|
|
|
Burning with Nero and Pioneer 107
|
|
|
carpki
Suspended due to non-functional email address
|
6. May 2004 @ 12:11 |
Link to this message
|
|
My Pioneer 107 started off burning + media and was doing well till I changed the media brand, then it steadfastly refused to burn to any type of media after that. I got an error at the end of the burn during the lead-out and it said the burn had failed! I have just built a new system and have now put the Pioneer in to it instead of my old system, and lo and behold it now burns again!!!
Hooray I here you say! Well not quite!, it now only burns to - media and refuses to burn to + media. When I burn to + media I get the same problem as before, also during the burn the buffer bar scoots about all over the place from 10% up to 90%. Any ideas what the problem is? Or am I missing the obvious somewhere!
|
|
Advertisement
|
|
|
|
AfterDawn Addict
|
6. May 2004 @ 17:31 |
Link to this message
|
|
Hi carpki, Your problem may be related to the brand of blank media you are using. What brand +R are you burning?
Also check if there is an update on your burner firmware.
Jerry
|
|
carpki
Suspended due to non-functional email address
|
6. May 2004 @ 23:37 |
Link to this message
|
|
Hi Jerry, thanks for replying! The +media in question is bulkpaq (no manufacturer i.d) and Mirror Platinum (manufacturer i.d. - IS01). The -media is Mirror Platinum Pro (manufacturer i.d. - RitekGo4). The firmare version is 1.09, which is the factory setting. I'm not really confident enough yet to go mucking about with the firmware as I really wouldn't be sure what I'm doing!
I have also heard people say to switch the DMA on, while others say to switch it off. Mine is switched off for that drive. Does that have anything to do with it?
Many thanks
Carpki
|
AfterDawn Addict
|
7. May 2004 @ 05:20 |
Link to this message
|
|
Have DMA enabled on all your drives. Having the burn fail on lead-out is usually an indication of bad media. The lead-out is the last thing that's written, so it's located at the outer edge of the disc. I would try a burn on something a bit smaller than 4464 MB, just to see if that's the problem.
If you are using Shrink, try reducing the size of the disc by 50 or 100 MB: Edit-> Preferences-> Target Disc Size-> change to custom and then change the target size.
As long as the buffer does not empty completely it should be OK. Enabling DMA may improve that.
|
|
carpki
Suspended due to non-functional email address
|
7. May 2004 @ 09:50 |
Link to this message
|
|
I've tried burning backups that are only about 3.3 Gb and i still get the same problem on +media, so they are nowhere near the edge of the disk when finishing. I will go and enable DMA just now to see if it makes a difference and try another disk. At least its burning to -media, better than not burning at all..lol :)
|
|
carpki
Suspended due to non-functional email address
|
7. May 2004 @ 14:35 |
Link to this message
|
|
DMA is now enabled and that cured the buffer level problem..it now stays constantly above 90% whilst burning to a CD+R but it still says it can't finish the disk. Still works okay on CD-R. Why does it refuse to burn to media that it was quite happy to burn to before? Jeez! I'm happy to continue burning to - media but this is doing my head in! I just want to know why this is a problem. Grrrrrrrrrrrr :(
|
AfterDawn Addict
|
7. May 2004 @ 16:01 |
Link to this message
|
You may want to upgrade the firmware to 1.10 (the latest) and see if that does anything, also sometimes removing and reinstalling your burning program will cure this. Especially Nero, which does not like to be moved around.
BTW, what are you using for burning software? Ripping software? What kinds of DVD programs do you have installed?
I use hacked firmware in my Pioneer A07. Both the official and hacked firmware are avalible here from flashman:
http://flashman.rpc-1.com/
Because you are having some issues, a firmware upgrade might be a good thing to do.
