|
|
|
Nero burning from Hard drive problem
|
|
Newbie
|
25. June 2006 @ 14:20 |
Link to this message
|
burning a movie saved on the computer an it says its burning it but when is done the cd still blank, and there is nothing writen on the disc. I am using Nero 7.0.1.2 Ultra Edition plz help.
The Nero log that I found is as follows:
=== CDRom-Device-Map ===
HP DVD Writer 740b E: CDRom0
=======================
AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 73400320 (0) Byte
BUFE : 0
Physical memory : 503MB (515372kB)
Free physical memory: 132MB (135400kB)
Memory in use : 73
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)
16.6.2006
===== Disc-Copy over image - 1st step : Copy to image ...
9:31:03 AM #1 Text 0 File DlgWaitCD.cpp, Line 301
Write in overburning mode: NO (enabled: CD)
9:31:03 AM #2 Text 0 File DlgWaitCD.cpp, Line 473
>>> Protocol of DlgWaitCD activities: <<<
=========================================
Insert the original disc.
(Medium in drive: Unknown. Medium required by compilation: DVD.)
9:31:04 AM #3 Text 0 File SCSIPassThrough.cpp, Line 39
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME
9:31:04 AM #4 Text 0 File SCSIPassThrough.cpp, Line 84
SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME
9:31:04 AM #5 Text 0 File ThreadedTransfer.cpp, Line 531
ReadBuffer-Pipe got 192KB of Memory
9:31:04 AM #6 Text 0 File Reader.cpp, Line 124
Reader running
9:31:04 AM #7 Text 0 File Writer.cpp, Line 113
Writer Image Recorder running
9:31:04 AM #8 Text 0 File DVDCopy.cpp, Line 292
DVD Track-Information from source disc:
Media Type: DVD-R
S01 T01 Con 0x14 Start 0 Len 2292403 (gap 0) Blank 0 Res 0 Dmg 0 Open Trk 0 Mode TRM_DATA_MODE1 (0)
9:31:04 AM #9 Text 0 File DVDCopy.cpp, Line 405
Max -1 tracks of 1 allowed to copy
1: 0 - 2292403 = 2292403, TRM_DATA_MODE1, block size 2048, read opt 0 (no read options)
9:31:04 AM #10 Text 0 File Burncd.cpp, Line 3365
Turn on Disc-At-Once, using DVD media
9:31:04 AM #11 Text 0 File DlgWaitCD.cpp, Line 289
Last possible write address on media: 4718591 (1048:34.41, 9215MB)
Last address to be written: 2292402 (509:25.27, 4477MB)
9:31:04 AM #12 Text 0 File DlgWaitCD.cpp, Line 301
Write in overburning mode: NO (enabled: CD)
9:31:04 AM #13 Text 0 File DlgWaitCD.cpp, Line 473
>>> Protocol of DlgWaitCD activities: <<<
=========================================
9:31:04 AM #14 Text 0 File ThreadedTransferInterface.cpp, Line 847
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 (1 - Data (mode 1))
2 indices, index0 (150) not provided
original disc pos #0 + 2292403 (2292403) = #2292403/509:25.28
not relocatable, disc pos for caching/writing not required/not required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2292403 blocks [Image Recorder]
--------------------------------------------------------------
9:31:04 AM #15 Text 0 File ThreadedTransferInterface.cpp, Line 1059
Prepare recorder [Image Recorder] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x40; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4694841344, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
2292403 | lead-out | 1 | 0x41 | 0x00
9:31:04 AM #16 Phase 120 File dlgbrnst.cpp, Line 1730
Creating the image for burning
9:31:04 AM #17 Text 0 File ThreadedTransferInterface.cpp, Line 2707
Verifying disc position of item 0 (not relocatable, no disc pos, no patch infos, orig at #0): write at #0
9:40:53 AM #18 Text 0 File WriterStatus.cpp, Line 116
<Image Recorder> start writing Lead-Out at LBA 2292403 (22FAB3h), length 0 blocks
9:40:53 AM #19 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion
9:40:54 AM #20 Phase 121 File dlgbrnst.cpp, Line 1730
Creating Image completed successfully
===== Disc-Copy over image - 2nd step : Burn the image ...
9:41:17 AM #1 Text 0 File ThreadedTransfer.cpp, Line 531
ReadBuffer-Pipe got 262144KB of Memory
9:41:17 AM #2 Text 0 File Reader.cpp, Line 124
Reader running
9:41:17 AM #3 Text 0 File Writer.cpp, Line 113
Writer E: HP DVD Writer 740b running
9:41:22 AM #4 IMAGEGEN -10 File ImageGen.cpp, Line 366
Image was written as DAO.
DAOI:
MediaCatalogNumber = ''
TocType = 0x40
Finalized = 1
First/Last Track = 1 / 1
1: ISRC = ''
Blocksize = 2048
TrackMode = 'TRM_DATA_MODE1'
TrackConfig = 0x00
First/Last Index = 0 / 1
Index0FilePos = 0, Index1FilePos = 0, NextTrackFilePos = 4694841344
CUES:
0: Ctrl=0x41 Trk= 0 (0x00) Index=00 Start=00:00.00 ( 0) RecDep=0x00
1: Ctrl=0x41 Trk= 1 (0x01) Index=00 Start=00:00.00 ( 0) RecDep=0x00
2: Ctrl=0x41 Trk= 1 (0x01) Index=01 Start=00:00.00 ( 0) RecDep=0x00
3: Ctrl=0x41 Trk=110 (0xAA) Index=01 Start=509:25.28 ( 2292403) RecDep=0x00
MTYP: Mediumtype = DVD (old format) (0x1C)
Image file name: <C:\Documents and Settings\HP_Owner\My Documents\TempImage.nrg>
9:41:23 AM #5 Text 0 File Burncd.cpp, Line 3365
Turn on Disc-At-Once, using DVD media
10:03:31 AM #6 Text 0 File DlgWaitCD.cpp, Line 289
Last possible write address on media: 2297903 (510:38.53, 4488MB)
Last address to be written: 2292402 (509:25.27, 4477MB)
10:03:31 AM #7 Text 0 File DlgWaitCD.cpp, Line 301
Write in overburning mode: NO (enabled: CD)
10:03:31 AM #8 Text 0 File DlgWaitCD.cpp, Line 2715
Recorder: HP DVD Writer 740b, Media type: DVD-R
Disc Manufacturer: CMC MA - G. AM3
Disc Application Code: 64, Disc Physical Code: 193
10:03:31 AM #9 Text 0 File DlgWaitCD.cpp, Line 473
>>> Protocol of DlgWaitCD activities: <<<
=========================================
Insert empty disc to write to.
(Medium in drive: Unknown. Medium required by compilation: DVD R/RW, DVD R DL.)
10:03:31 AM #10 Text 0 File ThreadedTransferInterface.cpp, Line 847
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 (1 - DVD-ROM)
2 indices, index0 (150) not provided
original disc pos #0 + 2292403 (2292403) = #2292403/509:25.28
not relocatable, disc pos for caching/writing not required/not required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2292403 blocks [E: HP DVD Writer 740b]
--------------------------------------------------------------
10:03:31 AM #11 Text 0 File ThreadedTransferInterface.cpp, Line 1059
Prepare recorder [E: HP DVD Writer 740b] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x40; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4694841344, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
2292403 | lead-out | 1 | 0x41 | 0x00
10:03:31 AM #12 Text 0 File SCSIPassThrough.cpp, Line 39
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME
10:03:31 AM #13 Text 0 File SCSIPassThrough.cpp, Line 84
SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME
10:03:31 AM #14 Phase 36 File dlgbrnst.cpp, Line 1730
Burn process started at 16x (22,160 KB/s)
10:03:31 AM #15 Text 0 File ThreadedTransferInterface.cpp, Line 2707
Verifying disc position of item 0 (not relocatable, no disc pos, no patch infos, orig at #0): write at #0
10:03:31 AM #16 Text 0 File DVDR.cpp, Line 2786
Recording mode: Sequential Recording Mode
10:03:31 AM #17 Text 0 File DVDR.cpp, Line 2942
Start write address at LBA 0
DVD high compatibility mode: Yes
10:03:31 AM #18 Text 0 File Cdrdrv.cpp, Line 8914
---- DVD Structure: Physical Format Information (00h) ----
Media Type: 0, Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 2.1 (33)
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 26127F h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 2FE10 h
Start sector number of the next Border-In: 2FFA0 h
Media Specific [16..63]:
00 60 00 10 20 30 40 50 - 00 00 00 21 00 00 00 00 .`...0@P...!....
