|
|
|
Just installed nero 6.6.0.15a, now i get Exception OE errors and the end of simple burning!!??
|
|
|
givafuc
Newbie
|
13. August 2005 @ 22:53 |
Link to this message
|
|
Back story: I have WinME, had Nero 5.something which burned fine with this current burner, same CD-R's as other successfull compilations. That's all I can think of right now, but will certainly supply more important info I've sure of forgotten to add. Anyway, I'm fairly experienced with converting video files to anything I need so that is why I upgraded when I felt I needed to.
The PROBLEM is this: Exception OE at 0028:C003C23E in VxD IOS(01)+000019BE. This was called from 0028:C1C2A300 in VxD Voltrack(04)+00000430. And of course that damn blue screen made me restart the cpu. This has only done this since that install of 6.6 from the old working 5.something. The solution is simple I'm sure, usually is, but this must have some conflict with some previous install of something else. I have Adaptec DirectCD installed, but that has been there for years. It might conflict with this install rather than the old one, I don't know. I also tried to do successfull searching for a solution using Google and finally this forum using the some keywords from above problem and the word Nero. Nothing really matched my specific problem. That is why I think it is something really simple, since not many people have this problem. Anyway, I can try to give read-outs of any logs anyone asks of me, tell me how, never had to before this.
This my system summary courtesy of SiSystem Sandra:SiSoftware Sandra
System
Host Name : OEMCOMPUTER
User : default
Domain : OEMWORKGROUP
Processor
Model : Intel(R) Celeron(TM) CPU 1200MHz
Speed : 1.20GHz
Performance Rating : PR1435 (estimated)
Type : Standard
L2 On-board Cache : 256kB ECC Synchronous ATC (8-way, 32 byte line size)
Mainboard
Bus(es) : X-Bus PCI USB
MP Support : 1 CPU(s)
MP APIC : No
System BIOS : Compaq 686P9 v1.03
System : Compaq
Mainboard : Compaq 07A8h
Total Memory : 510MB SDRAM
Chipset 1
Model : Intel Corporation 82815/G/EG/P/EP Solano Host-Hub Interface Bridge (GMCH/MCH B0-step)
Front Side Bus Speed : 1x 100MHz (100MHz data rate)
Total Memory : 512MB SDRAM
Shared Memory : 1MB
Memory Bus Speed : 1x 100MHz (100MHz data rate)
Video System
Monitor/Panel : Default Monitor
Adapter : Intel(R) 82815 Graphics Controller
Imaging Device : hp officejet v series
Physical Storage Devices
Hard Disk : GENERIC IDE DISK TYPE01
Hard Disk : GENERIC NEC FLOPPY DISK
CD-ROM/DVD : SAMSUNG CD-ROM SC-148
CD-ROM/DVD : SAMSUNG CD-R/RW SW-208B
Logical Storage Devices
1.44MB 3.5" (A:) : N/A
Local disk (C:) : 28.6GB (1.2GB, 4% Free) (FAT32)
CD-ROM/DVD (D:) : N/A
CD-ROM/DVD (E:) : N/A
Peripherals
Serial/Parallel Port(s) : 3 COM / 1 LPT
USB Controller/Hub : Intel(r) 82801BA/BAM USB Universal Host Controller 1
USB Controller/Hub : Intel(r) 82801BA/BAM USB Universal Host Controller 2
USB Controller/Hub : USB Root Hub
USB Controller/Hub : USB Root Hub
Keyboard : Standard 101/102-Key or Microsoft Natural Keyboard
Mouse : Logitech-compatible Mouse (PS/2)
MultiMedia Device(s)
Device : AC'97 Driver for Intel(r) 82801BA/BAM Controller
Device : Microsoft Kernel System Audio Renderer
Device : Microsoft Kernel DRM Descrambler Filter
Device : Microsoft Kernel GS Wavetable Synthesizer
Device : Microsoft Kernel Audio Mixer
Device : Microsoft Kernel Audio Splitter
Device : Microsoft Kernel DLS Synthesizer
Communication Device(s)
Device : Conexant SoftK56 PCI Modem(M) #3
Printers and Faxes
Model : HP Printer Scanner Copier 300
Model : Acrobat Distiller
Model : Generic PostScript Printer
Model : hp officejet v series fax
Model : hp officejet v series
Model : Visioneer Color
Model : Visioneer
Model : HP DeskJet 720C v10.3
Power Management
AC Line Status : On-Line
Operating System(s)
Windows System : Microsoft Windows Me (Win32 x86) 4.90.3000 ( )
DOS System : Microsoft MS-DOS Version 8.00 A
Network Services
Adapter : Dial-Up Adapter
Adapter : Realtek RTL8139(A) PCI Fast Ethernet Adapter
I know it's pitiful, but I've saved close to a thousand dollars with this machine, hence right now as you might notice my hard drive space, that is because.... nevermind that.
After reading numerous threads from this site, I'm convinced you people really know your way around. Any help would be greatly appreciated.
