|
|
|
Problem burning with Nero to my USB connected LG writer
|
|
|
feromone
Suspended due to non-functional email address
|
6. October 2005 @ 10:58 |
Link to this message
|
|
I have major problems burning with Nero (and DVDShrink). I have a LG 4163-B DVD writer connected by USB to my HP ze5300 laptop which will not allow me to burn copies of DVD movies. I can do data disks okay.
I thought it was a problem with either the ASPI file or the firmware for the DVD unit - as suggested on this site. The real problems started after I put new firmware into the LG writer and loaded the updated ASPI file into the PC. The Toshiba SD-R2132 DVD-Rom on my laptop now no longer recognises CDs or DVDs. XP says there is no problem.
Tried to roll back to a previous driver, but that didn't work - it asked me to find one on the system or a CD - I don't have the driver as a backup anywhere, not even on the system disks. I went to the Toshiba site to see if they had a driver for the unit on my laptop and I couldn't find one (it's a SD-R2312).
As for burning DVD movies on the LG, every time it comes to burning the log window says "SCSI command aborted" and stops after 1%. I've ruined several DVD-R's this way.
My problems are:
1. How do I get my laptop's DVD-Rom back up and running properly?
2. How do I solve the problem of burning to the LG writer?
Is it a.) a software problem b.) a hardware problem, c.) both.??
Can anybody help pls? I'm losing my rag! :-[
|
|
Advertisement
|
 |
|
|
Moderator
|
9. October 2005 @ 11:59 |
Link to this message
|
|
hi. i may very well buy this very same burner this week, to house in my Belkin USB2 enclosure. i've been umming and ahhing over this for ages as i read too many bad things about USB burning but my enclosures work brilliantly for ALL my ripping as i have a CD Burner/DVD-Rom combo drive in one of the Belkins and it works perfectly for ripping and burning CD's.
Even if i don't buy one i'll have a look into your problem...
Main PC ~ Intel C2Q Q6600 (G0 Stepping)/Gigabyte GA-EP45-DS3/2GB Crucial Ballistix PC2-8500/Zalman CNPS9700/Antec 900/Corsair HX 620W
Network ~ DD-WRT ~ 2node WDS-WPA2/AES ~ Buffalo WHR-G54S. 3node WPA2/AES ~ WRT54GS v6 (inc. WEP BSSID), WRT54G v2, WRT54G2 v1. *** Forum Rules *** |
|
feromone
Suspended due to non-functional email address
|
10. October 2005 @ 12:00 |
Link to this message
|
|
Thanks, :o) a friend suggested updating the USB drivers - but it's a Via Rev 5 Universal Host Companion Controller and there's no updated driver available. Maybe reinstalling might do something??
|
|
feromone
Suspended due to non-functional email address
|
11. October 2005 @ 11:16 |
Link to this message
|
|
OK! Got the Toshiba DVD up and working again, so that's one part of the problem solved. Found the driver for it on my PC in the Windows directory.
Still not solved LG burning problem.
|
|
feromone
Suspended due to non-functional email address
|
20. October 2005 @ 10:11 |
Link to this message
|
|
hellooooooooo... can anyone help or offer suggestion?
|
Moderator
|
20. October 2005 @ 10:50 |
Link to this message
|
|
right. i have another LG 4167B on order so tomorrow it'll be in my USB2 enclosure this time tomorrow but i'm confident it'll be fine in the enclosure. i have an LG dvd-rom/cd writer combo drive housed in my other USB2 enclosure and that's ripped like 2000 movies while living in said enclosure.
what burning program you using ?, and have yout got USB2 ? as USB1 won't cut it from what i remember
Main PC ~ Intel C2Q Q6600 (G0 Stepping)/Gigabyte GA-EP45-DS3/2GB Crucial Ballistix PC2-8500/Zalman CNPS9700/Antec 900/Corsair HX 620W
Network ~ DD-WRT ~ 2node WDS-WPA2/AES ~ Buffalo WHR-G54S. 3node WPA2/AES ~ WRT54GS v6 (inc. WEP BSSID), WRT54G v2, WRT54G2 v1. *** Forum Rules ***
|
|
feromone
Suspended due to non-functional email address
|
22. October 2005 @ 07:51 |
Link to this message
|
Yeah, using a HP Pavilion laptop 5350 series - 512Mb of memory, 2.80 Ghz pentium IV. Using Nero 6.3.1.6.
It's funny you should mention it, but I have two USB 2.0 ports on the back, and a USB port for the mouse. However... once or twice when it failed to burn it said the device would not work as it wasn't plugged into a hi-speed port.
I've always used the USB 2.0 ports at the back, so why would this happen? It's F&(cked! PCs are moody b**stards. If it would help you I can try burning again and then post the log here.
|
Moderator
|
22. October 2005 @ 09:02 |
Link to this message
|
|
yup, logfile would be good. i ended up having a 4163B delivered instead of the 4167B but that's a great drive and it's in my USB2 enclosure; it's now done quite a few rips and also quite a few faultless burns so far via the 4163B thru USB2...
Main PC ~ Intel C2Q Q6600 (G0 Stepping)/Gigabyte GA-EP45-DS3/2GB Crucial Ballistix PC2-8500/Zalman CNPS9700/Antec 900/Corsair HX 620W
Network ~ DD-WRT ~ 2node WDS-WPA2/AES ~ Buffalo WHR-G54S. 3node WPA2/AES ~ WRT54GS v6 (inc. WEP BSSID), WRT54G v2, WRT54G2 v1. *** Forum Rules ***
This message has been edited since posting. Last time this message was edited on 22. October 2005 @ 09:03
|
|
feromone
Suspended due to non-functional email address
|
26. October 2005 @ 09:38 |
Link to this message
|
Okay, the log file for Nero is below. Hope this helps cos' I just keep ruining DVDs... :(
Windows XP 5.1
IA32
WinAspi: File 'Wnaspi32.dll': Ver=4.71 (0002), size=45056 bytes, created 17/07/2002 10:03:20
ahead WinASPI: File 'C:\Program Files\Ahead\nero\Wnaspi32.dll': Ver=2.0.1.59, size=160016 bytes, created 16/12/2003 19:18:06
Nero version: 6.3.1.6
Recorder: <HL-DT-ST DVDRAM GSA-4163B>Version: A104 - HA 2 TA 0 - 6.3.1.6
Adapter driver: <> HA 2
Drive buffer : 2048kB
Bus Type : via Inquiry data (1) -> ATAPI, detected: ?
Connected to MMC as unknown drive with class-nr : 11
Drive is autodetected - recorder class: DVD+R9 DL recorder
CD-ROM: <TOSHIBA DVD-ROM SD-R2312>Version: 1905 - HA 1 TA 0 - 6.3.1.6
Adapter driver: <atapi> HA 1
=== Scsi-Device-Map ===
DiskPeripheral : IC25N040ATCS04-0 atapi Port 0 ID 0 DMA: On
CdRomPeripheral : TOSHIBA DVD-ROM SD-R2312 atapi Port 1 ID 0 DMA: On
=== CDRom-Device-Map ===
TOSHIBA DVD-ROM SD-R2312 D: CDRom0
HL-DT-ST DVDRAM GSA-4163 E: CDRom1
=======================
AutoRun : 1
Excluded drive IDs:
CmdQueuing : 1
CmdNotification: 2
WriteBufferSize: 66060288 (0) Byte
ShowDrvBufStat : 0
EraseSpeed : 0
BUFE : 0
Physical memory : 446MB (457712kB)
Free physical memory: 122MB (125740kB)
Memory in use : 72 %
Uncached PFiles: 0x0
Use Static Write Speed Table: 0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)
26.10.2005
UDF/ISO compilation
18:28:28 #1 Phase 112 File dlgbrnst.cpp, Line 1841
DVD-Video files reallocation started
18:28:28 #2 Phase 114 File dlgbrnst.cpp, Line 1841
DVD-Video files reallocation completed (no file modified)
18:28:28 #3 Text 0 File Isodoc.cpp, Line 6062
Iso document burn settings
------------------------------------------
Determine maximum speed : FALSE
Simulate : FALSE
Write : TRUE
Finalize CD : TRUE
Multisession : FALSE
Burning mode : DAO
Mode : 1
ISO Level : 1 (Max. of 11 = 8 + 3 char)
Character set : ISO 9660
Joliet :FALSE
Allow pathdepth more than 8 directories : FALSE
Allow more than 255 characters in path : FALSE
Write ISO9660 ;1 file extensions : TRUE
18:28:28 #4 Phase 111 File dlgbrnst.cpp, Line 1841
DVD-Video files sorted
18:28:28 #5 Text 0 File Reader.cpp, Line 118
Reader running
18:28:28 #6 Text 0 File Writer.cpp, Line 124
Writer HL-DT-ST DVDRAM GSA-4163B running
18:28:28 #7 ISO9660GEN -11 File geniso.cpp, Line 3898
First writeable address = 0 (0x00000000)
18:28:28 #8 ISO9660GEN -11 File geniso.cpp, Line 3898
First writeable address = 0 (0x00000000)
18:28:29 #9 Text 0 File Burncd.cpp, Line 3198
Turn on Disc-at-once, using DVD media
18:28:29 #10 Text 0 File DlgWaitCD.cpp, Line 244
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 2202143 (489:21.68, 4301MB)
18:28:29 #11 Text 0 File DlgWaitCD.cpp, Line 249
Write in overburning mode: FALSE
18:28:29 #12 Text 0 File DlgWaitCD.cpp, Line 2107
Recorder: HL-DT-ST DVDRAM GSA-4163B, Media type: DVD-R
Disc Manufacturer: MCC 02 - RG20
Disc Application Code: 64, Disc Physical Code: 193
18:28:29 #13 Text 0 File DlgWaitCD.cpp, Line 410
>>> Protocol of DlgWaitCD activities: <<<
=========================================
18:28:29 #14 Text 0 File ThreadedTransferInterface.cpp, Line 813
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 (CTransferItem)
2 indices, index0 (150) not provided
original disc pos #0 + 2202144 (2202144) = #2202144/489:21.69
relocatable, disc pos for caching/writing not required/required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2202144 blocks [HL-DT-ST DVDRAM GSA-4163B]
--------------------------------------------------------------
18:28:29 #15 Text 0 File ThreadedTransferInterface.cpp, Line 982
Prepare recorder [HL-DT-ST DVDRAM GSA-4163B] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4509990912, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_RecDep_|_CtrlAdr_
0 | lead-in | 0 | 0x00 | 0x41
0 | 1 | 0 | 0x00 | 0x41
0 | 1 | 1 | 0x00 | 0x41
2202144 | lead-out | 1 | 0x00 | 0x41
18:28:29 #16 Phase 24 File dlgbrnst.cpp, Line 1841
Caching of files started
18:28:29 #17 Text 0 File Burncd.cpp, Line 4214
Cache writing successful.