00 02 FE 10 00 02 FF A0 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
10:08:44 AM #19 SPTI -1093 File SCSIPassThrough.cpp, Line 290
E: CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1093)
Sense Key: 0x03 (KEY_MEDIUM_ERROR)
Sense Code: 0x02
Sense Qual: 0x00
CDB Data: 0x2A 00 00 1E 24 E0 00 00 20 00 00 00
Sense Area: 0x70 00 03 00 00 00 00 0E 00 00 00 00 02
Buffer x044d0000: Len x10000
0x00 00 01 BA 45 BF BC 16 DD 01 01 89 C3 F8 00 00
0x01 E0 07 EC 81 00 00 55 AB DD 38 6B 0C DB E4 49
0xA8 68 C5 65 94 3E 27 83 74 1D CD D8 8B 64 02 19
10:08:44 AM #20 CDR -1093 File Writer.cpp, Line 302
No seek complete
E: HP DVD Writer 740b
10:08:45 AM #21 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion
10:08:45 AM #22 Text 0 File ThreadedTransfer.cpp, Line 222
conversion idle, stopping reader
10:08:45 AM #23 Text 0 File DVDR.cpp, Line 3182
EndDAO: Last written address was 1975519
10:08:45 AM #24 Phase 38 File dlgbrnst.cpp, Line 1730
Burn process failed at 16x (22,160 KB/s)
Existing drivers:
File 'Drivers\PXHELP20.SYS': Ver=2.03.32a, size=20640 bytes, created 4/25/2005 6:03:00 PM (Prassi/Veritas driver for win 2K)
Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
====== *** Nero Burning ROM, History File *** ======
Carlos
Ramos family
1C83-7613-10E5-477X-4022-6KM5-4KC2
Windows XP 5.1
IA32
WinAspi: -
ahead WinASPI: File 'C:\Program Files\Nero\Nero 7\Core\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 11/2/2004 1:54:32 PM
NT-SPTI used
Nero Version: 7.2.0.3
Internal Version: 7, 2, 0, 3
Recorder: <HP DVD Writer 740b> Version: ED24 - HA 1 TA 0 - 7.2.0.3
Adapter driver: <IDE> HA 1
Drive buffer : 2048kB
Bus Type : default (0) -> ATAPI, detected: ?
CD-ROM: <HP DVD Writer 740b >Version: ED24 - HA 1 TA 0 - 7.2.0.3
Adapter driver: <IDE> HA 1
=== Scsi-Device-Map ===
CdRomPeripheral : HP DVD Writer 740b atapi Port 0 ID 0 DMA: On
DiskPeripheral : ST3200822AS atapi Port 1 ID 0 DMA: On
=== CDRom-Device-Map ===
HP DVD Writer 740b E: CDRom0
=======================
AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 73400320 (0) Byte
BUFE : 0
Physical memory : 503MB (515372kB)
Free physical memory: 37MB (38196kB)
Memory in use : 92
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)
16.6.2006
===== Disc-Copy over image - 1st step : Copy to image ...
10:11:32 AM #1 Text 0 File DlgWaitCD.cpp, Line 301
Write in overburning mode: NO (enabled: CD)
10:11:32 AM #2 Text 0 File DlgWaitCD.cpp, Line 473
>>> Protocol of DlgWaitCD activities: <<<
=========================================
Insert the original disc.
(Medium in drive: Unknown. Medium required by compilation: DVD.)
10:11:33 AM #3 Text 0 File SCSIPassThrough.cpp, Line 39
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME
10:11:33 AM #4 Text 0 File SCSIPassThrough.cpp, Line 84
SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME
10:11:33 AM #5 Text 0 File ThreadedTransfer.cpp, Line 531
ReadBuffer-Pipe got 192KB of Memory
10:11:33 AM #6 Text 0 File Reader.cpp, Line 124
Reader running
10:11:33 AM #7 Text 0 File Writer.cpp, Line 113
Writer Image Recorder running
10:11:33 AM #8 Text 0 File DVDCopy.cpp, Line 292
DVD Track-Information from source disc:
Media Type: DVD-R
S01 T01 Con 0x14 Start 0 Len 2233728 (gap 0) Blank 0 Res 0 Dmg 0 Open Trk 0 Mode TRM_DATA_MODE1 (0)
10:11:33 AM #9 Text 0 File DVDCopy.cpp, Line 405
Max -1 tracks of 1 allowed to copy
1: 0 - 2233728 = 2233728, TRM_DATA_MODE1, block size 2048, read opt 0 (no read options)
10:11:33 AM #10 Text 0 File Burncd.cpp, Line 3365
Turn on Disc-At-Once, using DVD media
10:11:33 AM #11 Text 0 File DlgWaitCD.cpp, Line 289
Last possible write address on media: 4718591 (1048:34.41, 9215MB)
Last address to be written: 2233727 (496:23.02, 4362MB)
10:11:33 AM #12 Text 0 File DlgWaitCD.cpp, Line 301
Write in overburning mode: NO (enabled: CD)
10:11:33 AM #13 Text 0 File DlgWaitCD.cpp, Line 473
>>> Protocol of DlgWaitCD activities: <<<
=========================================
10:11:33 AM #14 Text 0 File ThreadedTransferInterface.cpp, Line 847
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 (1 - Data (mode 1))
2 indices, index0 (150) not provided
original disc pos #0 + 2233728 (2233728) = #2233728/496:23.3
not relocatable, disc pos for caching/writing not required/not required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2233728 blocks [Image Recorder]
--------------------------------------------------------------
10:11:33 AM #15 Text 0 File ThreadedTransferInterface.cpp, Line 1059
Prepare recorder [Image Recorder] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x40; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4574674944, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
2233728 | lead-out | 1 | 0x41 | 0x00
10:11:33 AM #16 Phase 120 File dlgbrnst.cpp, Line 1730
Creating the image for burning
10:11:34 AM #17 Text 0 File ThreadedTransferInterface.cpp, Line 2707
Verifying disc position of item 0 (not relocatable, no disc pos, no patch infos, orig at #0): write at #0
10:21:22 AM #18 Text 0 File WriterStatus.cpp, Line 116
<Image Recorder> start writing Lead-Out at LBA 2233728 (221580h), length 0 blocks
10:21:22 AM #19 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion
10:21:23 AM #20 Phase 121 File dlgbrnst.cpp, Line 1730
Creating Image completed successfully
===== Disc-Copy over image - 2nd step : Burn the image ...
10:21:43 AM #1 Text 0 File ThreadedTransfer.cpp, Line 531
ReadBuffer-Pipe got 262144KB of Memory
10:21:43 AM #2 Text 0 File Reader.cpp, Line 124
Reader running
10:21:43 AM #3 Text 0 File Writer.cpp, Line 113
Writer E: HP DVD Writer 740b running
10:21:43 AM #4 IMAGEGEN -10 File ImageGen.cpp, Line 366
Image was written as DAO.