PS:I don't think I explained what I was doing in the first place when this happened. I was going to burn some .OGM files to a CD, of course, then convert that to VCD on another CPU, which is actually slower than this one if you want a good laugh. It was the first time I tried to burn with this new install/upgrade. Anyway, that's that.
|
|
Advertisement
|
 |
|
|
Moderator
|
14. August 2005 @ 05:18 |
Link to this message
|
try uninstalling Nero, then completely zapping it with Nero's Clean Tools here - Nero.com/en/Clean_Tools.html" class="korostus" target="_blank">http://www.Nero.com/en/Clean_Tools.html
do you still use packet writing software, if you don't need it anyway, get rid
Main PC ~ Intel C2Q Q6600 (G0 Stepping)/Gigabyte GA-EP45-DS3/2GB Crucial Ballistix PC2-8500/Zalman CNPS9700/Antec 900/Corsair HX 620W
Network ~ DD-WRT ~ 2node WDS-WPA2/AES ~ Buffalo WHR-G54S. 3node WPA2/AES ~ WRT54GS v6 (inc. WEP BSSID), WRT54G v2, WRT54G2 v1. *** Forum Rules *** |
|
givafuc
Newbie
|
14. August 2005 @ 07:16 |
Link to this message
|
|
What do you mean "packet writing software?" Hell I'll get rid of it ASAP. I downloaded all of the clean tools, will post results.
|
Moderator
|
14. August 2005 @ 08:28 |
Link to this message
|
DirectCD, or InCD by Nero, and Roxio also has p/writing software too..
Main PC ~ Intel C2Q Q6600 (G0 Stepping)/Gigabyte GA-EP45-DS3/2GB Crucial Ballistix PC2-8500/Zalman CNPS9700/Antec 900/Corsair HX 620W
Network ~ DD-WRT ~ 2node WDS-WPA2/AES ~ Buffalo WHR-G54S. 3node WPA2/AES ~ WRT54GS v6 (inc. WEP BSSID), WRT54G v2, WRT54G2 v1. *** Forum Rules ***
|
|
givafuc
Newbie
|
14. August 2005 @ 11:50 |
Link to this message
|
|
Well at least I'm not getting that damn blue screen crap. Instead its just a burn failure. Here's the log:
Michael *********
Fuck Shit Up
1A23-0*******************
Windows 98 4.90 (ME)
IA32
WinAspi: File 'Wnaspi32.dll': Ver=1, 0, 0, 0, size=36864 bytes, created 6/8/2000 5:00:00 PM
ahead WinASPI: File 'C:\PROGRAM FILES\AHEAD\NERO\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 10/26/2004 6:35:34 PM
Nero Version: 6.6.0.15
Internal Version: 6, 6, 0, 15h
Recorder: <SAMSUNG CD-R/RW SW-208B> Version: BT02 - HA 0 TA 1 - 6.6.0.15
Adapter driver: <ESDI_506> HA 0
Drive buffer : 4096kB
Bus Type : default (0) -> ATAPI, detected: ATAPI
CD-ROM: <SAMSUNG CD-ROM SC-148 >Version: ST01 - HA 0 TA 0 - 6.6.0.15
Adapter driver: <ESDI_506> HA 0
SAMSUNG CD-ROM SC-148 (Target 0, D:): Autoinsert Off, DMA On, Disconnect ?, SyncDataXfer ?
SAMSUNG CD-R/RW SW-208B (Target 1, E:): Autoinsert Off, DMA On, Disconnect ?, SyncDataXfer ?
Excluded drive IDs:
WriteBufferSize: 74448896 (0) Byte
ShowDrvBufStat : 0
BUFE : 0
Physical memory : 510MB (522636kB)
Free physical memory: 243MB (249224kB)
Memory in use : 44 %
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)
14.8.2005
CD-ROM (ISO)
3:45:04 PM #1 Text 0 File Isodoc.cpp, Line 6314
Iso document burn settings
------------------------------------------
Determine maximum speed : FALSE
Simulate : TRUE
Write : FALSE
Finalize CD : FALSE
Multisession : TRUE
Multisession type: : Start multisession
Burning mode : TAO
Mode : 1
ISO Level : 1 (Max. of 11 = 8 + 3 char)
Character set : ISO 9660
Joliet : TRUE
Allow pathdepth more than 8 directories : TRUE
Allow more than 255 characters in path : TRUE
Write ISO9660 ;1 file extensions : TRUE
3:45:05 PM #2 Text 0 File Reader.cpp, Line 127
Reader running
3:45:05 PM #3 Text 0 File Writer.cpp, Line 122
Writer SAMSUNG CD-R/RW SW-208B running
3:45:05 PM #4 ISO9660GEN -11 File geniso.cpp, Line 3309
First writeable address = 0 (0x00000000)
3:45:05 PM #5 Text 0 File Burncd.cpp, Line 3231
Turn on Track-At-Once, using CD-R/RW media
3:45:05 PM #6 Text 0 File DlgWaitCD.cpp, Line 269
Last possible write address on media: 359845 ( 79:59.70)
Last address to be written: 599 ( 0:09.74)
3:45:05 PM #7 Text 0 File DlgWaitCD.cpp, Line 281
Write in overburning mode: NO (enabled: CD)
3:45:05 PM #8 Text 0 File DlgWaitCD.cpp, Line 2477
Recorder: SAMSUNG CD-R/RW SW-208B;
CDR code: 00 97 26 66; OSJ entry from: CMC Magnetics Corporation
ATIP Data: ?
3:45:05 PM #9 Text 0 File DlgWaitCD.cpp, Line 447
>>> Protocol of DlgWaitCD activities: <<<
=========================================
3:45:05 PM #10 Text 0 File ThreadedTransferInterface.cpp, Line 830
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
2 indices, index0 (150) not provided
original disc pos #0 + 600 (600) = #600/0:8.0
relocatable, disc pos for caching/writing not required/ required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 598 blocks [SAMSUNG CD-R/RW SW-208B]
--------------------------------------------------------------
3:45:05 PM #11 Text 0 File ThreadedTransferInterface.cpp, Line 1043
Prepare recorder [SAMSUNG CD-R/RW SW-208B] for write in TAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc not fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 307200 1536000, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________
-150 | lead-in | 0 | 0x41 | 0x00
-150 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
600 | lead-out | 1 | 0x41 | 0x00
3:45:05 PM #12 Text 0 File ThreadedTransferInterface.cpp, Line 1111
Removed 2 run-out blocks from end of track 1. Length: 600 -> 598.