18:28:29 #18 Phase 25 File dlgbrnst.cpp, Line 1841
Caching of files completed
18:28:29 #19 Phase 36 File dlgbrnst.cpp, Line 1841
Burn process started at 4x (5,520 KB/s)
18:28:29 #20 Text 0 File ThreadedTransferInterface.cpp, Line 2342
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0
18:28:30 #21 Text 0 File dlgbrnst.cpp, Line 1699
Set remaining time: 13:39,960 (819960ms) -> OK
18:28:30 #22 Text 0 File DVDR.cpp, Line 1619
Recording mode: Sequential Recording Mode
18:28:30 #23 Text 0 File Mmc.cpp, Line 19864
Set BUFE: supported -> ON
18:28:30 #24 Text 0 File DVDR.cpp, Line 1760
Start write address at LBA 0
DVD high compatibility mode: Yes
18:28:30 #25 Text 0 File Cdrdrv.cpp, Line 8002
---- DVD Structure: Physical Format Information (00h) ----
Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 5
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 26127F h
End Sector Number in Layer 0: 0 h
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 2FE10 h
Start sector number of the next Border-In: 2FFA0 h
Media Specific [16..63]:
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
00 02 FE 10 00 02 FF A0 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
18:28:49 #26 SCSI -500 File Cdrdrv.cpp, Line 1437
SCSI Exec, HA 2, TA 0, LUN 0, buffer 0x03AB0000
Status: 0x02 (0x03, SCSI_ABORTED)
HA-Status 0x10 (0x0A, SCSI_HASTAT_REQUEST_SENSE_FAILED)
TA-Status 0x00 (0x00, OK)
Sense Key: 0x05 (KEY_ILLEGAL_REQUEST)
Sense Code: 0x26
Sense Qual: 0x02
CDB Data: 0x2A 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x10 0x00 0x00 0x00
Sense Data: 0xF0 0x00 0x05 0x00 0x00 0x00 0x00 0x00
0x00 0x00 0x00 0x00 0x26 0x02
18:28:49 #27 CDR -500 File Writer.cpp, Line 304
SCSI command aborted
HL-DT-ST DVDRAM GSA-4163B\H2 T0
18:28:50 #28 Text 0 File ThreadedTransfer.cpp, Line 229
all writers idle, stopping conversion
18:28:50 #29 Text 0 File ThreadedTransfer.cpp, Line 223
conversion idle, stopping reader
18:28:50 #30 Text 0 File DVDR.cpp, Line 1970
EndDAO: Last written address was -1
18:28:50 #31 Text 0 File dlgbrnst.cpp, Line 1699
Set remaining time: 0:00,000 (0ms) -> OK
18:28:50 #32 Text 0 File dlgbrnst.cpp, Line 1699
Set remaining time: 0:00,000 (0ms) -> OK
18:28:50 #33 Phase 38 File dlgbrnst.cpp, Line 1841
Burn process failed at 4x (5,520 KB/s)
Existing drivers:
File 'Drivers\CDRALW2K.SYS': Ver=5.3.4.21, size=23436 bytes, created 17/12/2002 12:32:46
File 'Drivers\ASPI32.SYS': Ver=4.71 (0002) built by: WinDDK, size=16512 bytes, created 17/07/2002 09:05:10
File 'Drivers\PXHELP20.SYS': Ver=2.03.18a, size=20576 bytes, created 18/03/2005 22:49:39 (Prassi/Veritas driver for win 2K)
File 'Drivers\atapi.sys': Ver=5.1.2600.1106 (xpsp1.020828-1920), size=86912 bytes, created 29/08/2002 04:27:50 (Adapter driver for src)
Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
|
Moderator
|
26. October 2005 @ 10:44 |
Link to this message
|
Quote:
Nero version: 6.3.1.6
- Nero's too old, update (free) to latest 6.x version - 6.6.0.16. get 'Update-Package 1' from here - http://www.nero.com/nero6/en/nero-up.php
Quote:
Recorder: <HL-DT-ST DVDRAM GSA-4163B>Version: A104
- firmware is one version out of date, A105 is here - http://forum.rpc1.org/dl_firmware.php?download_id=1973
Quote:
Connected to MMC as unknown drive with class-nr : 11
Drive is autodetected - recorder class: DVD+R9 DL recorder
- yup, Nero's too old to recognise your burner
Quote:
Physical memory : 446MB (457712kB)
Free physical memory: 122MB (125740kB)
Memory in use : 72 %
- try to close down more programs to ensure sufficient free memory prior to all burning
Quote:
Existing drivers:
File 'Drivers\CDRALW2K.SYS': Ver=5.3.4.21, size=23436 bytes, created 17/12/2002 12:32:46
- get rid of Roxio, plus to fully remove it you may need to google search for 'Roxio Zapper'
Main PC ~ Intel C2Q Q6600 (G0 Stepping)/Gigabyte GA-EP45-DS3/2GB Crucial Ballistix PC2-8500/Zalman CNPS9700/Antec 900/Corsair HX 620W
Network ~ DD-WRT ~ 2node WDS-WPA2/AES ~ Buffalo WHR-G54S. 3node WPA2/AES ~ WRT54GS v6 (inc. WEP BSSID), WRT54G v2, WRT54G2 v1. *** Forum Rules ***
This message has been edited since posting. Last time this message was edited on 26. October 2005 @ 10:44
|
|
feromone
Suspended due to non-functional email address
|
27. October 2005 @ 11:28 |
Link to this message
|
Update: Tried my burner to make a data disc last night, and it didn't work - thanks for the tip on Nero, going to update and see how it works.
The firmware update you mentioned is for Windows ME according to LG updates.
What's the problem with Roxio? I can remove it, but I didn't realise it was causing a problem.
As for the memory, are you saying shut down in Task Manager? (I don't run a lot of programs concurrently.)
Cheers for your help
|
Moderator
|
27. October 2005 @ 11:45 |
Link to this message
|
Main PC ~ Intel C2Q Q6600 (G0 Stepping)/Gigabyte GA-EP45-DS3/2GB Crucial Ballistix PC2-8500/Zalman CNPS9700/Antec 900/Corsair HX 620W
Network ~ DD-WRT ~ 2node WDS-WPA2/AES ~ Buffalo WHR-G54S. 3node WPA2/AES ~ WRT54GS v6 (inc. WEP BSSID), WRT54G v2, WRT54G2 v1. *** Forum Rules ***
|
AfterDawn Addict
|
27. October 2005 @ 12:02 |
Link to this message
|
|
just a tip,i had problems with burning dvd with my laptop with my external burner..
how i solved the problem i went and got a Adaptec AUA-1420 USB 2.0 2 Port Card and had not a problem burning again..
|
|
feromone
Suspended due to non-functional email address
|
28. October 2005 @ 11:33 |
Link to this message
|
Updated the Nero Burning as suggested. Had minimal success so far. Now I seem to have a different error msg.