This message has been edited since posting. Last time this message was edited on 7. May 2004 @ 16:35
|
|
carpki
Suspended due to non-functional email address
|
7. May 2004 @ 16:22 |
Link to this message
|
Well I was using DVD X-Copy Platinum because I was being a bit lazy and new to it all. Its really simple to work. However I have just downloaded DVD Shrink and DVDEncrypter. I think I have sussed out DVD Shrink by following the guides on this forum, but emmmmm.. if u are familiar with DVD Shrink how do I delete the extras if I want to chuck them. It gives me an option to compress them, but I just don't want them at all. I'll look into the firmware thing tomorrow when I get out of bed.lol.
|
|
carpki
Suspended due to non-functional email address
|
7. May 2004 @ 16:27 |
Link to this message
|
|
In a quick reply to my last post, I've just had a look at the firmware site before I go to bed. Emmmmmmmmmmm I think I will have nightmares now and may not be able to get any sleep lol. I've heard about this and flashing, is it the same thing or seperate things? and will it hurt? lol.
|
AfterDawn Addict
|
7. May 2004 @ 17:09 |
Link to this message
|
It will void the warranty on your burner. I voided mine 15 minutes after installation. :D I installed the firmware that allows 6-8X burns with 4X -R media.
I thought it was causing problems so I reinstalled the original firmware. I did go back to the hacked firmware a while later.
Oriphus has a nice set of guides at his site, just browse for his site's URL in one of his post replys. Shouldn't be to hard to find as he gets around!
Other Shrink guides can be found here:
http://www.dvdshrink.info/guides.php
You have come to the right forum for help! There are lots of experts here with plenty of experence that really enjoy helping folks out.
As far as removing stuff with Shrink, you will lose the menu, so just bear that in mind. Select Reauthor once the analysis is complete, then drag the main title into the compilation window on the left. While you are at it, get rid of the un-needed audio and subpictures as well. When you are done, select backup! From the menu that opens, select ISO disc image and check the box below that to enable burning with Decrypter. Put your disc in your burner and select OK. Shrink will do the rest. You don't need to open Decrypter, Shrink just uses Decrypter's burn engine as long as you have the settings correct.
|
|
baboo
Junior Member
|
8. May 2004 @ 03:55 |
Link to this message
|
If you are using Nero ultra 6 , you should down load the four updates I had a problem of not finishing burning and the updates fixed it for me.
Baboo
|
|
carpki
Suspended due to non-functional email address
|
8. May 2004 @ 09:00 |
Link to this message
|
Thanks for pointing me in the direction of the guides (Fastfrank) I seem to have sussed out DVD Shrink already. I'll leave the firmware till I'm more comfortable with the idea of doing it. I'll also leave the downloading of Nero updates till broadband lands here in less than two months (allegedly). But thanks for the idea Baboo. I think I'll just continue to burn to -media at the moment!
|
|
Clotty
Newbie
|
8. May 2004 @ 10:19 |
Link to this message
|
|
I'm a total newbie when it come to DVD writers, but I flashed my Pioneer 107 with the 1.13 firmware from the pioneer site. It scared the C**P out of me as I'd never done this before to any of my cd writers, but It seems to have sorted out my problem with 4 speed writing. All the best
|
AfterDawn Addict
|
8. May 2004 @ 14:25 |
Link to this message
|
|
Hi Clottie,
Flashing is pretty exciting the first few times. As long as no fire comes out the front of your PC its probably going to work.
|
|
carpki
Suspended due to non-functional email address
|
8. May 2004 @ 14:32 |
Link to this message
|
|
Fire??? Oh jeez!! now u put me off totally lmao.
I actually downloaded the offical firmware update and it said to follow the instructions in read-me to a tee. Problem was there is no read me file. So I downloaded an unoffical one which makes it region free etc. It did have a read-me document but it only told me what the new firmware version would do!! not how to do it!!