DAOI:
MediaCatalogNumber = ''
TocType = 0x40
Finalized = 1
First/Last Track = 1 / 1
1: ISRC = ''
Blocksize = 2048
TrackMode = 'TRM_DATA_MODE1'
TrackConfig = 0x00
First/Last Index = 0 / 1
Index0FilePos = 0, Index1FilePos = 0, NextTrackFilePos = 4574674944
CUES:
0: Ctrl=0x41 Trk= 0 (0x00) Index=00 Start=00:00.00 ( 0) RecDep=0x00
1: Ctrl=0x41 Trk= 1 (0x01) Index=00 Start=00:00.00 ( 0) RecDep=0x00
2: Ctrl=0x41 Trk= 1 (0x01) Index=01 Start=00:00.00 ( 0) RecDep=0x00
3: Ctrl=0x41 Trk=110 (0xAA) Index=01 Start=496:23.03 ( 2233728) RecDep=0x00
MTYP: Mediumtype = DVD (old format) (0x1C)
Image file name: <C:\Documents and Settings\HP_Owner\My Documents\TempImage.nrg>
10:21:45 AM #5 Text 0 File Burncd.cpp, Line 3365
Turn on Disc-At-Once, using DVD media
10:23:20 AM #6 Text 0 File DlgWaitCD.cpp, Line 289
Last possible write address on media: 2297903 (510:38.53, 4488MB)
Last address to be written: 2233727 (496:23.02, 4362MB)
10:23:20 AM #7 Text 0 File DlgWaitCD.cpp, Line 301
Write in overburning mode: NO (enabled: CD)
10:23:20 AM #8 Text 0 File DlgWaitCD.cpp, Line 2715
Recorder: HP DVD Writer 740b, Media type: DVD-R
Disc Manufacturer: CMC MA - G. AM3
Disc Application Code: 64, Disc Physical Code: 193
10:23:20 AM #9 Text 0 File DlgWaitCD.cpp, Line 473
>>> Protocol of DlgWaitCD activities: <<<
=========================================
Insert empty disc to write to.
(Medium in drive: Unknown. Medium required by compilation: DVD R/RW, DVD R DL.)
10:23:20 AM #10 Text 0 File ThreadedTransferInterface.cpp, Line 847
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 (1 - DVD-ROM)
2 indices, index0 (150) not provided
original disc pos #0 + 2233728 (2233728) = #2233728/496:23.3
not relocatable, disc pos for caching/writing not required/not required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2233728 blocks [E: HP DVD Writer 740b]
--------------------------------------------------------------
10:23:20 AM #11 Text 0 File ThreadedTransferInterface.cpp, Line 1059
Prepare recorder [E: HP DVD Writer 740b] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x40; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4574674944, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
2233728 | lead-out | 1 | 0x41 | 0x00
10:23:20 AM #12 Text 0 File SCSIPassThrough.cpp, Line 39
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME
10:23:20 AM #13 Text 0 File SCSIPassThrough.cpp, Line 84
SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME
10:23:20 AM #14 Phase 28 File dlgbrnst.cpp, Line 1730
Speed measurement started
10:23:20 AM #15 Text 0 File ThreadedTransferInterface.cpp, Line 2707
Verifying disc position of item 0 (not relocatable, no disc pos, no patch infos, orig at #0): write at #0
10:25:28 AM #16 Text 0 File WriterStatus.cpp, Line 116
<E: HP DVD Writer 740b> start writing Lead-Out at LBA 2233728 (221580h), length 0 blocks
10:25:28 AM #17 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion
10:25:28 AM #18 Phase 29 File dlgbrnst.cpp, Line 1679
Speed measurement completed: 26.5x (36,684 KB/s)
10:25:28 AM #19 Phase 36 File dlgbrnst.cpp, Line 1730
Burn process started at 2x (2,770 KB/s)
10:25:28 AM #20 Text 0 File ThreadedTransferInterface.cpp, Line 2707
Verifying disc position of item 0 (not relocatable, no disc pos, no patch infos, orig at #0): write at #0
10:25:28 AM #21 Text 0 File DVDR.cpp, Line 2786
Recording mode: Sequential Recording Mode
10:25:28 AM #22 Text 0 File DVDR.cpp, Line 2942
Start write address at LBA 0
DVD high compatibility mode: Yes
10:25:28 AM #23 Text 0 File Cdrdrv.cpp, Line 8914
---- DVD Structure: Physical Format Information (00h) ----
Media Type: 0, Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 2.1 (33)
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 26127F h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 2FE10 h
Start sector number of the next Border-In: 2FFA0 h
Media Specific [16..63]:
00 60 00 10 20 30 40 50 - 00 00 00 21 00 00 00 00 .`...0@P...!....
00 02 FE 10 00 02 FF A0 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
10:53:12 AM #24 Text 0 File WriterStatus.cpp, Line 116
<E: HP DVD Writer 740b> start writing Lead-Out at LBA 2233728 (221580h), length 0 blocks
10:53:12 AM #25 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion
10:53:13 AM #26 Text 0 File DVDR.cpp, Line 3182
EndDAO: Last written address was 2233727
10:54:07 AM #27 Phase 37 File dlgbrnst.cpp, Line 1730
Burn process completed successfully at 2x (2,770 KB/s)
Existing drivers:
File 'Drivers\PXHELP20.SYS': Ver=2.03.32a, size=20640 bytes, created 4/25/2005 6:03:00 PM (Prassi/Veritas driver for win 2K)
Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
====== *** Nero Burning ROM, History File *** ======
Carlos
Ramos family
1C83-7613-10E5-477X-4022-6KM5-4KC2
Windows XP 5.1
IA32
WinAspi: -
ahead WinASPI: File 'C:\Program Files\Nero\Nero 7\Core\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 11/2/2004 1:54:32 PM
NT-SPTI used
Nero Version: 7.2.0.3
Internal Version: 7, 2, 0, 3
Recorder: < Image Recorder> Version: Not available - HA -1 TA 0 - 7.2.0.3
Adapter driver: <Virtual Device> HA -1
Drive buffer :
CD-ROM: <HP DVD Writer 740b >Version: ED24 - HA 1 TA 0 - 7.2.0.3
Adapter driver: <IDE> HA 1
=== Scsi-Device-Map ===
CdRomPeripheral : HP DVD Writer 740b atapi Port 0 ID 0 DMA: On
DiskPeripheral : ST3200822AS atapi Port 1 ID 0 DMA: On
=== CDRom-Device-Map ===
HP DVD Writer 740b E: CDRom0
=======================
AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 73400320 (0) Byte
BUFE : 0
Physical memory : 503MB (515372kB)
Free physical memory: 285MB (291976kB)
Memory in use : 43
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)
16.6.2006
DVD-Copy over Image
10:58:55 AM #1 Text 0 File DlgWaitCD.cpp, Line 301
Write in overburning mode: NO (enabled: CD)
10:58:55 AM #2 Text 0 File DlgWaitCD.cpp, Line 473
>>> Protocol of DlgWaitCD activities: <<<
=========================================
Insert the original disc.
(Medium in drive: Unknown. Medium required by compilation: DVD.)