It now says "illegal disc" when it fails to burn - been trying to break it in slowly by burning data discs. Hit rate to date is "ruined 5 - burned 1". Wow.
Memory is still allocating a lot to programs which aren't running - how can I stop this apart from going into task manager and shutting them down (which basically says that shutting them down can affect system stability)?
Think the idea of a USB 2.0 card is something, but b4 I purchase (and waste more money - which this LG burner is feeling like £80 down the gurgler) can you give me more details on why this would work?
Just to be a completist, here's the log from one of the "illegal disc" failures... Thanx.
Windows XP 5.1
IA32
WinAspi: File 'Wnaspi32.dll': Ver=4.71 (0002), size=45056 bytes, created 17/07/2002 10:03:20
ahead WinASPI: File 'C:\Program Files\Ahead\nero\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 26/10/2004 18:35:34
Nero Version: 6.6.0.16
Internal Version: 6, 6, 0, 16b
Recorder: <HL-DT-ST DVDRAM GSA-4163B>Version: A104 - HA 2 TA 0 - 6.6.0.16
Adapter driver: <> HA 2
Drive buffer : 2048kB
Bus Type : default (0) -> ATAPI, detected: ?
CD-ROM: <TOSHIBA DVD-ROM SD-R2312>Version: 1905 - HA 1 TA 0 - 6.6.0.16
Adapter driver: <atapi> HA 1
=== Scsi-Device-Map ===
DiskPeripheral : IC25N040ATCS04-0 atapi Port 0 ID 0 DMA: On
CdRomPeripheral : TOSHIBA DVD-ROM SD-R2312 atapi Port 1 ID 0 DMA: On
=== CDRom-Device-Map ===
TOSHIBA DVD-ROM SD-R2312 D: CDRom0
HL-DT-ST DVDRAM GSA-4163B E: CDRom1
=======================
AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 66060288 (0) Byte
ShowDrvBufStat : 0
BUFE : 0
Physical memory : 446MB (457712kB)
Free physical memory: 110MB (113064kB)
Memory in use : 75 %
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)
28.10.2005
ISO compilation
20:14:10 #1 Text 0 File Isodoc.cpp, Line 6356
Iso document burn settings
------------------------------------------
Determine maximum speed : FALSE
Simulate : FALSE
Write : TRUE
Finalize CD : TRUE
Multisession : FALSE
Burning mode : DAO
Mode : 1
ISO Level : 1 (Max. of 11 = 8 + 3 char)
Character set : ISO 9660
Joliet : TRUE
Allow pathdepth more than 8 directories : FALSE
Allow more than 255 characters in path : FALSE
Write ISO9660 ;1 file extensions : TRUE
20:14:10 #2 Text 0 File Reader.cpp, Line 127
Reader running
20:14:10 #3 Text 0 File Writer.cpp, Line 122
Writer HL-DT-ST DVDRAM GSA-4163B running
20:14:10 #4 ISO9660GEN -11 File geniso.cpp, Line 3309
First writeable address = 0 (0x00000000)
20:14:10 #5 Text 0 File Burncd.cpp, Line 3233
Turn on Disc-At-Once, using DVD media
20:14:11 #6 Text 0 File DlgWaitCD.cpp, Line 270
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 2201455 (489:12.55, 4299MB)
20:14:11 #7 Text 0 File DlgWaitCD.cpp, Line 282
Write in overburning mode: NO (enabled: CD)
20:14:11 #8 Text 0 File DlgWaitCD.cpp, Line 2483
Recorder: HL-DT-ST DVDRAM GSA-4163B, Media type: DVD-R
Disc Manufacturer: MCC 02 - RG20
Disc Application Code: 64, Disc Physical Code: 193
20:14:11 #9 Text 0 File DlgWaitCD.cpp, Line 448
>>> Protocol of DlgWaitCD activities: <<<
=========================================
20:14:11 #10 Text 0 File ThreadedTransferInterface.cpp, Line 838
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
2 indices, index0 (150) not provided
original disc pos #0 + 2201456 (2201456) = #2201456/489:12.56
relocatable, disc pos for caching/writing not required/ required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2201456 blocks [HL-DT-ST DVDRAM GSA-4163B]
--------------------------------------------------------------
20:14:11 #11 Text 0 File ThreadedTransferInterface.cpp, Line 1051
Prepare recorder [HL-DT-ST DVDRAM GSA-4163B] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4508581888, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
2201456 | lead-out | 1 | 0x41 | 0x00
20:14:11 #12 Phase 24 File dlgbrnst.cpp, Line 1832
Caching of files started
20:14:11 #13 Text 0 File Burncd.cpp, Line 4120
Cache writing successful.
20:14:11 #14 Phase 25 File dlgbrnst.cpp, Line 1832
Caching of files completed
20:14:11 #15 Phase 36 File dlgbrnst.cpp, Line 1832
Burn process started at 8x (11,080 KB/s)
20:14:11 #16 Text 0 File ThreadedTransferInterface.cpp, Line 2654
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0
20:14:12 #17 Text 0 File DVDR.cpp, Line 2379
Recording mode: Sequential Recording Mode
20:14:12 #18 Text 0 File Mmc.cpp, Line 21708
Set BUFE: Buffer underrun protection -> ON
20:14:12 #19 Text 0 File DVDR.cpp, Line 2534
Start write address at LBA 0
DVD high compatibility mode: Yes
20:14:12 #20 Text 0 File Cdrdrv.cpp, Line 8862
---- DVD Structure: Physical Format Information (00h) ----
Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 0.0 (0)
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 26127F h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 2FE10 h
Start sector number of the next Border-In: 2FFA0 h
Media Specific [16..63]:
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
00 02 FE 10 00 02 FF A0 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
20:14:44 #21 SCSI -500 File Cdrdrv.cpp, Line 1434
SCSI Exec, HA 2, TA 0, LUN 0, buffer 0x04270000
Status: 0x02 (0x03, SCSI_ABORTED)
HA-Status 0x10 (0x0A, SCSI_HASTAT_REQUEST_SENSE_FAILED)
TA-Status 0x00 (0x00, OK)
Sense Key: 0x05 (KEY_ILLEGAL_REQUEST)
Sense Code: 0x26
Sense Qual: 0x02
CDB Data: 0x2A 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x20 0x00 0x00 0x00
Sense Data: 0xF0 0x00 0x05 0x00 0x00 0x00 0x00 0x00
0x00 0x00 0x00 0x00 0x26 0x02
20:14:44 #22 SCSI -1046 File Cdrdrv.cpp, Line 1434
SCSI Exec, HA 2, TA 0, LUN 0, buffer 0x04AF1400
Status: 0x04 (0x01, SCSI_ERR)
HA-Status 0x00 (0x00, OK)
TA-Status 0x02 (0x01, SCSI_TASTATUS_CHKCOND)
Sense Key: 0x05 (KEY_ILLEGAL_REQUEST)
Sense Code: 0x30
Sense Qual: 0x05
CDB Data: 0x2A 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x20 0x00 0x00 0x00
Sense Data: 0x70 0x00 0x05 0x00 0x00 0x00 0x00 0x10
0x2A 0x00 0x00 0x0C 0x30 0x05
20:14:44 #23 CDR -1046 File Writer.cpp, Line 311
Illegal disc
20:14:44 #24 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion
20:14:45 #25 Text 0 File ThreadedTransfer.cpp, Line 222
conversion idle, stopping reader
20:14:45 #26 Text 0 File DVDR.cpp, Line 2774
EndDAO: Last written address was -1
20:14:45 #27 Phase 38 File dlgbrnst.cpp, Line 1832
Burn process failed at 8x (11,080 KB/s)
Existing drivers:
File 'Drivers\CDRALW2K.SYS': Ver=5.3.4.21, size=23436 bytes, created 17/12/2002 12:32:46
File 'Drivers\ASPI32.SYS': Ver=4.71 (0002) built by: WinDDK, size=16512 bytes, created 17/07/2002 09:05:10
File 'Drivers\PXHELP20.SYS': Ver=2.03.18a, size=20576 bytes, created 18/03/2005 22:49:39 (Prassi/Veritas driver for win 2K)
File 'Drivers\atapi.sys': Ver=5.1.2600.1106 (xpsp1.020828-1920), size=86912 bytes, created 29/08/2002 04:27:50 (Adapter driver for src)
Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
|
|
gzaloam
Account closed as per user's own request
|
15. November 2005 @ 13:58 |
Link to this message
|
I´ll apreciate if anyone can help me.
