|
modchip for older xbox
|
|
|
againstme
Newbie
|
9. May 2004 @ 17:47 |
Link to this message
|
|
i have an xbox with solder in the lpc holes, can i still use the xecuter solderless chip or do i have to buy a new chip or scrap out the solder?
brandon
|
|
Advertisement
|
 |
|
|
|
scottas
Suspended due to non-functional email address
|
9. May 2004 @ 19:51 |
Link to this message
|
|
Radio $hack or likeness sells a desolder tool. It allows you to heat up the solder and then suck it out of the hole. I used an extra nose bulb (for those of you with kids) on one side and my iron on the other. Worked pretty good. It was 2am and I was modding a 1.0 box. I like the header pin myself. Makes swapping chips easy. Oh yeah, the bulb is in my toolbox now not the drawer.
ver 1.0, 1.5 and 1.6 with 200gb hdds & X3. Team Xecuter Pro front panel with LCD Screen (rocks). GC with qoob pro, Team xecuter's iced cube case mod and a BBA.
|
Senior Member
|
10. May 2004 @ 06:02 |
Link to this message
|
|
I used a drill with a number 1 drill bit.
You are reading a mindless signature, please stop reading it now it is mindless, one can only presume you are mindless since you are still reading this mindless signature, Oh my god get a life you mindless person, whats the matter with you, dont you have a girlfreind? mindless mindless mindless
|
|
againstme
Newbie
|
10. May 2004 @ 10:48 |
Link to this message
|
|
but will the chip still work with the soler still there or do i have to remove the solder?
brandon
|
|
ten80
Junior Member
|
10. May 2004 @ 11:13 |
Link to this message
|
|
I just installed a new Xecuter lite [+] on my friends 1.0v xbox...the original one with solder inside the lpc holes and I didn't remove them at all(mainly cause I couldn't find my soldering iron). But I had no problem with it. As long as your alignment of the chip is good and secure then there's no prob. Just remember to remove the lacquer with a fiber glass pen from the D0 point.
-------------
Xbox - S-Controllers
X-ecuter2.3b lite [+]
Xecuter bios
Western Digital 7200rpm 120gb HD
|
|
ten80
Junior Member
|
10. May 2004 @ 11:15 |
Link to this message
|
Quote:
I used a drill with a number 1 drill bit
DUDE...thats ballsy. You must have a steady hand.
-------------
Xbox - S-Controllers
X-ecuter2.3b lite [+]
Xecuter bios
Western Digital 7200rpm 120gb HD
|
|
againstme
Newbie
|
10. May 2004 @ 13:07 |
Link to this message
|
|
where do you get the fibre glass pen? is there a guide showing how to remove the laquer?
brandon
|
|
ten80
Junior Member
|
10. May 2004 @ 13:11 |
Link to this message
|
-------------
Xbox - S-Controllers
X-ecuter2.3b lite [+]
Xecuter bios
Western Digital 7200rpm 120gb HD
|
|
againstme
Newbie
|
10. May 2004 @ 13:19 |
Link to this message
|
|
if you buy a chip that isnt flashed? how do you flash it and then install evox? i have a mac.
brandon
|
|
againstme
Newbie
|
10. May 2004 @ 19:30 |
Link to this message
|
|
will the chip still work if you dont scrape off the laquer?
brandon
|
Senior Member
|
11. May 2004 @ 00:01 |
Link to this message
|
|
I actually fill the LPC holes with solder on the newer xbox's , gets a better connection
XB360 hitachi xtreme f/ware, chameleon case, whisper & airflow blue led. XBOX w/ 2.6 2x custom "djboogie" bios. PSP 1.50 w/ devhook .52 % 303 f/ware.
|
Senior Member
|
11. May 2004 @ 00:03 |
Link to this message
|
|
for good chip connection, make the screw hole slighly wider, it allows for better connection not just for the LPC area but the d0
XB360 hitachi xtreme f/ware, chameleon case, whisper & airflow blue led. XBOX w/ 2.6 2x custom "djboogie" bios. PSP 1.50 w/ devhook .52 % 303 f/ware.
|
|
againstme
Newbie
|
11. May 2004 @ 13:19 |
Link to this message
|
|
will the solderless executer chip still work if i dont scrape off the laquer of the d0 point?
brandon
|
|
ten80
Junior Member
|
11. May 2004 @ 17:20 |
Link to this message
|
Quote:
will the solderless executer chip still work if i dont scrape off the laquer of the d0 point?
No....you need to make a good connection between the d0 copper and the pogo point onthe chip which is also copper. electrical currents don't conduct through plastics. So you need to scrpe it off.
-------------
Xbox - S-Controllers
X-ecuter2.3b lite [+]
Xecuter bios
Western Digital 7200rpm 120gb HD
|
|
againstme
Newbie
|
11. May 2004 @ 17:33 |
Link to this message
|
|
how exactly do you scrape it off? ive seen the guide at teamexectuer.com but it just shows before and after. i need to know exactly how to do it and where around the d0 point.
brandon
|
|
Advertisement
|
|
|
Senior Member
|
12. May 2004 @ 09:40 |
Link to this message
|
just shove the fibre glass pen on and scrach:)
Quote:
DUDE...thats ballsy. You must have a steady hand.
heh yeah... but i have done a few, not lite+ tho just plain old lite with solder
You are reading a mindless signature, please stop reading it now it is mindless, one can only presume you are mindless since you are still reading this mindless signature, Oh my god get a life you mindless person, whats the matter with you, dont you have a girlfreind? mindless mindless mindless
|