10:58:56 AM #3 Text 0 File SCSIPassThrough.cpp, Line 39
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME
10:58:56 AM #4 Text 0 File SCSIPassThrough.cpp, Line 84
SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME
10:58:56 AM #5 Text 0 File ThreadedTransfer.cpp, Line 531
ReadBuffer-Pipe got 192KB of Memory
10:58:56 AM #6 Text 0 File Reader.cpp, Line 124
Reader running
10:58:57 AM #7 Text 0 File DVDCopy.cpp, Line 292
DVD Track-Information from source disc:
Media Type: DVD-ROM
Last LBA on layer 0 = 2044143 / 0x1F30EF / 3992MB
S01 T01 Con 0x14 Start 0 Len 4080085 (gap 0) Blank 0 Res 0 Dmg 0 Open Trk 0 Mode TRM_DATA_MODE1 (0)
10:58:57 AM #8 CDCOPY -33 File DVDCopy.cpp, Line 342
This DVD is copy-protected and cannot be read
Existing drivers:
File 'Drivers\PXHELP20.SYS': Ver=2.03.32a, size=20640 bytes, created 4/25/2005 6:03:00 PM (Prassi/Veritas driver for win 2K)
Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
====== *** Nero Burning ROM, History File *** ======
Carlos
Ramos family
1C83-7613-10E5-477X-4022-6KM5-4KC2
Windows XP 5.1
IA32
WinAspi: -
ahead WinASPI: File 'C:\Program Files\Nero\Nero 7\Core\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 11/2/2004 1:54:32 PM
NT-SPTI used
Nero Version: 7.2.0.3
Internal Version: 7, 2, 0, 3
Recorder: < Image Recorder> Version: Not available - HA -1 TA 0 - 7.2.0.3
Adapter driver: <Virtual Device> HA -1
Drive buffer :
CD-ROM: <HP DVD Writer 740b >Version: ED24 - HA 1 TA 0 - 7.2.0.3
Adapter driver: <IDE> HA 1
=== Scsi-Device-Map ===
CdRomPeripheral : HP DVD Writer 740b atapi Port 0 ID 0 DMA: On
DiskPeripheral : ST3200822AS atapi Port 1 ID 0 DMA: On
=== CDRom-Device-Map ===
HP DVD Writer 740b E: CDRom0
=======================
AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 73400320 (0) Byte
BUFE : 0
Physical memory : 503MB (515372kB)
Free physical memory: 252MB (258512kB)
Memory in use : 49
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)
16.6.2006
DVD-Copy over Image
11:06:55 AM #1 Text 0 File SCSIPassThrough.cpp, Line 39
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME
11:06:55 AM #2 Text 0 File SCSIPassThrough.cpp, Line 84
SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME
11:06:55 AM #3 Text 0 File ThreadedTransfer.cpp, Line 531
ReadBuffer-Pipe got 192KB of Memory
11:06:55 AM #4 Text 0 File Reader.cpp, Line 124
Reader running
11:06:55 AM #5 Text 0 File DVDCopy.cpp, Line 292
DVD Track-Information from source disc:
Media Type: DVD-ROM
Last LBA on layer 0 = 2069535 / 0x1F941F / 4042MB
S01 T01 Con 0x14 Start 0 Len 4138446 (gap 0) Blank 0 Res 0 Dmg 0 Open Trk 0 Mode TRM_DATA_MODE1 (0)
11:06:55 AM #6 CDCOPY -33 File DVDCopy.cpp, Line 342
This DVD is copy-protected and cannot be read
Existing drivers:
File 'Drivers\PXHELP20.SYS': Ver=2.03.32a, size=20640 bytes, created 4/25/2005 6:03:00 PM (Prassi/Veritas driver for win 2K)
Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
====== *** Nero Burning ROM, History File *** ======
Carlos
Ramos family
1C83-7613-10E5-477X-4022-6KM5-4KC2
Windows XP 5.1
IA32
WinAspi: -
ahead WinASPI: File 'C:\Program Files\Nero\Nero 7\Core\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 11/2/2004 1:54:32 PM
NT-SPTI used
Nero Version: 7.2.0.3
Internal Version: 7, 2, 0, 3
Recorder: < Image Recorder> Version: Not available - HA -1 TA 0 - 7.2.0.3
Adapter driver: <Virtual Device> HA -1
Drive buffer :
CD-ROM: <HP DVD Writer 740b >Version: ED24 - HA 1 TA 0 - 7.2.0.3
Adapter driver: <IDE> HA 1
=== Scsi-Device-Map ===
CdRomPeripheral : HP DVD Writer 740b atapi Port 0 ID 0 DMA: On
DiskPeripheral : ST3200822AS atapi Port 1 ID 0 DMA: On
=== CDRom-Device-Map ===
HP DVD Writer 740b E: CDRom0
=======================
AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 73400320 (0) Byte
BUFE : 0
Physical memory : 503MB (515372kB)
Free physical memory: 213MB (218256kB)
Memory in use : 57
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)
16.6.2006
DVD-Copy over Image
11:18:33 AM #1 Text 0 File SCSIPassThrough.cpp, Line 39
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME
11:18:33 AM #2 Text 0 File SCSIPassThrough.cpp, Line 84
SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME
11:18:33 AM #3 Text 0 File ThreadedTransfer.cpp, Line 531
ReadBuffer-Pipe got 192KB of Memory
11:18:33 AM #4 Text 0 File Reader.cpp, Line 124
Reader running
11:18:33 AM #5 Text 0 File DVDCopy.cpp, Line 292
DVD Track-Information from source disc:
Media Type: DVD-ROM
Last LBA on layer 0 = 2069535 / 0x1F941F / 4042MB
S01 T01 Con 0x14 Start 0 Len 4138446 (gap 0) Blank 0 Res 0 Dmg 0 Open Trk 0 Mode TRM_DATA_MODE1 (0)
11:18:33 AM #6 CDCOPY -33 File DVDCopy.cpp, Line 342
This DVD is copy-protected and cannot be read
Existing drivers:
File 'Drivers\PXHELP20.SYS': Ver=2.03.32a, size=20640 bytes, created 4/25/2005 6:03:00 PM (Prassi/Veritas driver for win 2K)
Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
====== *** Nero Burning ROM, History File *** ======
Carlos
Ramos family
1C83-7613-10E5-477X-4022-6KM5-4KC2
Windows XP 5.1
IA32
WinAspi: -
ahead WinASPI: File 'C:\Program Files\Nero\Nero 7\Core\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 11/2/2004 1:54:32 PM
NT-SPTI used
Nero Version: 7.2.0.3
Internal Version: 7, 2, 0, 3
Recorder: <HP DVD Writer 740b> Version: ED24 - HA 1 TA 0 - 7.2.0.3
Adapter driver: <IDE> HA 1
Drive buffer : 2048kB
Bus Type : default (0) -> ATAPI, detected: ?
CD-ROM: <HP DVD Writer 740b >Version: ED24 - HA 1 TA 0 - 7.2.0.3
Adapter driver: <IDE> HA 1
=== Scsi-Device-Map ===
CdRomPeripheral : HP DVD Writer 740b atapi Port 0 ID 0 DMA: On
DiskPeripheral : ST3200822AS atapi Port 1 ID 0 DMA: On
=== CDRom-Device-Map ===
HP DVD Writer 740b E: CDRom0
=======================
AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 73400320 (0) Byte
BUFE : 0
Physical memory : 503MB (515372kB)
Free physical memory: 87MB (89476kB)
Memory in use : 82
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)
16.6.2006
===== Disc-Copy over image - 1st step : Copy to image ...