I recently bought a Zynet Enclosure (cd-r3-u2) and a LG 4167b dvd burner. The only issue i have is that if i try to burn a cd-r using the disc-at-once method, it fails in the "lead-in" step. I´d tried using several brands of media, and won´t work. Actually, i can burn cd-r's with track-at-once. I´m using Nero 6.6.0.16. Here's the log.
Windows XP 5.1
IA32
WinAspi: -
ahead WinASPI: File 'C:\Program Files\Ahead\Nero\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 10/26/2004 18:35:34
Nero Version: 6.6.0.16
Internal Version: 6, 6, 0, 16b
Recorder: <HL-DT-ST DVDRAM GSA-4167B>Version: DL12 - HA 3 TA 1 - 6.6.0.16
Adapter driver: <> HA 3
Drive buffer : 2048kB
Bus Type : default (0) -> ATAPI, detected: ?
CD-ROM: <AXV CD/DVD-ROM >Version: 2.2a - HA 2 TA 0 - 6.6.0.16
Adapter driver: <a347scsi> HA 2
=== Scsi-Device-Map ===
DiskPeripheral : SAMSUNG MP0603H atapi Port 0 ID 0 DMA: On
CdRomPeripheral : HL-DT-ST RW/DVD GCC-4241N atapi Port 1 ID 0 DMA: On
CdRomPeripheral : AXV CD/DVD-ROM 2.2a a347scsi Port 2 ID 0 DMA: Off
=== CDRom-Device-Map ===
HL-DT-ST RW/DVD GCC-4241N I: CDRom0
AXV CD/DVD-ROM J: CDRom1
HL-DT-ST DVDRAM GSA-4167B K: CDRom8
=======================
AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 83886080 (0) Byte
ShowDrvBufStat : 0
BUFE : 0
Physical memory : 638MB (654320kB)
Free physical memory: 258MB (264360kB)
Memory in use : 59 %
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)
15.11.2005
CD Image
15:54:46 #1 Text 0 File Burncd.cpp, Line 2948
HL-DT-ST DVDRAM GSA-4167B
Buffer underrun protection activated
15:54:46 #2 Text 0 File Reader.cpp, Line 127
Reader running
15:54:46 #3 Text 0 File Writer.cpp, Line 122
Writer HL-DT-ST DVDRAM GSA-4167B running
15:54:46 #4 Text 0 File Burncd.cpp, Line 3233
Turn on Disc-At-Once, using CD-R/RW media
15:54:46 #5 Text 0 File DlgWaitCD.cpp, Line 270
Last possible write address on media: 359848 ( 79:59.73)
Last address to be written: 76985 ( 17:08.35)
15:54:46 #6 Text 0 File DlgWaitCD.cpp, Line 282
Write in overburning mode: NO
15:54:46 #7 Text 0 File DlgWaitCD.cpp, Line 2483
Recorder: HL-DT-ST DVDRAM GSA-4167B;
CDRW code: 00 97 22 60; OSJ entry from: Daxon Technology, Inc.
ATIP Data:
Special Info [hex] 1: 00 00 00, 2: 00 00 00 (LI 0:00.00), 3: 00 00 00 (LO 0:00.00)
Additional Info [hex] 1: 00 00 00 (invalid), 2: 00 00 00 (invalid), 3: 00 00 00 (invalid)
15:54:46 #8 Text 0 File DlgWaitCD.cpp, Line 448
>>> Protocol of DlgWaitCD activities: <<<
=========================================
15:54:46 #9 Text 0 File ThreadedTransferInterface.cpp, Line 838
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 (2 - CD-ROM Mode 1, Joliet)
2 indices, index0 (150) not provided
original disc pos #0 + 76986 (76986) = #76986/17:6.36
relocatable, disc pos for caching/writing not required/not required, patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 76986 blocks [HL-DT-ST DVDRAM GSA-4167B]
--------------------------------------------------------------
15:54:46 #10 Text 0 File ThreadedTransferInterface.cpp, Line 1051
Prepare recorder [HL-DT-ST DVDRAM GSA-4167B] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 307200 157974528, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________
-150 | lead-in | 0 | 0x41 | 0x00
-150 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
76986 | lead-out | 1 | 0x41 | 0x00
15:54:46 #11 Phase 24 File dlgbrnst.cpp, Line 1832
Caching of files started
15:54:46 #12 Text 0 File Burncd.cpp, Line 4120
Cache writing successful.
15:54:46 #13 Phase 25 File dlgbrnst.cpp, Line 1832
Caching of files completed
15:54:47 #14 Phase 36 File dlgbrnst.cpp, Line 1832
Burn process started at 4x (600 KB/s)
15:54:47 #15 Text 0 File ThreadedTransferInterface.cpp, Line 2654
Verifying disc position of item 0 (relocatable, no disc pos, patch infos, orig at #0): write at #0
15:54:47 #16 Text 0 File Mmc.cpp, Line 16924
StartDAO : CD-Text - Off
15:54:47 #17 Text 0 File Mmc.cpp, Line 21708
Set BUFE: Buffer underrun protection -> ON
15:54:47 #18 Text 0 File Mmc.cpp, Line 17211
CueData, Len=32
41 00 00 14 00 00 00 00
41 01 00 10 00 00 00 00
41 01 01 10 00 00 02 00
41 aa 01 14 00 11 08 24
15:54:51 #19 SCSI -500 File Cdrdrv.cpp, Line 1434
SCSI Exec, HA 3, TA 1, LUN 0, buffer 0x04B30000
Status: 0x02 (0x03, SCSI_ABORTED)
HA-Status 0x10 (0x0A, SCSI_HASTAT_REQUEST_SENSE_FAILED)
TA-Status 0x00 (0x00, OK)
Sense Key: 0x05 (KEY_ILLEGAL_REQUEST)
Sense Code: 0x26
Sense Qual: 0x02
CDB Data: 0x2A 0x00 0xFF 0xFF 0xFF 0x6A 0x00 0x00 0x20 0x00 0x00 0x00
Sense Data: 0xF0 0x00 0x05 0x00 0x00 0x00 0x00 0x00
0x00 0x00 0x00 0x00 0x26 0x02
15:54:51 #20 SCSI -1114 File Cdrdrv.cpp, Line 1434
SCSI Exec, HA 3, TA 1, LUN 0, buffer 0x04000200
Status: 0x04 (0x01, SCSI_ERR)
HA-Status 0x00 (0x00, OK)
TA-Status 0x02 (0x01, SCSI_TASTATUS_CHKCOND)
Sense Key: 0x06 (KEY_UNIT_ATTENTION)
Sense Code: 0x29
Sense Qual: 0x00
CDB Data: 0x2A 0x00 0xFF 0xFF 0xFF 0x6A 0x00 0x00 0x20 0x00 0x00 0x00
Sense Data: 0x70 0x00 0x06 0x00 0x00 0x00 0x00 0x10
0x00 0x00 0x00 0x90 0x29 0x00
15:54:51 #21 CDR -1114 File Writer.cpp, Line 311
Reset occurred
15:54:51 #22 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion
15:54:52 #23 Text 0 File ThreadedTransfer.cpp, Line 222
conversion idle, stopping reader
15:54:52 #24 Phase 38 File dlgbrnst.cpp, Line 1832
Burn process failed at 4x (600 KB/s)
Existing drivers:
File 'Drivers\CDRALW2K.SYS': Ver=6.1.1.17 , size=24698 bytes, created 7/17/2003 00:19:56
File 'Drivers\a347scsi.sys': Ver=3.47.0.0 built by: WinDDK, size=5248 bytes, created 4/30/2004 09:33:00 (Adapter driver for src)
Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
I also tried using Roxio 6 and Alcohol 120%, but it doesn't work either.
|
Moderator
|
16. November 2005 @ 00:14 |
Link to this message
|
@feromone - slightly late replying to this one.....who changed the calendar to November!
Quote:
Recorder: <HL-DT-ST DVDRAM GSA-4163B>Version: A104
- get updated to A105, i've been using that for a while now myself. try navigating from here - http://www.lge.com/support/software_gcsc.jsp - i can never find a direct link, but a few clicks from there and you'll find it...
Quote:
Bus Type : default (0) -> ATAPI, detected: ?
