|
OHMS ? AMPS !!? SPEAKERS !!!??
|
|
|
ThELiZ
Newbie
|
6. May 2007 @ 15:18 |
Link to this message
|
|
cheers gerry. and just for the record i am a guy, one who knows very little about ohms! lol. I think i should stick to what i know, computers. :)
Can't wait to get my system up and running.
|
|
Advertisement
|
 |
|
|
|
gerry1
Suspended permanently
|
6. May 2007 @ 15:41 |
Link to this message
|
|
It's like JVC said ... two ohms won't make a difference ... well, not much anyway. Just make sure your receiver is in a more open space; ventilation is important because the 6 ohm might make it put out a little more heat but in no way is it hot enough to damage the receiver; just don't put it in a place that's all boxed in.
@JVC ,,, how are my friend?
|
Senior Member
|
6. May 2007 @ 18:40 |
Link to this message
|
|
Hey gerry........
Ok here. Just hanging in there. :o)
|
|
ThELiZ
Newbie
|
7. May 2007 @ 02:19 |
Link to this message
|
|
Thanks for the replies. Good job i posted because i was going to stack the cd player on top of the receiver. Now i know to keep it well ventilated.
Cheers.
|
|
gerry1
Suspended permanently
|
7. May 2007 @ 04:11 |
Link to this message
|
|
@wilbow and theliz ... it NEVER a good idea to put something on your receiver and check your DVD player also, some of them (not all) also put out heat.
|
|
Wilbow
Suspended due to non-functional email address
|
7. May 2007 @ 12:39 |
Link to this message
|
|
Hi all,
glad my thread is generating a bit of interest, I have just won a bag of capacitors for 99p off ebay, so if I'm lucky there will be a couple of what I need. I quite like soldering so no problem there, its just if the circuit board is goosed it'll all be a waste of time.
I know about the heat dissapation thing, I bought a big black glass stand to go with the setup, I got plenty of room around the amp, the PS3 also blows out quite a bit of heat too.
The guy who sold me the amp claims it was working ok when he sent it, so no joy there.
Cheerio for now.
Devotee
|
|
Wilbow
Suspended due to non-functional email address
|
20. May 2007 @ 11:26 |
Link to this message
|
|
Hi guys, I have given up on the Marantz amp, getting hold of some of the large capacitors that I think are bust is hard. Still trying to get my money back for it.
So I splashed out on a new Sony one, the one I mentioned earlier. Its superb, coupled with the PS3 and the Mission speakers their superb too, watched 'Deja Vu' in bluray on it last night, brilliant.
Cheerio for now.
Devotee
|
|
gerry1
Suspended permanently
|
20. May 2007 @ 11:32 |
Link to this message
|
|
@Wilbow....congratulations! It's nice to listen to music or watch movies on a system that works properly, isn't it? One doesn't get enough relaxation in this world; you might as well get the most out of it!
|
|
genus67
Newbie
|
23. May 2007 @ 23:39 |
Link to this message
|
Manuals are really helpful; though sometimes, they are hard to understand and we need a person to explain things to us. You should be thankful to gerry1, Wilbow. :D
________________
Mike
McIntosh MX135 Audio/Video Control Center - Download the MX135 Audio/Video Control Center Catalog by McIntosh Laboratory, Inc.
|
|
techquest
Newbie
|
24. May 2007 @ 00:28 |
Link to this message
|
|
Hi Wilbow
I'm a newbie to this site but not to electronics and amps etc.
Got to see the pics you posted and the items could very well be disc type caps, but there are other electornic components that look much the same, and possibly an axial type cap, difficult to see it though as it appears blown. They look as though they are around a bridge rectifier which forms part of the power supply. They could just be decoupling & filter caps or there abouts. The issue is these items are not that difficult to get a hold of. You just need to identify them, they might have markings still visible, or from a circuit diagram. The components in question should have the individual componet id's on the PCB, since the diodes, for instance, are clearly marked.
That aside it looks to me from the state of the PCB, as far as I can make out from the pics, that it has been subjected to damage caused by some sort of fluid spillage or moisture.
Little wonder the eBayer has vanished, all the way to the pub me thinks!
Anyway if I can help at all I will.
Cheers
|
|
Wilbow
Suspended due to non-functional email address
|
27. May 2007 @ 10:51 |
Link to this message
|
|
Hi Techquest,
Thanks for taking an interest, I replaced the burnt out small caps but the amp still switched off. There are two large capacitors that I think are faulty also, there is white goo at the bottom of them that i thought was just adhesive at first, now I'm not so sure. I have found some large capacitors on ebay that are the same rating ( 63v 15000uF), but they are double the size, I dont now whether to gamble on them or just quit now and not throw good money on bad.
Cheerio for now
Devotee
This message has been edited since posting. Last time this message was edited on 27. May 2007 @ 10:52
|
|
gerry1
Suspended permanently
|
27. May 2007 @ 15:43 |
Link to this message
|
|
@genus67 and techquest ... welcome to afterdawn guys! There are a lot of really nice people here as well as some really knowledgable ones. There is plenty to learn on any number of topics and if you have knowledge in a particular subject, help is always appreciated for those asking questions. When I first came here, I didn't know squat but I learnt an aweful lot and now enjoy sharing what I've learnt depending on how much time I have. We help out in the forums after which, many of us go to the "safety valve" were we just talk about specific topics or just play and joke around. Techquest, if you choose to stick around, your electronis knowledge will be invaluable.