Could I ask a favour and be pointed in the right direction where I could get some instructions to all this. iIt would be much appreciated
|
Senior Member
|
8. May 2004 @ 16:06 |
Link to this message
|
|
I use to have a pioneer burner and when i started updateing the firmware this is when i had problems.Stick with the firmware you have got until you have checked the other firmware updates out 100% and your sure it is really worth updateing and make sure it is one you can change back.As there was one i updated and could not go back.Bulkpak media is ok as such but you do get some faulty spindles from time to time i have had a few 25 packs of this media where all were faulty.Try the yellow daterwrite they are cheap and i have never had a problem with them.The grey ones of the same brand are even better but i would stay away from the red ones of the same brand as i have problems with them.Best thing for you to do is trial and error go to a computer fair and buy a load of single discs of different types and use trial and error.You can use pioneer web site which gives you a guide to performance of each media for your drive but this is not always true to your drive
i9 9900K CPU,ASUS MAXIMUS XI HERO Mobo, Fractal R6 Case,
Corsair H115I ,Corsair RM Series 850W psu,
RTX 3080 Ti ,Corsair DDR4 Vengeance RGB PRO 32GB 1TB Intel SSD 660p Series,1TB M.2 ,36TB Seagate HD,19TB Ext, LG BH16NS40 BD-RW,Creative Sound Blaster Zx 116dB Sound Card, Acer Predator XB321HK 32inch 4K Monitor, 2TB PS4
|
|
carpki
Suspended due to non-functional email address
|
9. May 2004 @ 00:25 |
Link to this message
|
|
Cheers John! Go to a computer fair??? Jeez! we just got electricity!! I'm afraid a round trip to the nearest one would take over 7 hours. I do have a local supplier where I get my stuff from tho, and they're not to bad price wise, but limited choice wise. I tried bulkpaq and put them in the bin, the -media that I use is RitekG04 which costs £14.99 for 25 which isn't too bad. I am thinking of getting an nec2500a as well cause they only cost £59. But your right! I think I'll stick with the firmware I have got for the meantime
|
Senior Member
|
9. May 2004 @ 06:41 |
Link to this message
|
|
Check out the web for some really good priced media which you can get shipped out to you.I think there is one called disc city or something like that and they were real value for money £8 for 25 daterwrite.Put a search in for media sites on googles and you will get some good deals.
i9 9900K CPU,ASUS MAXIMUS XI HERO Mobo, Fractal R6 Case,
Corsair H115I ,Corsair RM Series 850W psu,
RTX 3080 Ti ,Corsair DDR4 Vengeance RGB PRO 32GB 1TB Intel SSD 660p Series,1TB M.2 ,36TB Seagate HD,19TB Ext, LG BH16NS40 BD-RW,Creative Sound Blaster Zx 116dB Sound Card, Acer Predator XB321HK 32inch 4K Monitor, 2TB PS4
|
|
kaledrr
Member
|
9. May 2004 @ 19:47 |
Link to this message
|
I have the same problem, I burned about 16 Maxell dvd+r but latter it start to fial. It mention prcess failed at 4x.
i have the Nero 6.3 and pioneer DVR-107d.
|
|
kaledrr
Member
|
9. May 2004 @ 19:57 |
Link to this message
|
|
he I just used sony DVD+RW to burn some files and worked fine, but when I use to burn files usning Maxell dvd+r it failed.