3:45:05 PM #13 Phase 24 File dlgbrnst.cpp, Line 1832
Caching of files started
3:45:05 PM #14 Text 0 File Burncd.cpp, Line 4116
Cache writing successful.
3:45:05 PM #15 Phase 25 File dlgbrnst.cpp, Line 1832
Caching of files completed
3:45:05 PM #16 Phase 32 File dlgbrnst.cpp, Line 1832
Simulation started at 8x (1,200 KB/s)
3:45:10 PM #17 Text 0 File ThreadedTransferInterface.cpp, Line 2643
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0
3:45:13 PM #18 SCSI -1064 File Cdrdrv.cpp, Line 1436
SCSI Exec, HA 0, TA 1, LUN 0, buffer 0x02C80000
Status: 0x04 (0x01, SCSI_ERR)
HA-Status 0x00 (0x00, OK)
TA-Status 0x02 (0x01, SCSI_TASTATUS_CHKCOND)
Sense Key: 0x05 (KEY_ILLEGAL_REQUEST)
Sense Code: 0x21
Sense Qual: 0x00
CDB Data: 0x2A 0x00 0x00 0x00 0x00 0x20 0x00 0x00 0x20 0x00 0x00 0x00
Sense Data: 0x70 0x00 0x05 0x00 0x00 0x00 0x00 0x0A
0x00 0x00 0x00 0x00 0x21 0x00
3:45:13 PM #19 CDR -1064 File Writer.cpp, Line 311
Invalid block address
3:45:13 PM #20 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion
3:45:13 PM #21 CDR -201 File WriterStatus.cpp, Line 157
Invalid write state
SAMSUNG CD-R/RW SW-208B\H0 T1
3:45:13 PM #22 TRANSFER -18 File WriterStatus.cpp, Line 157
Could not perform EndTrack
3:45:13 PM #23 Phase 34 File dlgbrnst.cpp, Line 1832
Simulation failed at 8x (1,200 KB/s)
Existing drivers:
File 'IoSubSys\SCSI1HLP.VXD': Ver=4.90.3000, size=19278 bytes, created 6/8/2000 5:00:00 PM
File 'IoSubsys\NEROCD95.VXD': Ver=4.5.0.14, size=39882 bytes, created 3/11/2002 11:55:38 AM
File 'IoSubsys\CDR4VSD.VXD': Ver=5.3.2.31, size=101616 bytes, created 3/1/2003 8:08:58 PM
File 'IoSubsys\CDRALVSD.VXD': Ver=5.3.2.31, size=20043 bytes, created 3/1/2003 8:08:58 PM
File 'IoSubsys\CDFS.VXD': Ver=4.90.3000, size=59141 bytes, created 6/8/2000 5:00:00 PM
File 'IoSubsys\ESDI_506.PDR': Ver=4.90.3000, size=25365 bytes, created 6/8/2000 5:00:00 PM
File 'IoSubsys\USBMPHLP.PDR': Ver=4.90.3000, size=4861 bytes, created 6/8/2000 5:00:00 PM
File '..\System32\Drivers\1394bus.sys': Ver=4.90.3000.1, size=44240 bytes, created 6/8/2000 5:00:00 PM
File '..\System32\Drivers\Ohci1394.sys': Ver=4.90.3000.1, size=49488 bytes, created 6/8/2000 5:00:00 PM
File '..\System32\Drivers\Sbp2port.sys': Ver=4.90.3000.1, size=36336 bytes, created 6/8/2000 5:00:00 PM
File 'IoSubsys\Disktsd.vxd': Ver=4.90.3000, size=18663 bytes, created 6/8/2000 5:00:00 PM
Registry Keys:
It is probably a shit situation, but it's never been a problem up until this upgrade. Anyway, thank you Creaky so far for the help.
Do changes I will, Yoda might say, that green bastard.
|
Moderator
|
14. August 2005 @ 11:57 |
Link to this message
|
here ya go Yoda :)
Quote:
Recorder: <SAMSUNG CD-R/RW SW-208B> Version: BT02
- firmware's out of date, version BT04 is here - http://forum.rpc1.org/dl_firmware.php?download_id=653
Quote:
Existing drivers:
File 'IoSubsys\CDR4VSD.VXD': Ver=5.3.2.31, size=101616 bytes, created 3/1/2003 8:08:58 PM
File 'IoSubsys\CDRALVSD.VXD': Ver=5.3.2.31, size=20043 bytes, created 3/1/2003 8:08:58 PM
- is that Roxio there, maybe uninstall it and see if you get better success
Main PC ~ Intel C2Q Q6600 (G0 Stepping)/Gigabyte GA-EP45-DS3/2GB Crucial Ballistix PC2-8500/Zalman CNPS9700/Antec 900/Corsair HX 620W
Network ~ DD-WRT ~ 2node WDS-WPA2/AES ~ Buffalo WHR-G54S. 3node WPA2/AES ~ WRT54GS v6 (inc. WEP BSSID), WRT54G v2, WRT54G2 v1. *** Forum Rules ***
|
|
givafuc
Newbie
|
14. August 2005 @ 15:25 |
Link to this message
|
|
The install text file is encrypted.WTF!! I looked everywhere for something that might help but nothing come about. But what I did find out was that I didn't need to be doing anything without reading the install directions because "Read carefully the installation notes of your firmware before you upgrade. The Firmware Page and the drive manufacturer can't be responsable on REMEMBER: This is at your own risk!!!!" But the damn thing is unreadable. I'm sure there is a simple solution, just like most of everything. Thanks.
|
|
givafuc
Newbie
|
14. August 2005 @ 17:53 |
Link to this message
|
|
Well the hell with that screwed file, I'll kept searching and found this:Samsung is not responsable for problems during the firmware upgrade. When you encounter problems during the upgrade, please contact a Samsung Service Center.