11:23:23 AM #1 SPTI -1033 File SCSIPassThrough.cpp, Line 290
E: CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1033)
Sense Key: 0x02 (KEY_NOT_READY)
Sense Code: 0x04
Sense Qual: 0x01
CDB Data: 0x00 00 00 00 00 00 00 00 00 00 00 00
Sense Area: 0x70 00 02 00 00 00 00 0E 00 00 00 00 04 01
11:23:45 AM #2 SPTI -1066 File SCSIPassThrough.cpp, Line 290
E: CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1066)
Sense Key: 0x05 (KEY_ILLEGAL_REQUEST)
Sense Code: 0x24
Sense Qual: 0x00
CDB Data: 0xAC 00 00 00 00 00 00 00 01 00 00 00
Sense Area: 0x70 00 05 00 00 00 00 0E 00 00 00 00 24
Buffer x0351c800: Len x1008
11:23:50 AM #3 Text 0 File SCSIPassThrough.cpp, Line 39
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME
11:23:50 AM #4 Text 0 File SCSIPassThrough.cpp, Line 84
SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME
11:23:50 AM #5 Text 0 File ThreadedTransfer.cpp, Line 531
ReadBuffer-Pipe got 192KB of Memory
11:23:50 AM #6 Text 0 File Reader.cpp, Line 124
Reader running
11:23:50 AM #7 Text 0 File Writer.cpp, Line 113
Writer Image Recorder running
11:23:50 AM #8 Text 0 File DVDCopy.cpp, Line 292
DVD Track-Information from source disc:
Media Type: DVD-R
S01 T01 Con 0x14 Start 0 Len 2292403 (gap 0) Blank 0 Res 0 Dmg 0 Open Trk 0 Mode TRM_DATA_MODE1 (0)
11:23:50 AM #9 Text 0 File DVDCopy.cpp, Line 405
Max -1 tracks of 1 allowed to copy
1: 0 - 2292403 = 2292403, TRM_DATA_MODE1, block size 2048, read opt 0 (no read options)
11:23:50 AM #10 Text 0 File Burncd.cpp, Line 3365
Turn on Disc-At-Once, using DVD media
11:23:50 AM #11 Text 0 File DlgWaitCD.cpp, Line 289
Last possible write address on media: 4718591 (1048:34.41, 9215MB)
Last address to be written: 2292402 (509:25.27, 4477MB)
11:23:50 AM #12 Text 0 File DlgWaitCD.cpp, Line 301
Write in overburning mode: NO (enabled: CD)
11:23:50 AM #13 Text 0 File DlgWaitCD.cpp, Line 473
>>> Protocol of DlgWaitCD activities: <<<
=========================================
11:23:50 AM #14 Text 0 File ThreadedTransferInterface.cpp, Line 847
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 (1 - Data (mode 1))
2 indices, index0 (150) not provided
original disc pos #0 + 2292403 (2292403) = #2292403/509:25.28
not relocatable, disc pos for caching/writing not required/not required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2292403 blocks [Image Recorder]
--------------------------------------------------------------
11:23:50 AM #15 Text 0 File ThreadedTransferInterface.cpp, Line 1059
Prepare recorder [Image Recorder] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x40; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4694841344, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
2292403 | lead-out | 1 | 0x41 | 0x00
11:23:50 AM #16 Phase 120 File dlgbrnst.cpp, Line 1730
Creating the image for burning
11:23:50 AM #17 Text 0 File ThreadedTransferInterface.cpp, Line 2707
Verifying disc position of item 0 (not relocatable, no disc pos, no patch infos, orig at #0): write at #0
11:36:49 AM #18 Text 0 File WriterStatus.cpp, Line 116
<Image Recorder> start writing Lead-Out at LBA 2292403 (22FAB3h), length 0 blocks
11:36:49 AM #19 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion
11:36:51 AM #20 Phase 121 File dlgbrnst.cpp, Line 1730
Creating Image completed successfully
===== Disc-Copy over image - 2nd step : Burn the image ...
11:37:14 AM #1 Text 0 File ThreadedTransfer.cpp, Line 531
ReadBuffer-Pipe got 262144KB of Memory
11:37:14 AM #2 Text 0 File Reader.cpp, Line 124
Reader running
11:37:14 AM #3 Text 0 File Writer.cpp, Line 113
Writer E: HP DVD Writer 740b running
11:37:17 AM #4 IMAGEGEN -10 File ImageGen.cpp, Line 366
Image was written as DAO.
DAOI:
MediaCatalogNumber = ''
TocType = 0x40
Finalized = 1
First/Last Track = 1 / 1
1: ISRC = ''
Blocksize = 2048
TrackMode = 'TRM_DATA_MODE1'
TrackConfig = 0x00
First/Last Index = 0 / 1
Index0FilePos = 0, Index1FilePos = 0, NextTrackFilePos = 4694841344
CUES:
0: Ctrl=0x41 Trk= 0 (0x00) Index=00 Start=00:00.00 ( 0) RecDep=0x00
1: Ctrl=0x41 Trk= 1 (0x01) Index=00 Start=00:00.00 ( 0) RecDep=0x00
2: Ctrl=0x41 Trk= 1 (0x01) Index=01 Start=00:00.00 ( 0) RecDep=0x00
3: Ctrl=0x41 Trk=110 (0xAA) Index=01 Start=509:25.28 ( 2292403) RecDep=0x00
MTYP: Mediumtype = DVD (old format) (0x1C)
Image file name: <C:\Documents and Settings\HP_Owner\My Documents\TempImage.nrg>
11:37:18 AM #5 Text 0 File Burncd.cpp, Line 3365
Turn on Disc-At-Once, using DVD media
11:37:50 AM #6 Text 0 File DlgWaitCD.cpp, Line 289
Last possible write address on media: 2297903 (510:38.53, 4488MB)
Last address to be written: 2292402 (509:25.27, 4477MB)
11:37:50 AM #7 Text 0 File DlgWaitCD.cpp, Line 301
Write in overburning mode: NO (enabled: CD)
11:37:50 AM #8 Text 0 File DlgWaitCD.cpp, Line 2715
Recorder: HP DVD Writer 740b, Media type: DVD-R
Disc Manufacturer: CMC MA - G. AM3
Disc Application Code: 64, Disc Physical Code: 193
11:37:50 AM #9 Text 0 File DlgWaitCD.cpp, Line 473
>>> Protocol of DlgWaitCD activities: <<<
=========================================
Insert empty disc to write to.
(Medium in drive: Unknown. Medium required by compilation: DVD R/RW, DVD R DL.)
11:37:50 AM #10 Text 0 File ThreadedTransferInterface.cpp, Line 847
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 (1 - DVD-ROM)
2 indices, index0 (150) not provided
original disc pos #0 + 2292403 (2292403) = #2292403/509:25.28
not relocatable, disc pos for caching/writing not required/not required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2292403 blocks [E: HP DVD Writer 740b]
--------------------------------------------------------------
11:37:50 AM #11 Text 0 File ThreadedTransferInterface.cpp, Line 1059
Prepare recorder [E: HP DVD Writer 740b] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x40; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4694841344, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
2292403 | lead-out | 1 | 0x41 | 0x00
11:37:50 AM #12 Text 0 File SCSIPassThrough.cpp, Line 39
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME
11:37:50 AM #13 Text 0 File SCSIPassThrough.cpp, Line 84
SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME
11:37:50 AM #14 Phase 28 File dlgbrnst.cpp, Line 1730
Speed measurement started
11:37:50 AM #15 Text 0 File ThreadedTransferInterface.cpp, Line 2707
Verifying disc position of item 0 (not relocatable, no disc pos, no patch infos, orig at #0): write at #0
11:41:03 AM #16 Text 0 File WriterStatus.cpp, Line 116
<E: HP DVD Writer 740b> start writing Lead-Out at LBA 2292403 (22FAB3h), length 0 blocks
11:41:03 AM #17 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion
11:41:03 AM #18 Phase 29 File dlgbrnst.cpp, Line 1679
Speed measurement completed: 18x (24,894 KB/s)
11:41:03 AM #19 Phase 36 File dlgbrnst.cpp, Line 1730
Burn process started at 16x (22,160 KB/s)
11:41:03 AM #20 Text 0 File ThreadedTransferInterface.cpp, Line 2707
Verifying disc position of item 0 (not relocatable, no disc pos, no patch infos, orig at #0): write at #0
11:41:03 AM #21 Text 0 File DVDR.cpp, Line 2786
Recording mode: Sequential Recording Mode
11:41:03 AM #22 Text 0 File DVDR.cpp, Line 2942
Start write address at LBA 0
DVD high compatibility mode: Yes
11:41:03 AM #23 Text 0 File Cdrdrv.cpp, Line 8914
---- DVD Structure: Physical Format Information (00h) ----
Media Type: 0, Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 2.1 (33)
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 26127F h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 2FE10 h
Start sector number of the next Border-In: 2FFA0 h
Media Specific [16..63]:
00 60 00 10 20 30 40 50 - 00 00 00 21 00 00 00 00 .`...0@P...!....