- as your burner is external to the PC that question mark is fine
Quote:
Physical memory : 446MB (457712kB)
Free physical memory: 110MB (113064kB)
Memory in use : 75 %
- try to close down more programs to ensure sufficient free memory prior to all burning
Quote:
Recorder: HL-DT-ST DVDRAM GSA-4163B, Media type: DVD-R
Disc Manufacturer: MCC 02 - RG20
Disc Application Code: 64, Disc Physical Code: 193
- very nice discs
Quote:
Illegal disc
- follow ALL suggestions
Quote:
Burn process failed at 8x (11,080 KB/s)
- try 4x. my 4167B won't do 8x, whether mounted internally or in one of my USB2.0 enclosures. however my 4163B nearly always does 8x fine (i prefer to do 4x but have been experimenting with 8x on the 4163B which lives in my other USB2.0 enclosure)
Quote:
Existing drivers:
File 'Drivers\CDRALW2K.SYS': Ver=5.3.4.21, size=23436 bytes, created 17/12/2002 12:32:46
-
CDRALW2K.SYS is part of Roxio. try uninstalling Roxio (doesn't always play well with Nero), then you might need to fully remove using Roxio Zapper - http://www.microadvantage.net/utilities
@gzaloam -
Quote:
Recorder: <HL-DT-ST DVDRAM GSA-4167B>Version: DL12
- firmware is up to date. see my comments in feromone's logfile reply. my 4167B in my opinion, is nowhere near as good as the 4163B, hopefully it will become a better drive with future firmware releases. mine always fails at the lead-in stage when i do 8x
Quote:
Bus Type : default (0) -> ATAPI, detected: ?
- as your burner is external to the PC that question mark is fine
Quote:
Recorder: HL-DT-ST DVDRAM GSA-4167B;
CDRW code: 00 97 22 60; OSJ entry from: Daxon Technology, Inc.
ATIP Data:
Special Info [hex] 1: 00 00 00, 2: 00 00 00 (LI 0:00.00), 3: 00 00 00 (LO 0:00.00)
Additional Info [hex] 1: 00 00 00 (invalid), 2: 00 00 00 (invalid), 3: 00 00 00 (invalid)
- if nothing else works maybe try different media, but first try mounting the burner internally if you can, to try to rule out the USB enclosure.
Quote:
Reset occurred
- see other suggestions
Quote:
Existing drivers:
File 'Drivers\CDRALW2K.SYS': Ver=6.1.1.17 , size=24698 bytes, created 7/17/2003 00:19:56
-
CDRALW2K.SYS is part of Roxio. try uninstalling Roxio (doesn't always play well with Nero), then you might need
to fully remove using Roxio Zapper - http://www.microadvantage.net/utilities
Main PC ~ Intel C2Q Q6600 (G0 Stepping)/Gigabyte GA-EP45-DS3/2GB Crucial Ballistix PC2-8500/Zalman CNPS9700/Antec 900/Corsair HX 620W
Network ~ DD-WRT ~ 2node WDS-WPA2/AES ~ Buffalo WHR-G54S. 3node WPA2/AES ~ WRT54GS v6 (inc. WEP BSSID), WRT54G v2, WRT54G2 v1. *** Forum Rules ***
|
|
gzaloam
Account closed as per user's own request
|
17. November 2005 @ 19:46 |
Link to this message
|
|
i've tried everything and it's still failling, the chipset is Genesys GL 811, How good is it? The only enclosures I seem to find in Mexico are zynet, cosmos and bytecc. The Bytecc comes in two models, one with firewire alone and the other is combo, Do the both of them have the oxford 911, how good is this chip?. Finally, will the enclosure work if i use a 6pin-4pin firewire cable?
Thanks.
|
Moderator
|
18. November 2005 @ 01:43 |
Link to this message
|
|
try mounting the burner internally if you can, to try to rule out the USB enclosure.
Main PC ~ Intel C2Q Q6600 (G0 Stepping)/Gigabyte GA-EP45-DS3/2GB Crucial Ballistix PC2-8500/Zalman CNPS9700/Antec 900/Corsair HX 620W
Network ~ DD-WRT ~ 2node WDS-WPA2/AES ~ Buffalo WHR-G54S. 3node WPA2/AES ~ WRT54GS v6 (inc. WEP BSSID), WRT54G v2, WRT54G2 v1. *** Forum Rules ***
|
|
goterps7
Junior Member
|
19. November 2005 @ 11:02 |
Link to this message
|
Creaky, maybe you can help me too. My external is a Plextor 716A. It used to work fine before my hard drive crashed. But all three of my attempts since have no worked to burn DVD-Rs. I have a brand new hard drive and had to reinstall all my burning software.
Here's my log file:
Windows XP 5.1
IA32
WinAspi: -
ahead WinASPI: File 'C:\Program Files\Ahead\nero\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 10/26/2004 5:35:34 PM
Nero Version: 6.6.0.16
Internal Version: 6, 6, 0, 16b
Recorder: <PLEXTOR DVDR PX-716A> Version: 1.03 - HA 1 TA 0 - 6.6.0.16
Adapter driver: <> HA 1
Drive buffer : 8192kB
Bus Type : default (0) -> ATAPI, detected: ?
CD-ROM: <PLEXTOR DVDR PX-716A >Version: 1.03 - HA 1 TA 0 - 6.6.0.16
Adapter driver: <> HA 1
=== Scsi-Device-Map ===
DiskPeripheral : TOSHIBA MK8025GAS atapi Port 0 ID 0 DMA: On
CdRomPeripheral : TEAC DW-224E atapi Port 1 ID 0 DMA: On
=== CDRom-Device-Map ===
PLEXTOR DVDR PX-716A E: CDRom2
=======================
AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 66060288 (0) Byte
ShowDrvBufStat : 0
BUFE : 0
Physical memory : 446MB (457712kB)
Free physical memory: 55MB (56344kB)
Memory in use : 87 %
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)
15.11.2005
ISO compilation
8:28:12 AM #1 Text 0 File Isodoc.cpp, Line 6356
Iso document burn settings
------------------------------------------
Determine maximum speed : FALSE
Simulate : FALSE
Write : TRUE
Finalize CD : FALSE
Multisession : TRUE
Multisession type: : Start multisession
Burning mode : DAO
Mode : 1
ISO Level : 1 (Max. of 11 = 8 + 3 char)
Character set : ISO 9660
Joliet : TRUE
Allow pathdepth more than 8 directories : TRUE
Allow more than 255 characters in path : TRUE
Write ISO9660 ;1 file extensions : TRUE
8:28:12 AM #2 Text 0 File Reader.cpp, Line 127
Reader running
8:28:12 AM #3 Text 0 File Writer.cpp, Line 122
Writer PLEXTOR DVDR PX-716A running
8:28:12 AM #4 ISO9660GEN -11 File geniso.cpp, Line 3309
First writeable address = 0 (0x00000000)
8:28:12 AM #5 Text 0 File Burncd.cpp, Line 3233
Turn on Disc-At-Once, using DVD media
8:28:13 AM #6 Text 0 File DlgWaitCD.cpp, Line 270
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 1941679 (431:29.04, 3792MB)
8:28:13 AM #7 Text 0 File DlgWaitCD.cpp, Line 282
Write in overburning mode: NO (enabled: CD)
8:28:13 AM #8 Text 0 File DlgWaitCD.cpp, Line 2483
Recorder: PLEXTOR DVDR PX-716A, Media type: DVD-R
Disc Manufacturer: TYG02 -
Disc Application Code: 64, Disc Physical Code: 193
8:28:13 AM #9 Text 0 File DlgWaitCD.cpp, Line 448
>>> Protocol of DlgWaitCD activities: <<<
=========================================
8:28:13 AM #10 Text 0 File ThreadedTransferInterface.cpp, Line 838
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
2 indices, index0 (150) not provided
original disc pos #0 + 1941680 (1941680) = #1941680/431:29.5
relocatable, disc pos for caching/writing not required/ required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 1941680 blocks [PLEXTOR DVDR PX-716A]
--------------------------------------------------------------
8:28:17 AM #11 Text 0 File ThreadedTransferInterface.cpp, Line 1051
Prepare recorder [PLEXTOR DVDR PX-716A] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc not fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 3976560640, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
1941680 | lead-out | 1 | 0x41 | 0x00
8:28:17 AM #12 Phase 24 File dlgbrnst.cpp, Line 1832
Caching of files started
8:28:18 AM #13 Text 0 File Burncd.cpp, Line 4120
Cache writing successful.