If your drive is still in warranty please contact your retailer first.
The firmware BS04 of SW-208B
How to upgrade in Windows.
1. Download the zip to your computer.
2. Unzip the zip file, you can find the "SFDNWIN.EXE" and "BS04.BIN"
3. Run the SFDNWIN.EXE(windows 95/98,ME or sfdnw2k(win2000) file on windows.
4. When there"s pop-up menu, you choose SYSTEM.
Press the OPEN, and take the file what you want to down.
5.If you press the FLASH, Download is started.
6. When the FIRMWARE DOWNLOAD is completed, power the PC off.
Boot up the PC again.
It wasn't talking about BT04 but BS04, it had the same files along with it though. I figure if that process works for that, than it must work for this, considering it deals mostly with the same animal. I followed the instructions and simulated a burn and succeded. This is the Log from the successfull simulation/burn:
Michael ******
Fuck Shit Up
1A23-*******************
Windows 98 4.90 (ME)
IA32
WinAspi: File 'Wnaspi32.dll': Ver=1, 0, 0, 0, size=36864 bytes, created 6/8/2000 5:00:00 PM
ahead WinASPI: File 'C:\PROGRAM FILES\AHEAD\NERO\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 10/26/2004 6:35:34 PM
Nero Version: 6.6.0.15
Internal Version: 6, 6, 0, 15h
Recorder: <SAMSUNG CD-R/RW SW-208B> Version: BT02 - HA 0 TA 1 - 6.6.0.15
Adapter driver: <ESDI_506> HA 0
Drive buffer : 4096kB
Bus Type : default (0) -> ATAPI, detected: ATAPI
CD-ROM: <SAMSUNG CD-ROM SC-148 >Version: ST01 - HA 0 TA 0 - 6.6.0.15
Adapter driver: <ESDI_506> HA 0
SAMSUNG CD-ROM SC-148 (Target 0, D:): Autoinsert Off, DMA On, Disconnect ?, SyncDataXfer ?
SAMSUNG CD-R/RW SW-208B (Target 1, E:): Autoinsert Off, DMA On, Disconnect ?, SyncDataXfer ?
Excluded drive IDs:
WriteBufferSize: 74448896 (0) Byte
ShowDrvBufStat : 0
BUFE : 0
Physical memory : 510MB (522636kB)
Free physical memory: 243MB (249480kB)
Memory in use : 43 %
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)
14.8.2005
CD-ROM (ISO)
9:40:03 PM #1 Text 0 File Isodoc.cpp, Line 6314
Iso document burn settings
------------------------------------------
Determine maximum speed : FALSE
Simulate : TRUE
Write : FALSE
Finalize CD : FALSE
Multisession : TRUE
Multisession type: : Start multisession
Burning mode : TAO
Mode : 1
ISO Level : 1 (Max. of 11 = 8 + 3 char)
Character set : ISO 9660
Joliet : TRUE
Allow pathdepth more than 8 directories : TRUE
Allow more than 255 characters in path : TRUE
Write ISO9660 ;1 file extensions : TRUE
9:40:03 PM #2 Text 0 File Reader.cpp, Line 127
Reader running
9:40:03 PM #3 Text 0 File Writer.cpp, Line 122
Writer SAMSUNG CD-R/RW SW-208B running
9:40:03 PM #4 ISO9660GEN -11 File geniso.cpp, Line 3309
First writeable address = 0 (0x00000000)
9:40:03 PM #5 Text 0 File Burncd.cpp, Line 3231
Turn on Track-At-Once, using CD-R/RW media
9:40:04 PM #6 Text 0 File DlgWaitCD.cpp, Line 269
Last possible write address on media: 359845 ( 79:59.70)
Last address to be written: 599 ( 0:09.74)
9:40:04 PM #7 Text 0 File DlgWaitCD.cpp, Line 281
Write in overburning mode: NO (enabled: CD)
9:40:04 PM #8 Text 0 File DlgWaitCD.cpp, Line 2477
Recorder: SAMSUNG CD-R/RW SW-208B;
CDR code: 00 97 26 66; OSJ entry from: CMC Magnetics Corporation
ATIP Data: ?
9:40:04 PM #9 Text 0 File DlgWaitCD.cpp, Line 447
>>> Protocol of DlgWaitCD activities: <<<
=========================================
9:40:04 PM #10 Text 0 File ThreadedTransferInterface.cpp, Line 830
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
2 indices, index0 (150) not provided
original disc pos #0 + 600 (600) = #600/0:8.0
relocatable, disc pos for caching/writing not required/ required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 598 blocks [SAMSUNG CD-R/RW SW-208B]
--------------------------------------------------------------
9:40:04 PM #11 Text 0 File ThreadedTransferInterface.cpp, Line 1043
Prepare recorder [SAMSUNG CD-R/RW SW-208B] for write in TAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc not fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 307200 1536000, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________
-150 | lead-in | 0 | 0x41 | 0x00
-150 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
600 | lead-out | 1 | 0x41 | 0x00
9:40:04 PM #12 Text 0 File ThreadedTransferInterface.cpp, Line 1111
Removed 2 run-out blocks from end of track 1. Length: 600 -> 598.