00 02 FE 10 00 02 FF A0 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
11:46:11 AM #24 SPTI -1093 File SCSIPassThrough.cpp, Line 290
E: CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1093)
Sense Key: 0x03 (KEY_MEDIUM_ERROR)
Sense Code: 0x02
Sense Qual: 0x00
CDB Data: 0x2A 00 00 1E 69 20 00 00 20 00 00 00
Sense Area: 0x70 00 03 00 00 00 00 0E 00 00 00 00 02
Buffer x044c0000: Len x10000
0x00 00 01 BA 45 C3 96 24 94 AB 01 89 C3 F8 00 00
0x01 E0 07 EC 81 00 00 CB F7 04 CA B6 6C 1E 5C DA
0x57 B6 E8 10 9B 91 B8 BA 5E B6 B2 38 1F 7A D7 76
11:46:11 AM #25 CDR -1093 File Writer.cpp, Line 302
No seek complete
E: HP DVD Writer 740b
11:46:11 AM #26 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion
11:46:12 AM #27 Text 0 File ThreadedTransfer.cpp, Line 222
conversion idle, stopping reader
11:46:12 AM #28 Text 0 File DVDR.cpp, Line 3182
EndDAO: Last written address was 1992991
11:46:12 AM #29 Phase 38 File dlgbrnst.cpp, Line 1730
Burn process failed at 16x (22,160 KB/s)
Existing drivers:
File 'Drivers\PXHELP20.SYS': Ver=2.03.32a, size=20640 bytes, created 4/25/2005 6:03:00 PM (Prassi/Veritas driver for win 2K)
Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
====== *** Nero Burning ROM, History File *** ======
1C83-7613-10E5-477X-4022-6KM5-4KC2
Windows XP 5.1
IA32
WinAspi: -
ahead WinASPI: File 'C:\Program Files\Nero\Nero 7\Core\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 11/2/2004 1:54:32 PM
NT-SPTI used
Nero API version: 7.2.0.3
Using interface version: 7.0.5.6
Installed in: C:\Program Files\Nero\Nero 7\Core\
Application: ahead\NeroVision
Internal Version: 7, 2, 0, 3
Recorder: <HP DVD Writer 740b> Version: ED24 - HA 1 TA 0 - 7.2.0.3
Adapter driver: <IDE> HA 1
Drive buffer : 2048kB
Bus Type : default (0) -> ATAPI, detected: ?
=== Scsi-Device-Map ===
CdRomPeripheral : HP DVD Writer 740b atapi Port 0 ID 0 DMA: On
DiskPeripheral : ST3200822AS atapi Port 1 ID 0 DMA: On
=== CDRom-Device-Map ===
HP DVD Writer 740b E: CDRom0
=======================
AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 73400320 (0) Byte
BUFE : 0
Physical memory : 503MB (515372kB)
Free physical memory: 71MB (73288kB)
Memory in use : 85
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)
19.6.2006
NeroAPI
12:17:50 AM #1 Phase 111 File APIProgress.cpp, Line 278
DVD-Video files sorted
12:17:51 AM #2 Text 0 File ThreadedTransfer.cpp, Line 531
ReadBuffer-Pipe got 262144KB of Memory
12:17:51 AM #3 Text 0 File Reader.cpp, Line 124
Reader running
12:17:51 AM #4 Text 0 File Writer.cpp, Line 113
Writer E: HP DVD Writer 740b running
12:17:51 AM #5 ISO9660GEN -11 File Geniso.cpp, Line 3312
First writeable address = 0 (0x00000000)
12:17:51 AM #6 ISO9660GEN -11 File Geniso.cpp, Line 3312
First writeable address = 0 (0x00000000)
12:17:51 AM #7 Text 0 File Burncd.cpp, Line 3365
Turn on Disc-At-Once, using DVD media
12:17:52 AM #8 Text 0 File DlgWaitCD.cpp, Line 289
Last possible write address on media: 2297903 (510:38.53, 4488MB)
Last address to be written: 1761407 (391:25.32, 3440MB)
12:17:52 AM #9 Text 0 File DlgWaitCD.cpp, Line 301
Write in overburning mode: NO (enabled: CD)
12:17:52 AM #10 Text 0 File DlgWaitCD.cpp, Line 2715
Recorder: HP DVD Writer 740b, Media type: DVD-R
Disc Manufacturer: CMC MA - G. AM3
Disc Application Code: 64, Disc Physical Code: 193
12:17:52 AM #11 Text 0 File DlgWaitCD.cpp, Line 473
>>> Protocol of DlgWaitCD activities: <<<
=========================================
12:17:52 AM #12 Text 0 File ThreadedTransferInterface.cpp, Line 847
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
2 indices, index0 (150) not provided
original disc pos #0 + 1761408 (1761408) = #1761408/391:25.33
relocatable, disc pos for caching/writing not required/ required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 1761408 blocks [E: HP DVD Writer 740b]
--------------------------------------------------------------
12:17:52 AM #13 Text 0 File ThreadedTransferInterface.cpp, Line 1059
Prepare recorder [E: HP DVD Writer 740b] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 3607363584, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
1761408 | lead-out | 1 | 0x41 | 0x00
12:17:52 AM #14 Text 0 File SCSIPassThrough.cpp, Line 39
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME
12:17:52 AM #15 Text 0 File SCSIPassThrough.cpp, Line 84
SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME
12:17:52 AM #16 Phase 24 File APIProgress.cpp, Line 278
Caching of files started
12:17:52 AM #17 Text 0 File Burncd.cpp, Line 4199
Cache writing successful.
12:17:52 AM #18 Phase 25 File APIProgress.cpp, Line 278
Caching of files completed
12:17:52 AM #19 Phase 36 File APIProgress.cpp, Line 278
Burn process started at 16x (22,160 KB/s)
12:17:52 AM #20 Text 0 File ThreadedTransferInterface.cpp, Line 2707
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0
12:17:52 AM #21 Text 0 File DVDR.cpp, Line 2786
Recording mode: Sequential Recording Mode
12:17:52 AM #22 Text 0 File DVDR.cpp, Line 2942
Start write address at LBA 0
DVD high compatibility mode: Yes
12:17:52 AM #23 Text 0 File Cdrdrv.cpp, Line 8914
---- DVD Structure: Physical Format Information (00h) ----
Media Type: 0, Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 2.1 (33)
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 26127F h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 2FE10 h
Start sector number of the next Border-In: 2FFA0 h
Media Specific [16..63]:
00 60 00 10 20 30 40 50 - 00 00 00 21 00 00 00 00 .`...0@P...!....
00 02 FE 10 00 02 FF A0 - 00 00 00 00 00 00 00 00 ..þ...ÿ.........
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
12:24:28 AM #24 Text 0 File WriterStatus.cpp, Line 116
<E: HP DVD Writer 740b> start writing Lead-Out at LBA 1761408 (1AE080h), length 0 blocks
12:24:28 AM #25 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion
12:24:28 AM #26 Text 0 File DVDR.cpp, Line 3182
EndDAO: Last written address was 1761407
12:24:51 AM #27 Phase 37 File APIProgress.cpp, Line 278
Burn process completed successfully at 16x (22,160 KB/s)
Existing drivers:
File 'Drivers\PXHELP20.SYS': Ver=2.03.32a, size=20640 bytes, created 4/25/2005 6:03:00 PM (Prassi/Veritas driver for win 2K)
Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
====== *** NeroAPI, History File *** ======
Carlos
Ramos family
1C83-7613-10E5-477X-4022-6KM5-4KC2
Windows XP 5.1
IA32
WinAspi: -
ahead WinASPI: File 'C:\Program Files\Nero\Nero 7\Core\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 11/2/2004 1:54:32 PM
NT-SPTI used
Nero Version: 7.2.0.3
Internal Version: 7, 2, 0, 3
Recorder: <HP DVD Writer 740b> Version: ED24 - HA 1 TA 0 - 7.2.0.3
Adapter driver: <IDE> HA 1
Drive buffer : 2048kB
Bus Type : default (0) -> ATAPI, detected: ?
