|
|
|
nero burn process failed at 8x
|
|
|
h0va
Junior Member
|
8. August 2005 @ 17:55 |
Link to this message
|
|
i thought i finally found the best thing to copy dvds (dvd shrink with nero) but my nero is screwing up when it burns... i wanted to post a log like ive seen everyone else do but it wont give me anymore than burn process failed... the burning starts out saying about 6 and a half minutes remaining...and the two places where it has buffer levels (i dont know if it is two different levels or not...) keep changing erratically... when the remaining time gets to 0:00:00 it just keeps going...then when it gets to about 60% completion the buffer levels finnally go to 100% but for only about 45 seconds then the burn fails... it has happened 3 times in a row and hasnt worked yet... im using a BRAND new computer and sony DVD-Rs so i dont know if it has anything to do with either of those two... is there some kind of driver or something i am missing or a setting i need to change? im sorta good with computers... i can normally figure my problems out but im new to the DVD burner thing..ive never had one...thanks for the help... o yea i forgot to mention...im trying to write the ifo,bup,vob files in the VIDEO_TS folder with nero... the dvd shrink rips fine...
This message has been edited since posting. Last time this message was edited on 8. August 2005 @ 18:02
|
|
Advertisement
|
|
|
|
Moderator
|
9. August 2005 @ 01:22 |
Link to this message
|
cold be just the DMA settings, however it would be better to post LAST section of Nero log to find any other settings that need looking at. it's in c:\program files\ahead\nero\nerohistory.log, but DO NOT post your serial number which usually begins with '1A21' or similar
Main PC ~ Intel C2Q Q6600 (G0 Stepping)/Gigabyte GA-EP45-DS3/2GB Crucial Ballistix PC2-8500/Zalman CNPS9700/Antec 900/Corsair HX 620W
Network ~ DD-WRT ~ 2node WDS-WPA2/AES ~ Buffalo WHR-G54S. 3node WPA2/AES ~ WRT54GS v6 (inc. WEP BSSID), WRT54G v2, WRT54G2 v1. *** Forum Rules *** |
|
h0va
Junior Member
|
9. August 2005 @ 09:16 |
Link to this message
|
Windows XP 5.1
IA32
WinAspi: -
ahead WinASPI: File 'C:\Program Files\Ahead\Nero\Wnaspi32.dll': Ver=2.0.1.59, size=160016 bytes, created 12/16/2003 10:18:06 PM
Nero version: 6.3.1.17 (Nero Express)
Recorder: <TSSTcorp CD/DVDW TS-L532A>Version: TI51 - HA 1 TA 0 - 6.3.1.17
Adapter driver: <atapi> HA 1
Drive buffer : 2048kB
Bus Type : via Inquiry data (1) -> ATAPI, detected: ATAPI
Connected to MMC as unknown drive with class-nr : 11
Drive is autodetected - recorder class: DVD+R9 DL recorder
CD-ROM: <TSSTcorp CD/DVDW TS-L532A>Version: TI51 - HA 1 TA 0 - 6.3.1.17
Adapter driver: <atapi> HA 1
=== Scsi-Device-Map ===
DiskPeripheral : FUJITSU MHU2100AT atapi Port 0 ID 0 DMA: On
CdRomPeripheral : TSSTcorp CD/DVDW TS-L532A atapi Port 1 ID 0 DMA: Off
=== CDRom-Device-Map ===
TSSTcorp CD/DVDW TS-L532 E: CDRom0
=======================
AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 83886080 (0) Byte