8:28:18 AM #14 Phase 25 File dlgbrnst.cpp, Line 1832
Caching of files completed
8:28:18 AM #15 Phase 36 File dlgbrnst.cpp, Line 1832
Burn process started at 8x (11,080 KB/s)
8:28:18 AM #16 Text 0 File ThreadedTransferInterface.cpp, Line 2654
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0
8:28:18 AM #17 Text 0 File DVDR.cpp, Line 2379
Recording mode: Sequential Recording Mode for Multisession
8:28:18 AM #18 Text 0 File Mmc.cpp, Line 21708
Set BUFE: BURN-Proof -> ON
8:28:18 AM #19 Text 0 File DVDR.cpp, Line 2534
Start write address at LBA 0
DVD high compatibility mode: Yes
8:28:18 AM #20 Text 0 File Cdrdrv.cpp, Line 8862
---- DVD Structure: Physical Format Information (00h) ----
Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 0.0 (0)
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 26127F h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 0 h
Start sector number of the next Border-In: 0 h
Media Specific [16..63]:
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
8:28:26 AM #21 Text 0 File Cdrdrv.cpp, Line 1286
08:28:26.105 - PLEXTOR DVDR PX-716A\H1 T0 : Queue again later
8:28:40 AM #22 SCSI -500 File Cdrdrv.cpp, Line 1434
SCSI Exec, HA 1, TA 0, LUN 0, buffer 0x038F4A00
Status: 0x02 (0x03, SCSI_ABORTED)
HA-Status 0x10 (0x0A, SCSI_HASTAT_REQUEST_SENSE_FAILED)
TA-Status 0x00 (0x00, OK)
Sense Key: 0x05 (KEY_ILLEGAL_REQUEST)
Sense Code: 0x26
Sense Qual: 0x02
CDB Data: 0x5C 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x0C 0x00 0x00 0x00
Sense Data: 0xF0 0x00 0x05 0x00 0x00 0x00 0x00 0x00
0x00 0x00 0x00 0x00 0x26 0x02
8:28:50 AM #23 SCSI -500 File Cdrdrv.cpp, Line 1434
SCSI Exec, HA 1, TA 0, LUN 0, buffer 0x03FC0000
Status: 0x02 (0x03, SCSI_ABORTED)
HA-Status 0x10 (0x0A, SCSI_HASTAT_REQUEST_SENSE_FAILED)
TA-Status 0x00 (0x00, OK)
Sense Key: 0x05 (KEY_ILLEGAL_REQUEST)
Sense Code: 0x26
Sense Qual: 0x02
CDB Data: 0x2A 0x00 0x00 0x00 0x00 0x20 0x00 0x00 0x20 0x00 0x00 0x00
Sense Data: 0xF0 0x00 0x05 0x00 0x00 0x00 0x00 0x00
0x00 0x00 0x00 0x00 0x26 0x02
8:28:59 AM #24 SCSI -500 File Cdrdrv.cpp, Line 1434
SCSI Exec, HA 1, TA 0, LUN 0, buffer 0x048C0C00
Status: 0x02 (0x03, SCSI_ABORTED)
HA-Status 0x10 (0x0A, SCSI_HASTAT_REQUEST_SENSE_FAILED)
TA-Status 0x00 (0x00, OK)
Sense Key: 0x05 (KEY_ILLEGAL_REQUEST)
Sense Code: 0x26
Sense Qual: 0x02
CDB Data: 0x2A 0x00 0x00 0x00 0x00 0x20 0x00 0x00 0x20 0x00 0x00 0x00
Sense Data: 0xF0 0x00 0x05 0x00 0x00 0x00 0x00 0x00
0x00 0x00 0x00 0x00 0x26 0x02
8:28:59 AM #25 Text 0 File Mmc.cpp, Line 19340
Writer-Buffer for PLEXTOR DVDR PX-716A\H1 T0 reduced to 32768Bytes
8:29:08 AM #26 SCSI -1114 File Cdrdrv.cpp, Line 1434
SCSI Exec, HA 1, TA 0, LUN 0, buffer 0x038F6000
Status: 0x04 (0x01, SCSI_ERR)
HA-Status 0x00 (0x00, OK)
TA-Status 0x02 (0x01, SCSI_TASTATUS_CHKCOND)
Sense Key: 0x06 (KEY_UNIT_ATTENTION)
Sense Code: 0x29
Sense Qual: 0x00
CDB Data: 0x2A 0x00 0x00 0x00 0x00 0x20 0x00 0x00 0x10 0x00 0x00 0x00
Sense Data: 0x70 0x00 0x06 0x00 0x00 0x00 0x00 0x0A
0x00 0x00 0x00 0x00 0x29 0x00
8:29:08 AM #27 CDR -500 File Writer.cpp, Line 311
SCSI command aborted
PLEXTOR DVDR PX-716A\H1 T0
8:29:08 AM #28 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion
8:29:08 AM #29 Text 0 File ThreadedTransfer.cpp, Line 222
conversion idle, stopping reader
8:29:09 AM #30 Text 0 File DVDR.cpp, Line 2774
EndDAO: Last written address was 31
8:29:23 AM #31 Phase 133 File dlgbrnst.cpp, Line 1832
Writing short lead-out
8:29:23 AM #32 CDR -1033 File WriterStatus.cpp, Line 167
Drive not ready
PLEXTOR DVDR PX-716A\H1 T0
8:29:23 AM #33 TRANSFER -24 File WriterStatus.cpp, Line 167
Could not perform end of Disc-at-once
8:29:23 AM #34 Phase 38 File dlgbrnst.cpp, Line 1832
Burn process failed at 8x (11,080 KB/s)
Existing drivers:
File 'Drivers\PXHELP20.SYS': Ver=2.02.62a, size=20016 bytes, created 9/14/2005 2:17:44 PM (Prassi/Veritas driver for win 2K)
File 'Drivers\InCDfs.SYS': Ver=4, 3, 20, 1, size=101504 bytes, created 7/25/2005 10:53:28 AM (InCD4 driver for win NT/2K/XP)
File 'Drivers\InCDpass.SYS': Ver=4, 3, 20, 1, size=29696 bytes, created 7/25/2005 10:53:04 AM (InCD4 driver for win NT/2K/XP)
File 'Drivers\InCDrec.SYS': Ver=4, 3, 20, 1, size=8704 bytes, created 7/25/2005 10:53:30 AM (InCD4 driver for win NT/2K/XP)
Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
|
Moderator
|
19. November 2005 @ 12:09 |
Link to this message
|
@goterps7 -
Quote:
Recorder: <PLEXTOR DVDR PX-716A> Version: 1.03
- firmware's up to date
Quote:
Bus Type : default (0) -> ATAPI, detected: ?
- as your burner is external to the PC that question mark is fine
Quote:
Physical memory : 446MB (457712kB)
Free physical memory: 55MB (56344kB)
Memory in use : 87 %
- free memory is too low, well virtually non-existant, make sure to close down more programs prior to dvd work/burning to free up more memory
Quote:
Recorder: PLEXTOR DVDR PX-716A, Media type: DVD-R
Disc Manufacturer: TYG02 -
Disc Application Code: 64, Disc Physical Code: 193
- are you sure these are genuine TY media ?
Quote:
Writer-Buffer for PLEXTOR DVDR PX-716A\H1 T0 reduced to 32768Bytes
- reduce burn speed
Quote:
Burn process failed at 8x (11,080 KB/s)
- see previous comment, try 4x
Quote:
Existing drivers:
File 'Drivers\InCDfs.SYS': Ver=4, 3, 20, 1, size=101504 bytes, created 7/25/2005 10:53:28 AM (InCD4 driver for win NT/2K/XP)
File 'Drivers\InCDpass.SYS': Ver=4, 3, 20, 1, size=29696 bytes, created 7/25/2005 10:53:04 AM (InCD4 driver for win NT/2K/XP)
File 'Drivers\InCDrec.SYS': Ver=4, 3, 20, 1, size=8704 bytes, created 7/25/2005 10:53:30 AM (InCD4 driver for win NT/2K/XP)
- InCD is Nero's horrid 'packet writing software', uninstall Nero then uninstall completely via Nero's Clean Tools, then reinstall Nero WITHOUT installing InCD
Main PC ~ Intel C2Q Q6600 (G0 Stepping)/Gigabyte GA-EP45-DS3/2GB Crucial Ballistix PC2-8500/Zalman CNPS9700/Antec 900/Corsair HX 620W
Network ~ DD-WRT ~ 2node WDS-WPA2/AES ~ Buffalo WHR-G54S. 3node WPA2/AES ~ WRT54GS v6 (inc. WEP BSSID), WRT54G v2, WRT54G2 v1. *** Forum Rules ***
|
|
goterps7
Junior Member
|
19. November 2005 @ 14:00 |
Link to this message
|
The media is unbranded TY I ordered from mediasupply.com.
I took your advice, but produced a 4th coaster. The memory usage is still really high - I don't understand why because I did this burn right after re-booting. Only automatic programs were running. Any advice on that?
Windows XP 5.1
IA32
WinAspi: -
ahead WinASPI: File 'C:\Program Files\Ahead\nero\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 10/26/2004 6:35:34 PM
Nero Version: 6.6.0.18
Internal Version: 6, 6, 0, 18e
Recorder: <PLEXTOR DVDR PX-716A> Version: 1.03 - HA 1 TA 0 - 6.6.0.18
Adapter driver: <> HA 1
Drive buffer : 8192kB
Bus Type : default (0) -> ATAPI, detected: ?