CD-ROM: <HP DVD Writer 740b >Version: ED24 - HA 1 TA 0 - 7.2.0.3
Adapter driver: <IDE> HA 1
=== Scsi-Device-Map ===
CdRomPeripheral : HP DVD Writer 740b atapi Port 0 ID 0 DMA: On
DiskPeripheral : ST3200822AS atapi Port 1 ID 0 DMA: On
=== CDRom-Device-Map ===
HP DVD Writer 740b E: CDRom0
=======================
AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 73400320 (0) Byte
BUFE : 0
Physical memory : 503MB (515372kB)
Free physical memory: 44MB (45876kB)
Memory in use : 91
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)
19.6.2006
===== Disc-Copy over image - 1st step : Copy to image ...
1:31:56 AM #1 Text 0 File SCSIPassThrough.cpp, Line 39
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME
1:31:56 AM #2 Text 0 File SCSIPassThrough.cpp, Line 84
SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME
1:31:56 AM #3 Text 0 File ThreadedTransfer.cpp, Line 531
ReadBuffer-Pipe got 192KB of Memory
1:31:56 AM #4 Text 0 File Reader.cpp, Line 124
Reader running
1:31:56 AM #5 Text 0 File Writer.cpp, Line 113
Writer Image Recorder running
1:31:56 AM #6 Text 0 File DVDCopy.cpp, Line 292
DVD Track-Information from source disc:
Media Type: DVD-ROM
S01 T01 Con 0x14 Start 0 Len 1689232 (gap 0) Blank 0 Res 0 Dmg 0 Open Trk 0 Mode TRM_DATA_MODE1 (0)
1:31:56 AM #7 Text 0 File DVDCopy.cpp, Line 405
Max -1 tracks of 1 allowed to copy
1: 0 - 1689232 = 1689232, TRM_DATA_MODE1, block size 2048, read opt 0 (no read options)
1:31:56 AM #8 Text 0 File Burncd.cpp, Line 3365
Turn on Disc-At-Once, using DVD media
1:31:57 AM #9 Text 0 File DlgWaitCD.cpp, Line 289
Last possible write address on media: 4718591 (1048:34.41, 9215MB)
Last address to be written: 1689231 (375:23.06, 3299MB)
1:31:57 AM #10 Text 0 File DlgWaitCD.cpp, Line 301
Write in overburning mode: NO (enabled: CD)
1:31:57 AM #11 Text 0 File DlgWaitCD.cpp, Line 473
>>> Protocol of DlgWaitCD activities: <<<
=========================================
1:31:57 AM #12 Text 0 File ThreadedTransferInterface.cpp, Line 847
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 (1 - Data (mode 1))
2 indices, index0 (150) not provided
original disc pos #0 + 1689232 (1689232) = #1689232/375:23.7
not relocatable, disc pos for caching/writing not required/not required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 1689232 blocks [Image Recorder]
--------------------------------------------------------------
1:31:57 AM #13 Text 0 File ThreadedTransferInterface.cpp, Line 1059
Prepare recorder [Image Recorder] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x40; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 3459547136, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
1689232 | lead-out | 1 | 0x41 | 0x00
1:31:57 AM #14 Phase 120 File dlgbrnst.cpp, Line 1730
Creating the image for burning
1:31:57 AM #15 Text 0 File ThreadedTransferInterface.cpp, Line 2707
Verifying disc position of item 0 (not relocatable, no disc pos, no patch infos, orig at #0): write at #0
1:39:48 AM #16 Text 0 File WriterStatus.cpp, Line 116
<Image Recorder> start writing Lead-Out at LBA 1689232 (19C690h), length 0 blocks
1:39:48 AM #17 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion
1:39:49 AM #18 Phase 121 File dlgbrnst.cpp, Line 1730
Creating Image completed successfully
===== Disc-Copy over image - 2nd step : Burn the image ...
1:40:33 AM #1 Text 0 File ThreadedTransfer.cpp, Line 531
ReadBuffer-Pipe got 262144KB of Memory
1:40:33 AM #2 Text 0 File Reader.cpp, Line 124
Reader running
1:40:33 AM #3 Text 0 File Writer.cpp, Line 113
Writer E: HP DVD Writer 740b running
1:40:34 AM #4 IMAGEGEN -10 File ImageGen.cpp, Line 366
Image was written as DAO.
DAOI:
MediaCatalogNumber = ''
TocType = 0x40
Finalized = 1
First/Last Track = 1 / 1
1: ISRC = ''
Blocksize = 2048
TrackMode = 'TRM_DATA_MODE1'
TrackConfig = 0x00
First/Last Index = 0 / 1
Index0FilePos = 0, Index1FilePos = 0, NextTrackFilePos = 3459547136
CUES:
0: Ctrl=0x41 Trk= 0 (0x00) Index=00 Start=00:00.00 ( 0) RecDep=0x00
1: Ctrl=0x41 Trk= 1 (0x01) Index=00 Start=00:00.00 ( 0) RecDep=0x00
2: Ctrl=0x41 Trk= 1 (0x01) Index=01 Start=00:00.00 ( 0) RecDep=0x00
3: Ctrl=0x41 Trk=110 (0xAA) Index=01 Start=375:23.07 ( 1689232) RecDep=0x00
MTYP: Mediumtype = DVD (old format) (0x1C)
Image file name: <C:\Documents and Settings\HP_Owner\My Documents\TempImage.nrg>
1:40:35 AM #5 Text 0 File Burncd.cpp, Line 3365
Turn on Disc-At-Once, using DVD media
1:41:32 AM #6 Text 0 File DlgWaitCD.cpp, Line 289
Last possible write address on media: 2297903 (510:38.53, 4488MB)
Last address to be written: 1689231 (375:23.06, 3299MB)
1:41:32 AM #7 Text 0 File DlgWaitCD.cpp, Line 301
Write in overburning mode: NO (enabled: CD)
1:41:32 AM #8 Text 0 File DlgWaitCD.cpp, Line 2715
Recorder: HP DVD Writer 740b, Media type: DVD-R
Disc Manufacturer: CMC MA - G. AM3
Disc Application Code: 64, Disc Physical Code: 193
1:41:32 AM #9 Text 0 File DlgWaitCD.cpp, Line 473
>>> Protocol of DlgWaitCD activities: <<<
=========================================
Insert empty disc to write to.
(Medium in drive: Unknown. Medium required by compilation: DVD R/RW, DVD R DL.)
1:41:32 AM #10 Text 0 File ThreadedTransferInterface.cpp, Line 847
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 (1 - DVD-ROM)
2 indices, index0 (150) not provided
original disc pos #0 + 1689232 (1689232) = #1689232/375:23.7
not relocatable, disc pos for caching/writing not required/not required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 1689232 blocks [E: HP DVD Writer 740b]
--------------------------------------------------------------
1:41:32 AM #11 Text 0 File ThreadedTransferInterface.cpp, Line 1059
Prepare recorder [E: HP DVD Writer 740b] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x40; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 3459547136, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
1689232 | lead-out | 1 | 0x41 | 0x00
1:41:32 AM #12 Text 0 File SCSIPassThrough.cpp, Line 39
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME
1:41:32 AM #13 Text 0 File SCSIPassThrough.cpp, Line 84
SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME
1:41:32 AM #14 Phase 36 File dlgbrnst.cpp, Line 1730
Burn process started at 16x (22,160 KB/s)
1:41:32 AM #15 Text 0 File ThreadedTransferInterface.cpp, Line 2707
Verifying disc position of item 0 (not relocatable, no disc pos, no patch infos, orig at #0): write at #0
1:41:32 AM #16 Text 0 File DVDR.cpp, Line 2786
Recording mode: Sequential Recording Mode
1:41:32 AM #17 Text 0 File DVDR.cpp, Line 2942
Start write address at LBA 0
DVD high compatibility mode: Yes
1:41:32 AM #18 Text 0 File Cdrdrv.cpp, Line 8914
---- DVD Structure: Physical Format Information (00h) ----
Media Type: 0, Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 2.1 (33)
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 26127F h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 2FE10 h
Start sector number of the next Border-In: 2FFA0 h
Media Specific [16..63]:
00 60 00 10 20 30 40 50 - 00 00 00 21 00 00 00 00 .`...0@P...!....
