|
when flashing asks for ATAPI drive, help!!!!!!
|
|
|
alex957
Newbie
|
22. June 2009 @ 09:52 |
Link to this message
|
Hey i have a Benq drive that i am trying to flash. i was using iprep v9 and i used iXtreme 1.5. After i put it in boot-up type dBen and the serial number, then i turn the 360 on and press continue. I know the port number so i say N to the ones that are not it, when i find the port which is 0xDE00 and it says the the benq number then i press Y. But then it says something like "need ATAPI drive" when i put a number in it and enter it says wrong port.i have flashed a benq drive before but i have never seen anything like this before. I will take a pic of what is said to me and post it soon. But please i need help.
|
|
Advertisement
|
|
|
|
|
alex957
Newbie
|
22. June 2009 @ 10:30 |
Link to this message
|
|
im not sure if this is going to help but i just bought the system from this kid.
|
|
alex957
Newbie
|
22. June 2009 @ 11:35 |
Link to this message
|
|
it does read disks but not copyed one which means it has no firmwaare
|
AfterDawn Addict
3 product reviews
|
22. June 2009 @ 16:51 |
Link to this message
|
It does have firmware, just M$ original firmware.
Would suggest that you use Jungle Flasher & iExtreme 1.6 . Would highly suggest you do a hour or two's reading in this site before you start. There is however a tutorial included with Jungle Flasher.
To get instant assistance with Flashing / JTAG / Homebrew from experts for free! click me (Im not one of the said experts BTW)
Make poverty history, cheaper drugs NOW! |
|
alex957
Newbie
|
22. June 2009 @ 21:22 |
Link to this message
|
I installed jungle flasher 0.1.6beta and installed the Portio32.dll. Jungle flasher finds the drive and shows the following:
Drive Properties:
Vendor: PBDS
Name: VAD6038-64930C
But when i press Intro/Device ID
It Gives me a status of:
0x51
And sends me a error message with the following
MTK Vendor Intro Failed
If you wish to resend the command you should click Yes, Power off the drive and then back on (within 1 second).
And we tried that and it gives us the same result
I have flashed one BenQ drive before without any problems with the same chipset: Via VT6421A. so im not sure if it has gone bad or what am i doing wrong. Also the drive plays normal games just fine. HELP!!
|
AfterDawn Addict
2 product reviews
|
22. June 2009 @ 21:27 |
Link to this message
|
Originally posted by alex957:
I installed jungle flasher 0.1.6beta and installed the Portio32.dll. Jungle flasher finds the drive and shows the following:
Drive Properties:
Vendor: PBDS
Name: VAD6038-64930C
But when i press Intro/Device ID
It Gives me a status of:
0x51
And sends me a error message with the following
MTK Vendor Intro Failed
If you wish to resend the command you should click Yes, Power off the drive and then back on (within 1 second).
And we tried that and it gives us the same result
I have flashed one BenQ drive before without any problems with the same chipset: Via VT6421A. so im not sure if it has gone bad or what am i doing wrong. Also the drive plays normal games just fine. HELP!!
Keep trying to send the vendor info. You might have to remove the VIA driver to flash properly. As a last resort, you can boot DosFlash and I have a tutorial linked for it.
|
|
alex957
Newbie
|
23. June 2009 @ 12:57 |
Link to this message
|
|
I keep sending so i can get the info, but i have no luck. How do i remove the VIA driver?? because i have no clue how to do that. Also how do you boot DosFlash, could you give me that link for the tutorial so i could try that if the removal of the VIA driver does not work.
|
|
alex957
Newbie
|
23. June 2009 @ 13:11 |
Link to this message
|
|
I keep sending so i can get the info, but i have no luck. How do i remove the VIA driver?? because i have no clue how to do that. Also how do you boot DosFlash, could you give me that link for the tutorial so i could try that if the removal of the VIA driver does not work.
|
AfterDawn Addict
2 product reviews
|
23. June 2009 @ 13:14 |
Link to this message
|
|
1. Disable VIA card in Device Manager.
2. Go to C:\Windows\System32\drivers and remove "viamraid.sys" or "vsmraid.sys".
3. Re-enable VIA card in Device manager.
4. Re-boot.
|
|
alex957
Newbie
|
23. June 2009 @ 15:00 |
Link to this message
|
Originally posted by leerage:
1. Disable VIA card in Device Manager.
2. Go to C:\Windows\System32\drivers and remove "viamraid.sys" or "vsmraid.sys".
3. Re-enable VIA card in Device manager.
4. Re-boot.
How do u boot DosFlash becuase it did not work. I need help because i have no clue how to do it.
|
AfterDawn Addict
2 product reviews
|
23. June 2009 @ 15:15 |
Link to this message
|
I have a tutorial on how to make a bootable USB drive and how to use DosFlash16 linked in my signature.
|
|
alex957
Newbie
|
23. June 2009 @ 17:25 |
Link to this message
|
Originally posted by leerage:
I have a tutorial on how to make a bootable USB drive and how to use DosFlash16 linked in my signature.
can i see it please.
|
|
alex957
Newbie
|
23. June 2009 @ 18:19 |
Link to this message
|
Originally posted by leerage:
I have a tutorial on how to make a bootable USB drive and how to use DosFlash16 linked in my signature.
thank you, Ya i'm going to try that and see what happens.
|
|
alex957
Newbie
|
23. June 2009 @ 19:44 |
Link to this message
|
|
thanks i got it to work. thanx so much man!!!!!!!!!
|
|
Advertisement
|
|
|
AfterDawn Addict
2 product reviews
|
23. June 2009 @ 19:51 |
Link to this message
|
|
No problem. :)
Glad you got your drive flashed.
|