|
|
kaledrr
Member
|
9. May 2004 @ 23:39 |
Link to this message
|
|
I tried again to burn, but failed. I saved the log here it is, if any one can help
Windows XP 5.1
IA32
WinAspi: -
ahead WinASPI: File 'C:\Program Files\Ahead\nero\Wnaspi32.dll': Ver=2.0.1.56, size=163910 bytes, created 4/2/2003 8:13:44 AM
Nero version: 6.0.0.0 (Nero Express)
Recorder: <PIONEER DVD-RW DVR-107D>Version: 1.13 - HA 1 TA 1 - 6.0.0.0
Adapter driver: <atapi> HA 1
Drive buffer : 2000kB
Bus Type : via Inquiry data (1) -> ATAPI, detected: ATAPI
Connected to MMC as unknown drive with class-nr : 1
Drive is autodetected - recorder class: Std. MMC recorder
CD-ROM: <IDE DVD-ROM 16X >Version: 2.50 - HA 1 TA 0 - 6.0.0.0
Adapter driver: <atapi> HA 1
=== Scsi-Device-Map ===
DiskPeripheral : WDC WD800BB-00CAA1 atapi Port 0 ID 0 DMA: On
DiskPeripheral : WDC WD800BB-00CJA1 atapi Port 0 ID 1 DMA: On
CdRomPeripheral : IDE DVD-ROM 16X atapi Port 1 ID 0 DMA: On
CdRomPeripheral : PIONEER DVD-RW DVR-107D atapi Port 1 ID 1 DMA: On
=======================
AutoRun : 1
Excluded drive IDs:
CmdQueuing : 1
CmdNotification: 2
WriteBufferSize: 83886080 (0) Byte
ShowDrvBufStat : 0
EraseSpeed : 0
BUFE : 0
Physical memory : 1022MB (1047276kB)
Free physical memory: 278MB (285408kB)
Memory in use : 72 %
Uncached PFiles: 0x0
Use Static Write Speed Table: 0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)
9.5.2004
ISO compilation
11:28:49 PM #1 Text 0 File Isodoc.cpp, Line 5451
Iso document burn settings
------------------------------------------
Determine maximum speed : FALSE
Simulate : FALSE
Write : TRUE
Finalize CD : FALSE
Multisession : TRUE
Multisession type: : Start multisession
Burning mode : DAO
Mode : 1
ISO Level : 1 (Max. of 11 = 8 + 3 char)
Character set : ISO 9660
Joliet : TRUE
Allow pathdepth more than 8 directories : TRUE
Allow more than 255 characters in path : TRUE
Write ISO9660 ;1 file extensions : TRUE
11:28:49 PM #2 Text 0 File Reader.cpp, Line 118
Reader running
11:28:49 PM #3 Text 0 File Writer.cpp, Line 127
Writer PIONEER DVD-RW DVR-107D running
11:28:49 PM #4 ISO9660GEN -11 File geniso.cpp, Line 3814
First writeable address = 0 (0x00000000)
11:28:49 PM #5 Text 0 File Burncd.cpp, Line 3081
Turn on Disc-at-once, using DVD media
11:28:50 PM #6 Text 0 File DlgWaitCD.cpp, Line 224
Last possible write address on media: 2295103 (510:01.28)
Last address to be written: 2115615 (470:08.15)
11:28:50 PM #7 Text 0 File DlgWaitCD.cpp, Line 229
Write in overburning mode: FALSE
11:28:50 PM #8 Text 0 File DlgWaitCD.cpp, Line 1688
Recorder: PIONEER DVD-RW DVR-107D, Media type: DVD+R
Disc Manufacturer ID: RICOHJPN, Media Type ID: R01, Product revision number: 2
Disc Application Code: 0, Extended Information Indicators: 1
11:28:50 PM #9 Text 0 File ThreadedTransferInterface.cpp, Line 757
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 (CTransferItem)
2 indices, index0 (150) not provided
original CD pos #0 + 2115616 (2115616) = #2115616/470:8.16
relocatable, CD pos for caching/writing not required/required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2115616 blocks [PIONEER DVD-RW DVR-107D]
--------------------------------------------------------------
11:28:50 PM #10 Text 0 File Burncd.cpp, Line 3318
Recorder and media-info
=======================
Burning to PIONEER DVD-RW DVR-107D on a DVD+R media
11:28:59 PM #11 Text 0 File ThreadedTransferInterface.cpp, Line 910
Prepare recorder PIONEER DVD-RW DVR-107D for write in cue-sheet-DAO
DAO infos:
==========
MCN:
TOCTYPE: 0x0 Session Closed, CD not fixated
Tracks 1 to 1:
TRM_DATA_MODE1, 2048/0x0, ISRC "", FilePos 0 307200 38121472
11:28:59 PM #12 Phase 24 File dlgbrnst.cpp, Line 1818
Caching of files started
11:28:59 PM #13 Phase 25 File dlgbrnst.cpp, Line 1818
Caching of files completed
11:29:00 PM #14 Phase 36 File dlgbrnst.cpp, Line 1818
Burn process started at 4x (5,520 KB/s)
11:29:00 PM #15 Text 0 File ThreadedTransferInterface.cpp, Line 2104
Verifying CD position of item 0 (relocatable, CD pos, no patch infos, orig at #0): write at #0
11:29:00 PM #16 Text 0 File Cdrdrv.cpp, Line 7827
---- DVD Structure: Physical Format Information (00h) ----
Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD+R (10), Part Version: 1
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 26053F h
End Sector Number in Layer 0: 0 h
Data in Burst Cutting Area (BCA) does not exist
Media Specific:
00 01 52 49 43 4F 48 4A - 50 4E 52 30 31 02 38 23 ..RICOHJPNR01.8#
54 37 09 00 3C 67 00 AC - 62 16 18 0B 0B 0A 0B 01 T7..<g..b.......