9:40:04 PM #13 Phase 24 File dlgbrnst.cpp, Line 1832
Caching of files started
9:40:04 PM #14 Text 0 File Burncd.cpp, Line 4116
Cache writing successful.
9:40:04 PM #15 Phase 25 File dlgbrnst.cpp, Line 1832
Caching of files completed
9:40:04 PM #16 Phase 32 File dlgbrnst.cpp, Line 1832
Simulation started at 8x (1,200 KB/s)
9:40:04 PM #17 Text 0 File ThreadedTransferInterface.cpp, Line 2643
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0
9:40:05 PM #18 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion
9:40:15 PM #19 Phase 33 File dlgbrnst.cpp, Line 1832
Simulation completed successfully at 8x (1,200 KB/s)
Existing drivers:
File 'IoSubSys\SCSI1HLP.VXD': Ver=4.90.3000, size=19278 bytes, created 6/8/2000 5:00:00 PM
File 'IoSubsys\NEROCD95.VXD': Ver=4.5.0.14, size=39882 bytes, created 3/11/2002 11:55:38 AM
File 'IoSubsys\CDR4VSD.VXD': Ver=5.3.2.31, size=101616 bytes, created 3/1/2003 8:08:58 PM
File 'IoSubsys\CDRALVSD.VXD': Ver=5.3.2.31, size=20043 bytes, created 3/1/2003 8:08:58 PM
File 'IoSubsys\CDFS.VXD': Ver=4.90.3000, size=59141 bytes, created 6/8/2000 5:00:00 PM
File 'IoSubsys\ESDI_506.PDR': Ver=4.90.3000, size=25365 bytes, created 6/8/2000 5:00:00 PM
File 'IoSubsys\USBMPHLP.PDR': Ver=4.90.3000, size=4861 bytes, created 6/8/2000 5:00:00 PM
File '..\System32\Drivers\1394bus.sys': Ver=4.90.3000.1, size=44240 bytes, created 6/8/2000 5:00:00 PM
File '..\System32\Drivers\Ohci1394.sys': Ver=4.90.3000.1, size=49488 bytes, created 6/8/2000 5:00:00 PM
File '..\System32\Drivers\Sbp2port.sys': Ver=4.90.3000.1, size=36336 bytes, created 6/8/2000 5:00:00 PM
File 'IoSubsys\Disktsd.vxd': Ver=4.90.3000, size=18663 bytes, created 6/8/2000 5:00:00 PM
Registry Keys:
Hopefully this is the end of this dilemma(MS). Thank you Creaky. You've earned my respect and now I can go on to pir.... oh nevermind that. LOL.
|
|
givafuc
Newbie
|
14. August 2005 @ 18:30 |
Link to this message
|
|
Now why in the Hell would it fail on me saying of disk reached on a 681MB job? Here is the damn log: again:
Windows 98 4.90 (ME)
IA32
WinAspi: File 'Wnaspi32.dll': Ver=1, 0, 0, 0, size=36864 bytes, created 6/8/2000 5:00:00 PM
ahead WinASPI: File 'C:\PROGRAM FILES\AHEAD\NERO\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 10/26/2004 6:35:34 PM
Nero Version: 6.6.0.15
Internal Version: 6, 6, 0, 15h
Recorder: <SAMSUNG CD-R/RW SW-208B> Version: BT02 - HA 0 TA 1 - 6.6.0.15
Adapter driver: <ESDI_506> HA 0
Drive buffer : 4096kB
Bus Type : default (0) -> ATAPI, detected: ATAPI
CD-ROM: <SAMSUNG CD-ROM SC-148 >Version: ST01 - HA 0 TA 0 - 6.6.0.15
Adapter driver: <ESDI_506> HA 0
SAMSUNG CD-ROM SC-148 (Target 0, D:): Autoinsert Off, DMA On, Disconnect ?, SyncDataXfer ?
SAMSUNG CD-R/RW SW-208B (Target 1, E:): Autoinsert Off, DMA On, Disconnect ?, SyncDataXfer ?
Excluded drive IDs:
WriteBufferSize: 74448896 (0) Byte
ShowDrvBufStat : 0
BUFE : 0
Physical memory : 510MB (522636kB)
Free physical memory: 0MB (412kB)
Memory in use : 62 %
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)
14.8.2005
CD-ROM (ISO)
10:14:13 PM #1 Text 0 File Isodoc.cpp, Line 6314
Iso document burn settings
------------------------------------------
Determine maximum speed : FALSE
Simulate : FALSE
Write : TRUE
Finalize CD : FALSE
Multisession : TRUE
Multisession type: : Start multisession
Burning mode : TAO
Mode : 1
ISO Level : 1 (Max. of 11 = 8 + 3 char)
Character set : ISO 9660
Joliet : TRUE
Allow pathdepth more than 8 directories : TRUE
Allow more than 255 characters in path : TRUE
Write ISO9660 ;1 file extensions : TRUE
10:14:13 PM #2 Text 0 File Reader.cpp, Line 127
Reader running
10:14:13 PM #3 Text 0 File Writer.cpp, Line 122
Writer SAMSUNG CD-R/RW SW-208B running
10:14:13 PM #4 ISO9660GEN -11 File geniso.cpp, Line 3309
First writeable address = 0 (0x00000000)
10:14:13 PM #5 Text 0 File Burncd.cpp, Line 3231
Turn on Track-At-Once, using CD-R/RW media
10:14:13 PM #6 Text 0 File DlgWaitCD.cpp, Line 269
Last possible write address on media: 359845 ( 79:59.70)
Last address to be written: 348352 ( 77:26.52)
10:14:13 PM #7 Text 0 File DlgWaitCD.cpp, Line 281
Write in overburning mode: NO (enabled: CD)
10:14:13 PM #8 Text 0 File DlgWaitCD.cpp, Line 2477
Recorder: SAMSUNG CD-R/RW SW-208B;
CDR code: 00 97 26 66; OSJ entry from: CMC Magnetics Corporation
ATIP Data: ?