CD-ROM: <PLEXTOR DVDR PX-716A >Version: 1.03 - HA 1 TA 0 - 6.6.0.18
Adapter driver: <> HA 1
=== Scsi-Device-Map ===
DiskPeripheral : TOSHIBA MK8025GAS atapi Port 0 ID 0 DMA: On
CdRomPeripheral : TEAC DW-224E atapi Port 1 ID 0 DMA: On
=== CDRom-Device-Map ===
PLEXTOR DVDR PX-716A E: CDRom1
=======================
AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 66060288 (0) Byte
ShowDrvBufStat : 0
BUFE : 0
Physical memory : 446MB (457712kB)
Free physical memory: 66MB (67952kB)
Memory in use : 85 %
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)
19.11.2005
ISO compilation
6:53:31 PM #1 Text 0 File Isodoc.cpp, Line 6359
Iso document burn settings
------------------------------------------
Determine maximum speed : FALSE
Simulate : FALSE
Write : TRUE
Finalize CD : TRUE
Multisession : FALSE
Burning mode : DAO
Mode : 1
ISO Level : 1 (Max. of 11 = 8 + 3 char)
Character set : ISO 9660
Joliet : TRUE
Allow pathdepth more than 8 directories : TRUE
Allow more than 255 characters in path : TRUE
Write ISO9660 ;1 file extensions : TRUE
6:53:32 PM #2 Text 0 File Reader.cpp, Line 127
Reader running
6:53:32 PM #3 Text 0 File Writer.cpp, Line 122
Writer PLEXTOR DVDR PX-716A running
6:53:32 PM #4 ISO9660GEN -11 File geniso.cpp, Line 3309
First writeable address = 0 (0x00000000)
6:53:32 PM #5 Text 0 File Burncd.cpp, Line 3233
Turn on Disc-At-Once, using DVD media
6:53:32 PM #6 Text 0 File DlgWaitCD.cpp, Line 270
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 2113807 (469:44.07, 4128MB)
6:53:32 PM #7 Text 0 File DlgWaitCD.cpp, Line 282
Write in overburning mode: NO (enabled: CD)
6:53:32 PM #8 Text 0 File DlgWaitCD.cpp, Line 2483
Recorder: PLEXTOR DVDR PX-716A, Media type: DVD-R
Disc Manufacturer: TYG02 -
Disc Application Code: 64, Disc Physical Code: 193
6:53:32 PM #9 Text 0 File DlgWaitCD.cpp, Line 448
>>> Protocol of DlgWaitCD activities: <<<
=========================================
6:53:32 PM #10 Text 0 File ThreadedTransferInterface.cpp, Line 838
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
2 indices, index0 (150) not provided
original disc pos #0 + 2113808 (2113808) = #2113808/469:44.8
relocatable, disc pos for caching/writing not required/ required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2113808 blocks [PLEXTOR DVDR PX-716A]
--------------------------------------------------------------
6:53:32 PM #11 Text 0 File ThreadedTransferInterface.cpp, Line 1051
Prepare recorder [PLEXTOR DVDR PX-716A] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4329078784, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
2113808 | lead-out | 1 | 0x41 | 0x00
6:53:32 PM #12 Phase 24 File dlgbrnst.cpp, Line 1832
Caching of files started
6:53:33 PM #13 Text 0 File Burncd.cpp, Line 4122
Cache writing successful.
6:53:33 PM #14 Phase 25 File dlgbrnst.cpp, Line 1832
Caching of files completed
6:53:33 PM #15 Phase 36 File dlgbrnst.cpp, Line 1832
Burn process started at 4x (5,540 KB/s)
6:53:33 PM #16 Text 0 File ThreadedTransferInterface.cpp, Line 2661
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0
6:53:33 PM #17 Text 0 File DVDR.cpp, Line 2571
Recording mode: Sequential Recording Mode
6:53:33 PM #18 Text 0 File Mmc.cpp, Line 21774
Set BUFE: BURN-Proof -> ON
6:53:33 PM #19 Text 0 File DVDR.cpp, Line 2726
Start write address at LBA 0
DVD high compatibility mode: Yes
6:53:33 PM #20 Text 0 File Cdrdrv.cpp, Line 8892
---- DVD Structure: Physical Format Information (00h) ----
Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 0.0 (0)
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 26127F h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 0 h
Start sector number of the next Border-In: 0 h
Media Specific [16..63]:
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
6:53:37 PM #21 Text 0 File Cdrdrv.cpp, Line 1288
18:53:37.942 - PLEXTOR DVDR PX-716A\H1 T0 : Queue again later
6:53:38 PM #22 SCSI -500 File Cdrdrv.cpp, Line 1436
SCSI Exec, HA 1, TA 0, LUN 0, buffer 0x038D4A00
Status: 0x02 (0x03, SCSI_ABORTED)
HA-Status 0x10 (0x0A, SCSI_HASTAT_REQUEST_SENSE_FAILED)
TA-Status 0x00 (0x00, OK)
Sense Key: 0x05 (KEY_ILLEGAL_REQUEST)
Sense Code: 0x26
Sense Qual: 0x02
CDB Data: 0x5C 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x0C 0x00 0x00 0x00
Sense Data: 0xF0 0x00 0x05 0x00 0x00 0x00 0x00 0x00
0x00 0x00 0x00 0x00 0x26 0x02
6:53:48 PM #23 SCSI -500 File Cdrdrv.cpp, Line 1436
SCSI Exec, HA 1, TA 0, LUN 0, buffer 0x03F70000
Status: 0x02 (0x03, SCSI_ABORTED)
HA-Status 0x10 (0x0A, SCSI_HASTAT_REQUEST_SENSE_FAILED)
TA-Status 0x00 (0x00, OK)
Sense Key: 0x05 (KEY_ILLEGAL_REQUEST)
Sense Code: 0x26
Sense Qual: 0x02
CDB Data: 0x2A 0x00 0x00 0x00 0x00 0x20 0x00 0x00 0x20 0x00 0x00 0x00
Sense Data: 0xF0 0x00 0x05 0x00 0x00 0x00 0x00 0x00
0x00 0x00 0x00 0x00 0x26 0x02
6:53:57 PM #24 SCSI -500 File Cdrdrv.cpp, Line 1436
SCSI Exec, HA 1, TA 0, LUN 0, buffer 0x047D0A00
Status: 0x02 (0x03, SCSI_ABORTED)
HA-Status 0x10 (0x0A, SCSI_HASTAT_REQUEST_SENSE_FAILED)
TA-Status 0x00 (0x00, OK)
Sense Key: 0x05 (KEY_ILLEGAL_REQUEST)
Sense Code: 0x26
Sense Qual: 0x02
CDB Data: 0x2A 0x00 0x00 0x00 0x00 0x20 0x00 0x00 0x20 0x00 0x00 0x00
Sense Data: 0xF0 0x00 0x05 0x00 0x00 0x00 0x00 0x00
0x00 0x00 0x00 0x00 0x26 0x02
6:53:57 PM #25 Text 0 File Mmc.cpp, Line 19440
Writer-Buffer for PLEXTOR DVDR PX-716A\H1 T0 reduced to 32768Bytes
6:54:06 PM #26 SCSI -500 File Cdrdrv.cpp, Line 1436
SCSI Exec, HA 1, TA 0, LUN 0, buffer 0x038D6000
Status: 0x02 (0x03, SCSI_ABORTED)
HA-Status 0x10 (0x0A, SCSI_HASTAT_REQUEST_SENSE_FAILED)
TA-Status 0x00 (0x00, OK)
Sense Key: 0x05 (KEY_ILLEGAL_REQUEST)
Sense Code: 0x26
Sense Qual: 0x02
CDB Data: 0x2A 0x00 0x00 0x00 0x00 0x20 0x00 0x00 0x10 0x00 0x00 0x00
Sense Data: 0xF0 0x00 0x05 0x00 0x00 0x00 0x00 0x00
0x00 0x00 0x00 0x00 0x26 0x02
6:54:06 PM #27 CDR -500 File Writer.cpp, Line 311
SCSI command aborted
PLEXTOR DVDR PX-716A\H1 T0
6:54:06 PM #28 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion
6:54:06 PM #29 Text 0 File ThreadedTransfer.cpp, Line 222
conversion idle, stopping reader
6:54:06 PM #30 Text 0 File DVDR.cpp, Line 2969
EndDAO: Last written address was 31
6:54:30 PM #31 CDR -1114 File WriterStatus.cpp, Line 167
Reset occurred
PLEXTOR DVDR PX-716A\H1 T0
6:54:30 PM #32 TRANSFER -24 File WriterStatus.cpp, Line 167
Could not perform end of Disc-at-once
6:54:31 PM #33 Phase 38 File dlgbrnst.cpp, Line 1832
Burn process failed at 4x (5,540 KB/s)
Existing drivers:
File 'Drivers\PXHELP20.SYS': Ver=2.02.62a, size=20016 bytes, created 9/14/2005 2:17:44 PM (Prassi/Veritas driver for win 2K)
Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
|
|
goterps7
Junior Member
|
19. November 2005 @ 14:14 |
Link to this message
|
|
Right now, clicked on this page, looking at windows Task Manager -
Physyical Memory (K)
Total 457712
Available 140568
System Cache 198460
Kernal Memory:
Total 59896
Paged 29636
Nonpaged 30260
40 processes are running
|
|
zforum69
Newbie
|
20. November 2005 @ 12:29 |
Link to this message
|
|
|
|
goterps7
Junior Member
|
23. November 2005 @ 23:51 |
Link to this message
|
I waited for Nero's tech support to respond before attempting another burn. They said they thought my firmware wasn't up to date. So I went to Plextor.com and right on the front page, it said there was an update to the firmware for my model as of October 19th. I downloaded it, installed it, rebooted and successfully burned a DVD-R. Is that the final answer, or was there something else that also went right?
