|
Bent & Beat Up CPU
|
|
|
jo15765
Newbie
|
27. February 2014 @ 22:15 |
Link to this message
|
|
I am getting RROD and the secondary error code of 0022. I literally JUST had the CPU & GPU replaced roughly 10 days ago. Could they just be faulty, and I should replace both of them, or could it be bc the CPU heatsink looks like someone wasn't careful when it was installed and a screwdriver or something slid between a few of the shafts.
|
|
Advertisement
|
|
|
|
|
richietea
Member
|
28. February 2014 @ 04:10 |
Link to this message
|
|
0022 Error code refers to the gpu overheating,Try turning the screws in small increments on the heatsinks as the may be too tight and not displacing heat properly.
|
|
jo15765
Newbie
|
28. February 2014 @ 08:01 |
Link to this message
|
Originally posted by richietea:
0022 Error code refers to the gpu overheating,Try turning the screws in small increments on the heatsinks as the may be too tight and not displacing heat properly.
How "tight" should the screws be? I.E. How do I know when too loose is?
|
|
richietea
Member
|
28. February 2014 @ 12:05 |
Link to this message
|
|
Trial and error.Some people make the mistake of been too tight not letting the thermal compound do its job properly also bending/warping the board.
|
Senior Member
|
28. February 2014 @ 12:45 |
Link to this message
|
Originally posted by jo15765:
Originally posted by richietea:
0022 Error code refers to the gpu overheating,Try turning the screws in small increments on the heatsinks as the may be too tight and not displacing heat properly.
How "tight" should the screws be? I.E. How do I know when too loose is?
apparently hard drive screws require a specific torque setting done with a torque screw driver,do a google search and see if the gpu is the same.
actually not sure how much a torque screwdriver would costs,i've only used a torque wrench on cars myself.
custom built gaming pc from early 2010,ps2 with 15 games all original,ps3 500gbs with 5 games all original,yamaha amp and 5.1channel surround sound speakers,46inch sony lcd smart tv.
|
|
jo15765
Newbie
|
28. February 2014 @ 18:57 |
Link to this message
|
|
I loosened the screws and now am getting an error code of 0102. What does this one mean and what to do to fix it?
|
|
ddp
Moderator
|
28. February 2014 @ 21:25 |
Link to this message
|
|
|
|
richietea
Member
|
1. March 2014 @ 04:45 |
Link to this message
|
|
If you are you getting the secondary error code 0102 it could be related to the southbridge area of the mobo but there is contention between this and cold solder joints.Most people try to do a reflow but end up using a heatgun and melting components due to timing and displacement of the heat from the gun.Some people do the oven trick and bake the mobo to repair cold/cracked solder.Some work,some don't.I cannot guarantee the success rate of either or recommend.It is entirely at your desecration.But i would research all options first.
|
|
jo15765
Newbie
|
1. March 2014 @ 10:39 |
Link to this message
|
Originally posted by richietea:
If you are you getting the secondary error code 0102 it could be related to the southbridge area of the mobo but there is contention between this and cold solder joints.Most people try to do a reflow but end up using a heatgun and melting components due to timing and displacement of the heat from the gun.Some people do the oven trick and bake the mobo to repair cold/cracked solder.Some work,some don't.I cannot guarantee the success rate of either or recommend.It is entirely at your desecration.But i would research all options first.
I didn't realize how in depth/difficult it is to reflow/replace the Southbridge. Would I be better off just getting a new/used XBOX 360?
This message has been edited since posting. Last time this message was edited on 1. March 2014 @ 11:00
|
AfterDawn Addict
|
1. March 2014 @ 11:17 |
Link to this message
|
|
Would I be better off just getting a new/used XBOX 360?
Yes. I would say the reballing wasn't very successful in the first place, so just get a used working Xbox 360.
Xbox 360: Slim untouched with a faked 320 GB harddrive for XBL, phat with LT 3.0, played Halo early, so going on live would be an instand ban, also with a faked 320 GB harddrive
PS3: Untouched 160 GB Slim, 60 GB Fat with latest Rogero and 160 GB internal harddrive.
PSVita: hardly ever play it
GameCube: Black with a Viper chip installed. With gameboy player. Trying to get a Wavebird controller.
|
|
Advertisement
|
|
|
|
jo15765
Newbie
|
1. March 2014 @ 13:13 |
Link to this message
|
Originally posted by Eisherz:
Would I be better off just getting a new/used XBOX 360?
Yes. I would say the reballing wasn't very successful in the first place, so just get a used working Xbox 360.
Thanks for the tip. I will look for a used working one.
One afterthought I just did a XClamp repair kit & cleaned chips etc etc. Now (the xbox is still disassembled at this point) when I plug in the power chord and turn on, the center light just flashes. I never get the 4 Green lights, nor do I get a Red Ring sequence.
What could this mean?
EDIT--
And by disassembled I mean the power chord into the back of the mobo and the on/off button plugged into the mobo NOTHING else attached.
This message has been edited since posting. Last time this message was edited on 1. March 2014 @ 13:18
|