ShowDrvBufStat : 0
BUFE : 0
Physical memory : 1022MB (1046636kB)
Free physical memory: 552MB (565552kB)
Memory in use : 45 %
Uncached PFiles: 0x0
Use Static Write Speed Table: 0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)
8.8.2005
UDF/ISO compilation
6:49:13 PM #1 Phase 112 File dlgbrnst.cpp, Line 1845
DVD-Video files reallocation started
6:49:13 PM #2 Phase 114 File dlgbrnst.cpp, Line 1845
DVD-Video files reallocation completed (no file modified)
6:49:13 PM #3 Text 0 File Isodoc.cpp, Line 6065
Iso document burn settings
------------------------------------------
Determine maximum speed : FALSE
Simulate : FALSE
Write : TRUE
Finalize CD : TRUE
Multisession : FALSE
Burning mode : DAO
Mode : 1
ISO Level : 1 (Max. of 11 = 8 + 3 char)
Character set : ISO 9660
Joliet :FALSE
Allow pathdepth more than 8 directories : FALSE
Allow more than 255 characters in path : FALSE
Write ISO9660 ;1 file extensions : TRUE
6:49:13 PM #4 Phase 111 File dlgbrnst.cpp, Line 1845
DVD-Video files sorted
6:49:13 PM #5 Text 0 File Reader.cpp, Line 118
Reader running
6:49:13 PM #6 Text 0 File Writer.cpp, Line 124
Writer TSSTcorp CD/DVDW TS-L532A running
6:49:13 PM #7 ISO9660GEN -11 File geniso.cpp, Line 3899
First writeable address = 0 (0x00000000)
6:49:13 PM #8 ISO9660GEN -11 File geniso.cpp, Line 3899
First writeable address = 0 (0x00000000)
6:49:13 PM #9 Text 0 File Burncd.cpp, Line 3172
Turn on Disc-at-once, using DVD media
6:49:14 PM #10 Text 0 File DlgWaitCD.cpp, Line 245
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 2286111 (508:01.36, 4465MB)
6:49:14 PM #11 Text 0 File DlgWaitCD.cpp, Line 257
Write in overburning mode: NO (enabled: CD)
6:49:14 PM #12 Text 0 File DlgWaitCD.cpp, Line 2137
Recorder: TSSTcorp CD/DVDW TS-L532A, Media type: DVD-R
Disc Manufacturer: SONY08 - D1
Disc Application Code: 64, Disc Physical Code: 193
6:49:14 PM #13 Text 0 File DlgWaitCD.cpp, Line 418
>>> Protocol of DlgWaitCD activities: <<<
=========================================
6:49:14 PM #14 Text 0 File ThreadedTransferInterface.cpp, Line 813
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 (CTransferItem)
2 indices, index0 (150) not provided
original disc pos #0 + 2286112 (2286112) = #2286112/508:1.37
relocatable, disc pos for caching/writing not required/required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2286112 blocks [TSSTcorp CD/DVDW TS-L532A]
--------------------------------------------------------------
6:49:14 PM #15 Text 0 File ThreadedTransferInterface.cpp, Line 984
Prepare recorder [TSSTcorp CD/DVDW TS-L532A] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4681957376, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_RecDep_|_CtrlAdr_
0 | lead-in | 0 | 0x00 | 0x41
0 | 1 | 0 | 0x00 | 0x41
0 | 1 | 1 | 0x00 | 0x41
2286112 | lead-out | 1 | 0x00 | 0x41
6:49:14 PM #16 Phase 24 File dlgbrnst.cpp, Line 1845
Caching of files started
6:49:14 PM #17 Text 0 File Burncd.cpp, Line 4182
Cache writing successful.