Here's the log:
Windows XP 5.1
IA32
WinAspi: -
ahead WinASPI: File 'C:\Program Files\Ahead\nero\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 10/26/2004 6:35:34 PM
Nero Version: 6.6.0.18
Internal Version: 6, 6, 0, 18e
Recorder: <PLEXTOR DVDR PX-716A> Version: 1.09 - HA 1 TA 0 - 6.6.0.18
Adapter driver: <> HA 1
Drive buffer : 8192kB
Bus Type : default (0) -> ATAPI, detected: ?
CD-ROM: <PLEXTOR DVDR PX-716A >Version: 1.09 - HA 1 TA 0 - 6.6.0.18
Adapter driver: <> HA 1
=== Scsi-Device-Map ===
DiskPeripheral : TOSHIBA MK8025GAS atapi Port 0 ID 0 DMA: On
CdRomPeripheral : TEAC DW-224E atapi Port 1 ID 0 DMA: On
=== CDRom-Device-Map ===
PLEXTOR DVDR PX-716A E: CDRom3
=======================
AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 66060288 (0) Byte
ShowDrvBufStat : 0
BUFE : 0
Physical memory : 446MB (457712kB)
Free physical memory: 135MB (139212kB)
Memory in use : 69 %
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)
23.11.2005
ISO compilation
6:44:09 PM #1 Text 0 File Isodoc.cpp, Line 6359
Iso document burn settings
------------------------------------------
Determine maximum speed : FALSE
Simulate : FALSE
Write : TRUE
Finalize CD : FALSE
Multisession : TRUE
Multisession type: : Start multisession
Burning mode : DAO
Mode : 1
ISO Level : 1 (Max. of 11 = 8 + 3 char)
Character set : ISO 9660
Joliet : TRUE
Allow pathdepth more than 8 directories : TRUE
Allow more than 255 characters in path : TRUE
Write ISO9660 ;1 file extensions : TRUE
6:44:09 PM #2 Text 0 File Reader.cpp, Line 127
Reader running
6:44:09 PM #3 Text 0 File Writer.cpp, Line 122
Writer PLEXTOR DVDR PX-716A running
6:44:09 PM #4 ISO9660GEN -11 File geniso.cpp, Line 3309
First writeable address = 0 (0x00000000)
6:44:10 PM #5 Text 0 File Burncd.cpp, Line 3233
Turn on Disc-At-Once, using DVD media
6:44:10 PM #6 Text 0 File DlgWaitCD.cpp, Line 270
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 2113823 (469:44.23, 4128MB)
6:44:10 PM #7 Text 0 File DlgWaitCD.cpp, Line 282
Write in overburning mode: NO (enabled: CD)
6:44:10 PM #8 Text 0 File DlgWaitCD.cpp, Line 2483
Recorder: PLEXTOR DVDR PX-716A, Media type: DVD-R
Disc Manufacturer: TYG02 -
Disc Application Code: 64, Disc Physical Code: 193
6:44:10 PM #9 Text 0 File DlgWaitCD.cpp, Line 448
>>> Protocol of DlgWaitCD activities: <<<
=========================================
6:44:10 PM #10 Text 0 File ThreadedTransferInterface.cpp, Line 838
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
2 indices, index0 (150) not provided
original disc pos #0 + 2113824 (2113824) = #2113824/469:44.24
relocatable, disc pos for caching/writing not required/ required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2113824 blocks [PLEXTOR DVDR PX-716A]
--------------------------------------------------------------
6:44:16 PM #11 Text 0 File ThreadedTransferInterface.cpp, Line 1051
Prepare recorder [PLEXTOR DVDR PX-716A] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc not fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4329111552, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
2113824 | lead-out | 1 | 0x41 | 0x00
6:44:16 PM #12 Phase 24 File dlgbrnst.cpp, Line 1832
Caching of files started
6:44:17 PM #13 Text 0 File Burncd.cpp, Line 4122
Cache writing successful.
6:44:17 PM #14 Phase 25 File dlgbrnst.cpp, Line 1832
Caching of files completed
6:44:17 PM #15 Phase 36 File dlgbrnst.cpp, Line 1832
Burn process started at 4x (5,540 KB/s)
6:44:17 PM #16 Text 0 File ThreadedTransferInterface.cpp, Line 2661
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0
6:44:17 PM #17 Text 0 File DVDR.cpp, Line 2571
Recording mode: Sequential Recording Mode for Multisession
6:44:17 PM #18 Text 0 File Mmc.cpp, Line 21774
Set BUFE: BURN-Proof -> ON
6:44:17 PM #19 Text 0 File DVDR.cpp, Line 2726
Start write address at LBA 0
DVD high compatibility mode: Yes
6:44:17 PM #20 Text 0 File Cdrdrv.cpp, Line 8892
---- DVD Structure: Physical Format Information (00h) ----
Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 0.0 (0)
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 26127F h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 0 h
Start sector number of the next Border-In: 0 h
Media Specific [16..63]:
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
6:44:23 PM #21 Text 0 File Cdrdrv.cpp, Line 1288
18:44:23.655 - PLEXTOR DVDR PX-716A\H1 T0 : Queue again later
6:57:43 PM #22 Text 0 File WriterStatus.cpp, Line 116
<PLEXTOR DVDR PX-716A > start writing Lead-Out at LBA 2113824 (204120h), lenght 0 blocks
6:57:43 PM #23 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion
6:57:43 PM #24 Text 0 File DVDR.cpp, Line 2969
EndDAO: Last written address was 2113823
6:57:49 PM #25 Phase 133 File dlgbrnst.cpp, Line 1832
Writing short lead-out
6:58:36 PM #26 Phase 37 File dlgbrnst.cpp, Line 1832
Burn process completed successfully at 4x (5,540 KB/s)
Existing drivers:
File 'Drivers\PXHELP20.SYS': Ver=2.02.62a, size=20016 bytes, created 9/14/2005 2:17:44 PM (Prassi/Veritas driver for win 2K)
Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
|
|
Advertisement
|
|
|
Moderator
|
24. November 2005 @ 00:33 |
Link to this message
|
@goterps7 -
Quote:
The media is unbranded TY I ordered from mediasupply.com
- i'm not familiar with this website, but to verify if they're genuine TY, one way is to check the HUB codes ie beginning with "GG" or similar, see here for more details - http://forums.afterdawn.com/thread_view.cfm/207196
Quote:
Recorder: <PLEXTOR DVDR PX-716A> Version: 1.09
- well done re the firmware, see here - http://forum.rpc1.org/dl_firmware.php?download_id=1974 - there was indeed a 1.09 version listed there but i misinterpreted the layout of the versions, usually that site separates the groups of firmware to differentiate (for example) 'normal' firmware from 'OEM' firmware.
for example - Quote:
Available Original Firmwares: 1.01, 1.02, 1.03 / 1c04, 1j04 / 1.04, 1.04 (updated), 1.05, 1.06, 1.07, 1.08, 1.09
- i read this to be 3 different variants of firmware. doh!
Quote:
Physical memory : 446MB (457712kB)
Free physical memory: 135MB (139212kB)
Memory in use : 69 %
- free memory could be a little better...
Quote:
Recorder: PLEXTOR DVDR PX-716A, Media type: DVD-R
Disc Manufacturer: TYG02 -
Disc Application Code: 64, Disc Physical Code: 193
- see my first comment re verifying the authenticity of your TY discs
Main PC ~ Intel C2Q Q6600 (G0 Stepping)/Gigabyte GA-EP45-DS3/2GB Crucial Ballistix PC2-8500/Zalman CNPS9700/Antec 900/Corsair HX 620W
Network ~ DD-WRT ~ 2node WDS-WPA2/AES ~ Buffalo WHR-G54S. 3node WPA2/AES ~ WRT54GS v6 (inc. WEP BSSID), WRT54G v2, WRT54G2 v1. *** Forum Rules ***
This message has been edited since posting. Last time this message was edited on 24. November 2005 @ 00:35
|
|