19 1B 0B 0B 0E 0F 01 00 - 00 00 00 00 00 00 00 01 ................
11:29:00 PM #17 Text 0 File dlgbrnst.cpp, Line 1678
Set remaining time: 13:18,982 (798982ms) -> OK
11:29:00 PM #18 Text 0 File DVDPlusRW.cpp, Line 513
Start write address at LBA 0
DVD high compatibility mode: Yes
11:29:02 PM #19 Text 0 File Writer.cpp, Line 318
23:29:02.968 - PIONEER DVD-RW DVR-107D : Queue again later (Intervall : 11msec)
11:29:34 PM #20 Text 0 File Writer.cpp, Line 318
23:29:34.281 - PIONEER DVD-RW DVR-107D : Queue again later (Intervall : 11msec)
11:42:33 PM #21 Text 0 File WriterStatus.cpp, Line 112
<PIONEER DVD-RW DVR-107D> start writing Lead-Out at LBA 2115616 (204820h), lenght 0 blocks
11:42:33 PM #22 Text 0 File ThreadedTransfer.cpp, Line 227
all writers idle, stopping conversion
11:42:34 PM #23 SCSI -1066 File Cdrdrv.cpp, Line 1151
SCSI Exec, HA 1, TA 1, LUN 0
Status: 0x04 (0x01, SCSI_ERR)
HA-Status 0x00 (0x00, OK)
TA-Status 0x02 (0x01, SCSI_TASTATUS_CHKCOND)
Sense Key: 0x05 (KEY_ILLEGAL_REQUEST)
Sense Code: 0x24
Sense Qual: 0x00
CDB Data: 0x5B 0x01 0x01 0x00 0x00 0xFF 0x00 0x00 0x00 0x00 0x00 0x00
Sense Data: 0x70 0x00 0x05 0x00 0x00 0x00 0x00 0x0E
0x00 0x00 0x00 0x00 0x24 0x00
11:42:34 PM #24 SCSI -1176 File Cdrdrv.cpp, Line 1151
SCSI Exec, HA 1, TA 1, LUN 0
Status: 0x04 (0x01, SCSI_ERR)
HA-Status 0x00 (0x00, OK)
TA-Status 0x02 (0x01, SCSI_TASTATUS_CHKCOND)
Sense Key: 0x05 (KEY_ILLEGAL_REQUEST)
Sense Code: 0x72
Sense Qual: 0x03
CDB Data: 0x5B 0x01 0x02 0x00 0x00 0xFF 0x00 0x00 0x00 0x00 0x00 0x00
Sense Data: 0x70 0x00 0x05 0x00 0x00 0x00 0x00 0x0E
0x00 0x00 0x00 0x00 0x72 0x03
11:42:34 PM #25 Text 0 File dlgbrnst.cpp, Line 1678
Set remaining time: 0:00,000 (0ms) -> OK
11:42:34 PM #26 CDR -1066 File ThreadedTransferInterface.cpp, Line 1594
Invalid field in command
11:42:34 PM #27 TRANSFER -24 File ThreadedTransferInterface.cpp, Line 1594
Could not perform end of Disc-at-once
11:42:34 PM #28 Text 0 File dlgbrnst.cpp, Line 1678
Set remaining time: 0:00,000 (0ms) -> OK
11:42:34 PM #29 Text 0 File dlgbrnst.cpp, Line 1678
Set remaining time: 0:00,000 (0ms) -> OK
11:42:34 PM #30 Phase 38 File dlgbrnst.cpp, Line 1818
Burn process failed at 4x (5,520 KB/s)
Existing drivers:
File 'Drivers\atapi.sys': Ver=5.1.2600.1106 (xpsp1.020828-1920), size=86912 bytes, created 8/29/2002 1:27:50 AM (Adapter driver for rec)
Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
This message has been edited since posting. Last time this message was edited on 11. May 2004 @ 17:57
|
|
carpki
Suspended due to non-functional email address
|
10. May 2004 @ 00:27 |
Link to this message
|
I'm of the opinion that my Pioneer 107 is nothing but a snob!!!