@Wilbow ... how are you my friend? You're still happy with the new system I hope? There is always a lot to learn when you get a new AVR. You know, there is one thing I think I forgot to mention. With a lot of AVRs, you have to manually activate the microprocessors to really appreciate the features of the amp. Its amazing how many people don't even realize it; because their system sounds so good they aren't even aware that their system and the effects aren't performing as they should. Genus67 is right about manuals ... sometimes they're difficult to understand but they're ALWAYS boring LOL! If you haven't done so, check the manual to see if the microprocessors have to be manually activated.
|
|
Wilbow
Suspended due to non-functional email address
|
27. May 2007 @ 16:17 |
Link to this message
|
|
Hi Gerry,
I'm fine and still loving the new kit, I bought a sub the other day, a GALE SUB 10, but to be honest I think its a little heavy for my house, I got used to the Mission speakers and I thought they delivered enough bass anyway, I can listen to them quite loud without them shaking the walls, but with the sub connected I can feel the vibes through the floor, and I reckon the neighbours will too! Love watching my fav Depeche Mode DVD 'DEVOTIONAL' Its like I'm there again.
Devotee
|
|
gerry1
Suspended permanently
|
27. May 2007 @ 16:42 |
Link to this message
|
|
@Wilbow...it takes a bit of a knack and experimenting to get your sub right but you really needn't annoy your neighbors to appreciate it. You should have two control knobs on your sub. Set the lowpass knob where you're not putting through the "higher notes" of the frequency response ... there should be numbers around the knob ... since your speakers are considered bookshelf and not sats, set the knob the the "lower numbers" to let only the deeper frequencies through. Experiment with the lower numbers some and just keep the other knob, the "volume" or also called the "level" knob low. You can still get a really appreciable "richness" to the bass without having to rattle the floors and walls. Actually, that's how a sub SHOULD be set. The sub should add a certain richness and fullness to the sound, NOT DOMINATE IT! A sub should be seen but not heard. You really don't have to rattle everything and annoy your neighbors to get a natural fullness and richness to the sound which will be really noticible and pleasing to the ear without disturbing anyone. Its a matter of simply setting it properly...it should be a richer and fuller sound, but not "bottom heavy"
Edit: Also, if its a bottom firing sub, either buy or make a little stand for it that takes it four inches or so off the floor. You don't want something like a thick solid piece of wood as it will defeat the purpose. Just something like a piece of 1 inch plywood cut to the size of the sub with four feet for the corners to elevate it.
Edit #2 LOL! In your receiver's "speaker setup menu", there should be three options: 1) off/on 2) LFE + Main 3) LFE
Obviously, you want it on LOL! But since you have bookshelf and not sats, try choosing just the LFE option which will put only the effects through then try LFE + Main which will put the effects in as well as the very lowest frequencies of the mains (fronts) ... see which you prefer.
This message has been edited since posting. Last time this message was edited on 27. May 2007 @ 17:08
|
|
techquest
Newbie
|
31. May 2007 @ 11:58 |
Link to this message
|
Originally posted by Wilbow:
Hi Techquest,
Thanks for taking an interest, I replaced the burnt out small caps but the amp still switched off. There are two large capacitors that I think are faulty also, there is white goo at the bottom of them that i thought was just adhesive at first, now I'm not so sure. I have found some large capacitors on ebay that are the same rating ( 63v 15000uF), but they are double the size, I dont now whether to gamble on them or just quit now and not throw good money on bad.
Cheerio for now
|
|
techquest
Newbie
|
31. May 2007 @ 12:11 |
Link to this message
|
|
Hi Wilbow
Sounds like the gue is from the caps blowing and maybe this is all due to a failure in the power supply. I assume they are radial, they stand upright, as opposed to axial which lie down for want of a better description. At 63v the must be electrolytics, they are polarised and must be the correct way round in the circuit.Do you have any numbers on the caps? They could have failed as a result of the diodes failing though.
If you had a circuit diagram reference or exact model number then maybe I can help. Not knowing your experience though I would point out the danger of working in this area 240v AC stepped down to a lower level and converted to DC volatage.
If I can help let me know.
Cheers for now.
|
|
techquest
Newbie
|
31. May 2007 @ 12:19 |
Link to this message
|
|
Hi Gerry1
Thanks for your message and yes I intend to stay around. Its always good to talk with others, no matter what their knowledge level. We can all learn something new.
Will help wherever I can on the electronics front, tube amps are one of my speacilist areas but any electronics is fine by me. As is anything IT, Telecoms and Networks, but guess they would be another forum.
Sorry for my post of Wilbows message by the way. Guess a newbie can make a simple mistake now and then.
Good talking.
Cheers for now.
|
|
Advertisement
|
|
|
|
Wilbow
Suspended due to non-functional email address
|
5. July 2007 @ 12:10 |
Link to this message
|
Hi All,
Its been a while but there have been a couple of developments over the last few days, I got nowhere with Paypal in trying to get my money back, they ruled in my favour and said I could return the item at my cost, but they couldnt guarantee recovering all my money. I treid to bargain with the tosser that I bought it from, I asked for a half refund of £30 and I would try and sell the item as faulty on Ebay to recoup as much as I could. He declined saying 'No, just return it'. There didnt seem any point returning it at a cost of around £20 if I would get less back!
Anyway, I'm sat here typing feeling a little pleased with myself, I managed to source some large capacitors from Ebay, I have just soldered them in and it works !!! WOOHOO!
Have added some pics.
http://marantz-amp.mypicgallery.com
Thanks to all who took an interest and offered advice.
Cheerio for now.
Devotee
|