6:49:14 PM #18 Phase 25 File dlgbrnst.cpp, Line 1845
Caching of files completed
6:49:14 PM #19 Phase 36 File dlgbrnst.cpp, Line 1845
Burn process started at 8x (11,080 KB/s)
6:49:14 PM #20 Text 0 File ThreadedTransferInterface.cpp, Line 2344
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0
6:49:14 PM #21 Text 0 File dlgbrnst.cpp, Line 1703
Set remaining time: 7:07,636 (427636ms) -> OK
6:49:14 PM #22 Text 0 File DVDR.cpp, Line 1876
Recording mode: Sequential Recording Mode
6:49:14 PM #23 Text 0 File Mmc.cpp, Line 20394
Set BUFE: Super Link -> ON
6:49:14 PM #24 Text 0 File DVDR.cpp, Line 2017
Start write address at LBA 0
DVD high compatibility mode: Yes
6:49:14 PM #25 Text 0 File Cdrdrv.cpp, Line 8120
---- DVD Structure: Physical Format Information (00h) ----
Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 5
Disc Size: 120 mm, Maximum Rate: 10.08 Mbps (2 h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 30000 h
End Sector Number in Layer 0: 0 h
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 0 h
Start sector number of the next Border-In: 0 h
Media Specific [16..63]:
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
7:26:07 PM #26 SCSI -1135 File Cdrdrv.cpp, Line 1442
SCSI Exec, HA 1, TA 0, LUN 0, buffer 0x0ABE0000
Status: 0x04 (0x01, SCSI_ERR)
HA-Status 0x00 (0x00, OK)
TA-Status 0x02 (0x01, SCSI_TASTATUS_CHKCOND)
Sense Key: 0x03 (KEY_MEDIUM_ERROR)
Sense Code: 0x0C
Sense Qual: 0x00
CDB Data: 0x2A 0x00 0x00 0x11 0xC6 0x60 0x00 0x00 0x20 0x00 0x00 0x00
Sense Data: 0x70 0x00 0x03 0x00 0x00 0x00 0x00 0x0A
0x00 0x00 0x00 0x00 0x0C 0x00
7:26:07 PM #27 CDR -1135 File Writer.cpp, Line 304
Write error
7:26:07 PM #28 Text 0 File ThreadedTransfer.cpp, Line 229
all writers idle, stopping conversion
7:26:07 PM #29 Text 0 File ThreadedTransfer.cpp, Line 223
conversion idle, stopping reader
7:26:08 PM #30 Text 0 File DVDR.cpp, Line 2253
EndDAO: Last written address was 1164895
7:26:08 PM #31 Text 0 File dlgbrnst.cpp, Line 1703
Set remaining time: 0:00,000 (0ms) -> OK
7:26:08 PM #32 Text 0 File dlgbrnst.cpp, Line 1703
Set remaining time: 0:00,000 (0ms) -> OK
7:26:08 PM #33 Phase 38 File dlgbrnst.cpp, Line 1845
Burn process failed at 8x (11,080 KB/s)
|
Moderator
|
9. August 2005 @ 09:25 |
Link to this message
|
Quote:
Nero version: 6.3.1.17 (Nero Express)
- way old, latest is 6.6.0.16
Quote:
Recorder: <TSSTcorp CD/DVDW TS-L532A>Version: TI51
- not yet sure if this firmware is out of date or not
Quote:
Connected to MMC as unknown drive with class-nr : 11
Drive is autodetected - recorder class: DVD+R9 DL recorder
- yup, Nero is too old to recognise your burner correctly
Quote:
DiskPeripheral : FUJITSU MHU2100AT atapi Port 0 ID 0 DMA: On
CdRomPeripheral : TSSTcorp CD/DVDW TS-L532A atapi Port 1 ID 0 DMA: Off
- get DMA back ON via this - http://home.comcast.net/~bbmayo/FAQ.htm
Quote:
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 2286111 (508:01.36, 4465MB)
- you burning too close to outer edge of discs. If you use DVD Shrink, set target size to 4300MB in Shrink's preferences thus avoiding outer edge and not sacrificing much space
Quote:
Write error
- splat!
Quote:
Burn process failed at 8x (11,080 KB/s)
- try 4x
you're missing the last few lines of logfile, but this is a good start
Main PC ~ Intel C2Q Q6600 (G0 Stepping)/Gigabyte GA-EP45-DS3/2GB Crucial Ballistix PC2-8500/Zalman CNPS9700/Antec 900/Corsair HX 620W
Network ~ DD-WRT ~ 2node WDS-WPA2/AES ~ Buffalo WHR-G54S. 3node WPA2/AES ~ WRT54GS v6 (inc. WEP BSSID), WRT54G v2, WRT54G2 v1. *** Forum Rules ***
|
|
h0va
Junior Member
|
9. August 2005 @ 10:17 |
Link to this message
|
Existing drivers:
File 'Drivers\ADPU160M.SYS': Ver=v3.60a (Lab01_N(johnstra).010529-2218), size=101888 bytes, created 8/18/2001 12:07:32 AM
File 'Drivers\atapi.sys': Ver=5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), size=95360 bytes, created 8/4/2004 8:59:44 AM (Adapter driver for rec)
Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
theres the last lines... sorry... i did the dma stuff and the target size to 4300... but the Nero came installed on my computer when i bought it and im not sure how to update it with not having the cd/serial number and everything... any ideas without having to pay for it? and how would i figure out wat to do with the firmware?