10:14:13 PM #9 Text 0 File DlgWaitCD.cpp, Line 447
>>> Protocol of DlgWaitCD activities: <<<
=========================================
10:14:13 PM #10 Text 0 File ThreadedTransferInterface.cpp, Line 830
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
2 indices, index0 (150) not provided
original disc pos #0 + 348353 (348353) = #348353/77:24.53
relocatable, disc pos for caching/writing not required/ required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 348351 blocks [SAMSUNG CD-R/RW SW-208B]
--------------------------------------------------------------
10:14:13 PM #11 Text 0 File ThreadedTransferInterface.cpp, Line 1043
Prepare recorder [SAMSUNG CD-R/RW SW-208B] for write in TAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc not fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 307200 713734144, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________
-150 | lead-in | 0 | 0x41 | 0x00
-150 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
348353 | lead-out | 1 | 0x41 | 0x00
10:14:13 PM #12 Text 0 File ThreadedTransferInterface.cpp, Line 1111
Removed 2 run-out blocks from end of track 1. Length: 348353 -> 348351.
10:14:13 PM #13 Phase 24 File dlgbrnst.cpp, Line 1832
Caching of files started
10:14:13 PM #14 Text 0 File Burncd.cpp, Line 4116
Cache writing successful.
10:14:13 PM #15 Phase 25 File dlgbrnst.cpp, Line 1832
Caching of files completed
10:14:13 PM #16 Phase 36 File dlgbrnst.cpp, Line 1832
Burn process started at 8x (1,200 KB/s)
10:14:14 PM #17 Text 0 File ThreadedTransferInterface.cpp, Line 2643
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0
10:24:00 PM #18 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion
10:24:05 PM #19 Text 0 File Mmc.cpp, Line 16311
<SAMSUNG CD-R/RW SW-208B > start Close Session
10:24:05 PM #20 SCSI -1036 File Cdrdrv.cpp, Line 1182
SCSI Exec, HA 0, TA 1, LUN 0
Status: 0x04 (0x01, SCSI_ERR)
HA-Status 0x00 (0x00, OK)
TA-Status 0x02 (0x01, SCSI_TASTATUS_CHKCOND)
Sense Key: 0x06 (KEY_UNIT_ATTENTION)
Sense Code: 0x3B
Sense Qual: 0x0F
CDB Data: 0x5B 0x01 0x02 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
Sense Data: 0x70 0x00 0x06 0x00 0x00 0x00 0x00 0x0A
0x00 0x00 0x00 0x00 0x3B 0x0F
10:24:05 PM #21 CDR -1036 File ThreadedTransferInterface.cpp, Line 1286
End of disc reached
10:24:05 PM #22 TRANSFER -19 File ThreadedTransferInterface.cpp, Line 1286
Could not perform Fixation
10:24:05 PM #23 Phase 38 File dlgbrnst.cpp, Line 1832
Burn process failed at 8x (1,200 KB/s)
Existing drivers:
File 'IoSubSys\SCSI1HLP.VXD': Ver=4.90.3000, size=19278 bytes, created 6/8/2000 5:00:00 PM
File 'IoSubsys\NEROCD95.VXD': Ver=4.5.0.14, size=39882 bytes, created 3/11/2002 11:55:38 AM
File 'IoSubsys\CDR4VSD.VXD': Ver=5.3.2.31, size=101616 bytes, created 3/1/2003 8:08:58 PM
File 'IoSubsys\CDRALVSD.VXD': Ver=5.3.2.31, size=20043 bytes, created 3/1/2003 8:08:58 PM
File 'IoSubsys\CDFS.VXD': Ver=4.90.3000, size=59141 bytes, created 6/8/2000 5:00:00 PM
File 'IoSubsys\ESDI_506.PDR': Ver=4.90.3000, size=25365 bytes, created 6/8/2000 5:00:00 PM
File 'IoSubsys\USBMPHLP.PDR': Ver=4.90.3000, size=4861 bytes, created 6/8/2000 5:00:00 PM
File '..\System32\Drivers\1394bus.sys': Ver=4.90.3000.1, size=44240 bytes, created 6/8/2000 5:00:00 PM
File '..\System32\Drivers\Ohci1394.sys': Ver=4.90.3000.1, size=49488 bytes, created 6/8/2000 5:00:00 PM
File '..\System32\Drivers\Sbp2port.sys': Ver=4.90.3000.1, size=36336 bytes, created 6/8/2000 5:00:00 PM
File 'IoSubsys\Disktsd.vxd': Ver=4.90.3000, size=18663 bytes, created 6/8/2000 5:00:00 PM
Registry Keys:
This message has been edited since posting. Last time this message was edited on 14. August 2005 @ 18:54
|
Moderator
|
14. August 2005 @ 22:08 |
Link to this message
|
see here for more info on how to upgrade your firmware. the obvious scary warning applies here, don't power off or reset pc until it's finished or tyour burner might be toast - http://forum.rpc1.org/viewtopic.php?p=37412#37417
Quote:
Physical memory : 510MB (522636kB)
Free physical memory: 0MB (412kB)
Memory in use : 62 %
- there'll be a big problem, you've run out of memory, you gotta free up as much memory as you can prior to any burns. your hard disc will be 'swapping' and that's also bad for any disc work
Quote:
Finalize CD : FALSE
Multisession : TRUE
Multisession type: : Start multisession
- fyi, did you intend to do a multisession disc.