It works quite happily with what its got, but if you give it a taste of something better ( i.e. more expensive media), it refuses to go back to what it had.
Your error log look prety much identical to mine, with the same errors reporting. I have tried everything apart from updating the firmware (which I'm reluctant to do) and updating Nero (I have version 6.0, but I see u have 6.3 and its doing the same, so no point in me spending hours on my dial-up upgrading!).
I took mine back to the shop after a friend had the same problem and they replaced his with no questions asked. However, they refused to replace mine and kept it for 4 days to test it. I got it back and they gave me some test disks that they had burnt and said it worked fine. The test disks certainly did work, but they were not + media, which is where my problem is!
I even built a new computer and put it in there, but I still get problems with it.
I'm just going to give up on it and keep burning to - media.
I see that yours is also tempermental when it comes to media and thats just maybe where the problem lies!
|
AfterDawn Addict
|
10. May 2004 @ 18:29 |
Link to this message
|
hi Guys,
When you include your Nero Logfile try not to include your registration code! Kaledrr, You really should edit that outa there before everyone owns your program.
Things I noticed:
Nero version: 6.0.0.0 (Nero Express)
Physical memory : 1022MB (1047276kB)
Free physical memory: 278MB (285408kB)
Memory in use : 72 %
Multisession : TRUE
Multisession type: : Start multisession
Burning mode : DAO
Mode : 1
ISO Level : 1 (Max. of 11 = 8 + 3 char)
Character set : ISO 9660
Joliet : TRUE
Allow pathdepth more than 8 directories : TRUE
Allow more than 255 characters in path : TRUE
Write ISO9660 ;1 file extensions : TRUE
First item, the newest version of Nero Express is 6.3.1.10
Memory usage: Just looks like your using quite a bit of your RAM during the process. I think I stay around 30 to 40% when I'm burning.
Now I am burning DVD movies so yours may be correct, however my successful A-07 burn logs look a bit different. I never relax Joliet Restrictions or attempt to burn a multisession DVD.
I always use Nero Burning ROM in the DVD-Video mode.
Multisession should be FALSE
Joliet Should be FALSE
Allow pathdepth more than....Should be FALSE
Allow more than 255 characters...Should be FALSE
Did you notice where the process failed?
"Could not perform end of Disc-at-once"
This may have something to do with having "multisession" enabled.
There have been at least one major revision and a few minor ones since this version was released. You should update your program.
All the problems that I had with my A-07 were all Nero related. A removal and reinstallation of the program solved my issues and now my Pioneer works fast and flawlessly.
|
|
kaledrr
Member
|
11. May 2004 @ 17:38 |
Link to this message
|
|
I just noticed something, The drvier is listed as
Pioneer DVR-RW DVR-A07, in the dvice manger. it used to be Pioneer DVR+RW DVR-A07. I do not know why it changed it is setting and how to change it back?
|
|
Advertisement
|
|
|
AfterDawn Addict
|
11. May 2004 @ 17:44 |
Link to this message
|
|
kaledrr, Your Nero registration number is still in your "Nero Log" post. You really should go and edit that post and get that out of there unless you want everyone to have your number.
Mine says exactly what yours says with no problems.
This message has been edited since posting. Last time this message was edited on 11. May 2004 @ 17:50
|
|