|
Moderator
|
9. August 2005 @ 11:01 |
Link to this message
|
|
The last few lines of log look fine. That's a good question about the serial number. What I mean is you shouldn't need to worry about entering the serial number just to update. When I've uninstalled nero before, Nero has printed the serial number on screen and prompts you to write it down just in case. However I'm not near a pc at the moment to check how you verify your own serial number. I'm on a handheld which is a bit crap for using on the internet. Follow the other suggestions for now, leaving nero alone, and as I say the firmware might be fine. What you can do after fixing the other stuff is to do a 'simulation' burn which asks for a blank disk and just goes thru the motions of burning, thus testing out your fixes. See how you go with that for now..
Main PC ~ Intel C2Q Q6600 (G0 Stepping)/Gigabyte GA-EP45-DS3/2GB Crucial Ballistix PC2-8500/Zalman CNPS9700/Antec 900/Corsair HX 620W
Network ~ DD-WRT ~ 2node WDS-WPA2/AES ~ Buffalo WHR-G54S. 3node WPA2/AES ~ WRT54GS v6 (inc. WEP BSSID), WRT54G v2, WRT54G2 v1. *** Forum Rules ***
This message has been edited since posting. Last time this message was edited on 9. August 2005 @ 12:46
|
|
h0va
Junior Member
|
9. August 2005 @ 13:04 |
Link to this message
|
|
i did a simulation burn already...sitting at fudruckers... lol at 4x and it said it completed successfully... so im going to try to burn it for real now and ill let you know how it goes...
|
Moderator
|
9. August 2005 @ 13:08 |
Link to this message
|
|
nice one...
Main PC ~ Intel C2Q Q6600 (G0 Stepping)/Gigabyte GA-EP45-DS3/2GB Crucial Ballistix PC2-8500/Zalman CNPS9700/Antec 900/Corsair HX 620W
Network ~ DD-WRT ~ 2node WDS-WPA2/AES ~ Buffalo WHR-G54S. 3node WPA2/AES ~ WRT54GS v6 (inc. WEP BSSID), WRT54G v2, WRT54G2 v1. *** Forum Rules ***
|
|
h0va
Junior Member
|
9. August 2005 @ 17:49 |
Link to this message
|
it burned right... then i tried it directly burning through DVD Shrink instead of putting the files on and everything and it worked fine... and its gotten faster with each movie... which i hope will keep up... im going to hold off on downloading a new Nero since everything is working now how it is... when i had icopydvds2 there was intervideo(not sure if thats the name) player that was automatically installed when u put in some movies and messed up the program... is there anything like that player thing that will mess up DVD Shrink? because i know it was from blade trinity and im hesitant to copy it now so it wont mess everything up... thanks for ur help again!
|
|
Advertisement
|
|
|
Moderator
|
10. August 2005 @ 02:12 |
Link to this message
|
|
no worries. i think the player that sometimes get installed is called Interactual - uninstall it
Main PC ~ Intel C2Q Q6600 (G0 Stepping)/Gigabyte GA-EP45-DS3/2GB Crucial Ballistix PC2-8500/Zalman CNPS9700/Antec 900/Corsair HX 620W
Network ~ DD-WRT ~ 2node WDS-WPA2/AES ~ Buffalo WHR-G54S. 3node WPA2/AES ~ WRT54GS v6 (inc. WEP BSSID), WRT54G v2, WRT54G2 v1. *** Forum Rules ***
|
|
