going wrong... Its a WD2500jb hard drive... it givess me 4 options.. (1)cable select setting (2) slave (3) master with slave present (4)single or master.
I know I will be up and running once I'm confident of making the right jumper setting. Please can you advise on this information.
Cheers.
Hi
(4)Single or Master.
jbvid
|
|
bellair
Junior Member
|
28. December 2008 @ 15:45 |
Link to this message
|
|
Thank you very much, I'm learning all the time from this forum and you guys.
Cheers again.
|
|
Advertisement
|
|
|
Junior Member
|
6. January 2009 @ 08:01 |
Link to this message
|
Hi Bellair,
I've got a 500Gb WD on my SV PVR and 'Master' postion is with jumper removed.
Dont woory if you get the jumper wrong, it won't do any damage, it just won't work in that position.
Good luck.
Steve
|