Quote:
End of disc reached
- that sounds obvious......
Quote:
Last possible write address on media: 359845 ( 79:59.70)
Last address to be written: 348352 ( 77:26.52)
- ....however it doesn't seem your using whole disc. See what i said about memory, this is probably a red herring...
and don't forget to look at anything i mentioned before if you're still having problems..
Main PC ~ Intel C2Q Q6600 (G0 Stepping)/Gigabyte GA-EP45-DS3/2GB Crucial Ballistix PC2-8500/Zalman CNPS9700/Antec 900/Corsair HX 620W
Network ~ DD-WRT ~ 2node WDS-WPA2/AES ~ Buffalo WHR-G54S. 3node WPA2/AES ~ WRT54GS v6 (inc. WEP BSSID), WRT54G v2, WRT54G2 v1. *** Forum Rules ***
|
|
givafuc
Newbie
|
15. August 2005 @ 12:03 |
Link to this message
|
Alright, I tried to upgrade the firmware- it isn't working, still the same old one. I used sfdnwin.exe and not the recommended one, but I don't know how to make a back up disk, never had to do one before.
Why would give me the end of disc reached error if I had room to go?
I don't understand "however it doesn't seem your using whole disc. See what i said about memory, this is probably a red herring...
" What do you mean by red herring? I can try again to burn another disc with 85%+ system resources free, but I tried to simulate before I burned this last one and it cleared- then while doing the real thing right after it, it naturally screws up another one of my cds.
I'm gonna step away from this cpu for a couple of hours, before I turn into that famous guy in that video of him slamming his fists down on his keyboard and finally grabbing it and hitting the monitor with it. Hehehehe.
But really I'm stumped and it pisses me off. I just don't get how I could be running everything so fine before I upgraded to this new version. I didn't have any failures due to discs supposedlly full when their not, firmware out of date, out of memory, other files conflicts with Nero. None of that. None. Until now I guess. WTF?
Sorry for my rantings.
|
Moderator
|
15. August 2005 @ 14:39 |
Link to this message
|
|
no worries, it does get frustratin when stuff don't work. if the sfdnwin.exe program doesn't work there is one or more alternative dos (command line) versions that are further up the page in that link i provided earlier.
Running out of memory is real bad, you need to have sufficient free memory prior to doing any burning. close more programs down before burning anything.
Once you've followed all my suggestions you should be burning again..
Main PC ~ Intel C2Q Q6600 (G0 Stepping)/Gigabyte GA-EP45-DS3/2GB Crucial Ballistix PC2-8500/Zalman CNPS9700/Antec 900/Corsair HX 620W
Network ~ DD-WRT ~ 2node WDS-WPA2/AES ~ Buffalo WHR-G54S. 3node WPA2/AES ~ WRT54GS v6 (inc. WEP BSSID), WRT54G v2, WRT54G2 v1. *** Forum Rules ***
|
|
givafuc
Newbie
|
15. August 2005 @ 17:39 |
Link to this message
|
|
Stupid Question Alert:
Is there a way to the sfdnwin.exe fix without doing a Boot disk?
I never done one before, if I can bypass it, I would, but really I don't have the time tonight to learn like I should, but if I have to, I will learn tomorrow. I know, that was a run-on sentence. Anyway, I will wait for stupid answers to my stupid question. Just joking :)
|
|
Advertisement
|
|
|
|
givafuc
Newbie
|
16. August 2005 @ 03:19 |
Link to this message
|
|
Hey creaky, check this log out. It was successful and the log is bascily the same as the failure logs. This CR-RW has a limit of 650MB and I burned only two episodes on it totally about 600MB, I think. Anyway, it worked. Here's the log:
Windows 98 4.90 (ME)
IA32
WinAspi: File 'Wnaspi32.dll': Ver=1, 0, 0, 0, size=36864 bytes, created 6/8/2000 5:00:00 PM
ahead WinASPI: File 'C:\PROGRAM FILES\AHEAD\NERO\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 10/26/2004 6:35:34 PM
Nero Version: 6.6.0.16
Internal Version: 6, 6, 0, 16b
Recorder: <SAMSUNG CD-R/RW SW-208B> Version: BT02 - HA 0 TA 1 - 6.6.0.16
Adapter driver: <ESDI_506> HA 0
Drive buffer : 4096kB
Bus Type : default (0) -> ATAPI, detected: ATAPI
CD-ROM: <SAMSUNG CD-ROM SC-148 >Version: ST01 - HA 0 TA 0 - 6.6.0.16
Adapter driver: <ESDI_506> HA 0
SAMSUNG CD-ROM SC-148 (Target 0, D:): Autoinsert Off, DMA On, Disconnect ?, SyncDataXfer ?
SAMSUNG CD-R/RW SW-208B (Target 1, E:): Autoinsert Off, DMA On, Disconnect ?, SyncDataXfer ?
Excluded drive IDs:
WriteBufferSize: 74448896 (0) Byte
ShowDrvBufStat : 0
BUFE : 0
Physical memory : 510MB (522636kB)
Free physical memory: 0MB (76kB)
Memory in use : 65 %
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)
16.8.2005
CD-ROM (ISO)
7:01:05 AM #1 Text 0 File Isodoc.cpp, Line 6356
Iso document burn settings
------------------------------------------
Determine maximum speed : FALSE
Simulate : FALSE
Write : TRUE
Finalize CD : FALSE
Multisession : FALSE
Burning mode : TAO
Mode : 1
ISO Level : 1 (Max. of 11 = 8 + 3 char)
Character set : ISO 9660
Joliet : TRUE
Allow pathdepth more than 8 directories : TRUE
Allow more than 255 characters in path : TRUE
Write ISO9660 ;1 file extensions : TRUE
7:01:05 AM #2 Text 0 File Reader.cpp, Line 127
Reader running
7:01:05 AM #3 Text 0 File Writer.cpp, Line 122
Writer SAMSUNG CD-R/RW SW-208B running
7:01:05 AM #4 ISO9660GEN -11 File geniso.cpp, Line 3309
First writeable address = 0 (0x00000000)
7:01:05 AM #5 Text 0 File Burncd.cpp, Line 3233
Turn on Track-At-Once, using CD-R/RW media
7:01:05 AM #6 Text 0 File DlgWaitCD.cpp, Line 270
Last possible write address on media: 337348 ( 74:59.73)
Last address to be written: 231916 ( 51:34.16)
7:01:05 AM #7 Text 0 File DlgWaitCD.cpp, Line 282
Write in overburning mode: NO (enabled: CD)
7:01:05 AM #8 Text 0 File DlgWaitCD.cpp, Line 2483
Recorder: SAMSUNG CD-R/RW SW-208B;
CDRW code: 00 97 26 48; OSJ entry from: FUJI Photo Film Co., Ltd.
ATIP Data: ?
7:01:05 AM #9 Text 0 File DlgWaitCD.cpp, Line 448
>>> Protocol of DlgWaitCD activities: <<<
=========================================
7:01:05 AM #10 Text 0 File ThreadedTransferInterface.cpp, Line 838
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
2 indices, index0 (150) not provided
original disc pos #0 + 231917 (231917) = #231917/51:32.17
relocatable, disc pos for caching/writing not required/ required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 231915 blocks [SAMSUNG CD-R/RW SW-208B]
--------------------------------------------------------------
7:01:05 AM #11 Text 0 File ThreadedTransferInterface.cpp, Line 1051
Prepare recorder [SAMSUNG CD-R/RW SW-208B] for write in TAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc not fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 307200 475273216, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________
-150 | lead-in | 0 | 0x41 | 0x00
-150 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
231917 | lead-out | 1 | 0x41 | 0x00
7:01:05 AM #12 Text 0 File ThreadedTransferInterface.cpp, Line 1119
Removed 2 run-out blocks from end of track 1. Length: 231917 -> 231915.
7:01:06 AM #13 Phase 24 File dlgbrnst.cpp, Line 1832
Caching of files started
7:01:06 AM #14 Text 0 File Burncd.cpp, Line 4120
Cache writing successful.
7:01:06 AM #15 Phase 25 File dlgbrnst.cpp, Line 1832
Caching of files completed
7:01:06 AM #16 Phase 36 File dlgbrnst.cpp, Line 1832
Burn process started at 4x (600 KB/s)
7:01:06 AM #17 Text 0 File ThreadedTransferInterface.cpp, Line 2654
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0
7:14:04 AM #18 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion
7:14:10 AM #19 Text 0 File Mmc.cpp, Line 16352
<SAMSUNG CD-R/RW SW-208B > start Close Session
7:15:42 AM #20 Phase 37 File dlgbrnst.cpp, Line 1832
Burn process completed successfully at 4x (600 KB/s)
Existing drivers:
File 'IoSubSys\SCSI1HLP.VXD': Ver=4.90.3000, size=19278 bytes, created 6/8/2000 5:00:00 PM
File 'IoSubsys\NEROCD95.VXD': Ver=4.5.0.14, size=39882 bytes, created 3/11/2002 11:55:38 AM
File 'IoSubsys\CDR4VSD.VXD': Ver=5.3.2.31, size=101616 bytes, created 3/1/2003 8:08:58 PM
File 'IoSubsys\CDRALVSD.VXD': Ver=5.3.2.31, size=20043 bytes, created 3/1/2003 8:08:58 PM
File 'IoSubsys\CDFS.VXD': Ver=4.90.3000, size=59141 bytes, created 6/8/2000 5:00:00 PM
File 'IoSubsys\ESDI_506.PDR': Ver=4.90.3000, size=25365 bytes, created 6/8/2000 5:00:00 PM
File 'IoSubsys\USBMPHLP.PDR': Ver=4.90.3000, size=4861 bytes, created 6/8/2000 5:00:00 PM
File '..\System32\Drivers\1394bus.sys': Ver=4.90.3000.1, size=44240 bytes, created 6/8/2000 5:00:00 PM
File '..\System32\Drivers\Ohci1394.sys': Ver=4.90.3000.1, size=49488 bytes, created 6/8/2000 5:00:00 PM
File '..\System32\Drivers\Sbp2port.sys': Ver=4.90.3000.1, size=36336 bytes, created 6/8/2000 5:00:00 PM
File 'IoSubsys\Disktsd.vxd': Ver=4.90.3000, size=18663 bytes, created 6/8/2000 5:00:00 PM
Registry Keys:
Go figure...
|
|