00 02 FE 10 00 02 FF A0 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
1:49:23 AM #19 Text 0 File WriterStatus.cpp, Line 116
<E: HP DVD Writer 740b> start writing Lead-Out at LBA 1689232 (19C690h), length 0 blocks
1:49:23 AM #20 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion
1:49:24 AM #21 Text 0 File DVDR.cpp, Line 3182
EndDAO: Last written address was 1689231
1:49:52 AM #22 Phase 37 File dlgbrnst.cpp, Line 1730
Burn process completed successfully at 16x (22,160 KB/s)
Existing drivers:
File 'Drivers\PXHELP20.SYS': Ver=2.03.32a, size=20640 bytes, created 4/25/2005 6:03:00 PM (Prassi/Veritas driver for win 2K)
Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
====== *** Nero Burning ROM, History File *** ======
Carlos
Ramos family
1C83-7613-10E5-477X-4022-6KM5-4KC2
Windows XP 5.1
IA32
WinAspi: -
ahead WinASPI: File 'C:\Program Files\Nero\Nero 7\Core\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 11/2/2004 1:54:32 PM
NT-SPTI used
Nero Version: 7.2.0.3
Internal Version: 7, 2, 0, 3
Recorder: <HP DVD Writer 740b> Version: ED24 - HA 1 TA 0 - 7.2.0.3
Adapter driver: <IDE> HA 1
Drive buffer : 2048kB
Bus Type : default (0) -> ATAPI, detected: ?
CD-ROM: <HP DVD Writer 740b >Version: ED24 - HA 1 TA 0 - 7.2.0.3
Adapter driver: <IDE> HA 1
=== Scsi-Device-Map ===
CdRomPeripheral : HP DVD Writer 740b atapi Port 0 ID 0 DMA: On
DiskPeripheral : ST3200822AS atapi Port 1 ID 0 DMA: On
=== CDRom-Device-Map ===
HP DVD Writer 740b E: CDRom0
=======================
AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 73400320 (0) Byte
BUFE : 0
Physical memory : 503MB (515372kB)
Free physical memory: 119MB (122440kB)
Memory in use : 76
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)
19.6.2006
===== Disc-Copy over image - 1st step : Copy to image ...
2:24:42 AM #1 SPTI -1033 File SCSIPassThrough.cpp, Line 290
E: CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1033)
Sense Key: 0x02 (KEY_NOT_READY)
Sense Code: 0x04
Sense Qual: 0x01
CDB Data: 0x00 00 00 00 00 00 00 00 00 00 00 00
Sense Area: 0x70 00 02 00 00 00 00 0E 00 00 00 00 04 01
2:24:58 AM #2 Text 0 File SCSIPassThrough.cpp, Line 39
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME
2:24:58 AM #3 Text 0 File SCSIPassThrough.cpp, Line 84
SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME
2:24:58 AM #4 Text 0 File ThreadedTransfer.cpp, Line 531
ReadBuffer-Pipe got 192KB of Memory
2:24:58 AM #5 Text 0 File Reader.cpp, Line 124
Reader running
2:24:58 AM #6 Text 0 File Writer.cpp, Line 113
Writer Image Recorder running
2:24:58 AM #7 Text 0 File DVDCopy.cpp, Line 292
DVD Track-Information from source disc:
Media Type: DVD-ROM
S01 T01 Con 0x14 Start 0 Len 1667872 (gap 0) Blank 0 Res 0 Dmg 0 Open Trk 0 Mode TRM_DATA_MODE1 (0)
2:24:58 AM #8 Text 0 File DVDCopy.cpp, Line 405
Max -1 tracks of 1 allowed to copy
1: 0 - 1667872 = 1667872, TRM_DATA_MODE1, block size 2048, read opt 0 (no read options)
2:24:58 AM #9 Text 0 File Burncd.cpp, Line 3365
Turn on Disc-At-Once, using DVD media
2:24:59 AM #10 Text 0 File DlgWaitCD.cpp, Line 289
Last possible write address on media: 4718591 (1048:34.41, 9215MB)
Last address to be written: 1667871 (370:38.21, 3257MB)
2:24:59 AM #11 Text 0 File DlgWaitCD.cpp, Line 301
Write in overburning mode: NO (enabled: CD)
2:24:59 AM #12 Text 0 File DlgWaitCD.cpp, Line 473
>>> Protocol of DlgWaitCD activities: <<<
=========================================
2:24:59 AM #13 Text 0 File ThreadedTransferInterface.cpp, Line 847
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 (1 - Data (mode 1))
2 indices, index0 (150) not provided
original disc pos #0 + 1667872 (1667872) = #1667872/370:38.22
not relocatable, disc pos for caching/writing not required/not required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 1667872 blocks [Image Recorder]
--------------------------------------------------------------
2:24:59 AM #14 Text 0 File ThreadedTransferInterface.cpp, Line 1059
Prepare recorder [Image Recorder] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x40; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 3415801856, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
1667872 | lead-out | 1 | 0x41 | 0x00
2:24:59 AM #15 Phase 120 File dlgbrnst.cpp, Line 1730
Creating the image for burning
2:24:59 AM #16 Text 0 File ThreadedTransferInterface.cpp, Line 2707
Verifying disc position of item 0 (not relocatable, no disc pos, no patch infos, orig at #0): write at #0
2:35:39 AM #17 Text 0 File WriterStatus.cpp, Line 116
<Image Recorder> start writing Lead-Out at LBA 1667872 (197320h), length 0 blocks
2:35:39 AM #18 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion
2:35:44 AM #19 Phase 121 File dlgbrnst.cpp, Line 1730
Creating Image completed successfully
===== Disc-Copy over image - 2nd step : Burn the image ...
2:36:06 AM #1 Text 0 File ThreadedTransfer.cpp, Line 531
ReadBuffer-Pipe got 262144KB of Memory
2:36:06 AM #2 Text 0 File Reader.cpp, Line 124
Reader running
2:36:06 AM #3 Text 0 File Writer.cpp, Line 113
Writer E: HP DVD Writer 740b running
2:36:07 AM #4 IMAGEGEN -10 File ImageGen.cpp, Line 366
Image was written as DAO.
DAOI:
MediaCatalogNumber = ''
TocType = 0x40
Finalized = 1
First/Last Track = 1 / 1
1: ISRC = ''
Blocksize = 2048
TrackMode = 'TRM_DATA_MODE1'
TrackConfig = 0x00
First/Last Index = 0 / 1
Index0FilePos = 0, Index1FilePos = 0, NextTrackFilePos = 3415801856
CUES:
0: Ctrl=0x41 Trk= 0 (0x00) Index=00 Start=00:00.00 ( 0) RecDep=0x00
1: Ctrl=0x41 Trk= 1 (0x01) Index=00 Start=00:00.00 ( 0) RecDep=0x00
2: Ctrl=0x41 Trk= 1 (0x01) Index=01 Start=00:00.00 ( 0) RecDep=0x00
3: Ctrl=0x41 Trk=110 (0xAA) Index=01 Start=370:38.22 ( 1667872) RecDep=0x00
MTYP: Mediumtype = DVD (old format) (0x1C)
Image file name: <C:\Documents and Settings\HP_Owner\My Documents\TempImage.nrg>
2:36:08 AM #5 Text 0 File Burncd.cpp, Line 3365
Turn on Disc-At-Once, using DVD media
8:36:06 AM #6 Text 0 File DlgWaitCD.cpp, Line 289
Last possible write address on media: 2297903 (510:38.53, 4488MB)
Last address to be written: 1667871 (370:38.21, 3257MB)
8:36:06 AM #7 Text 0 File DlgWaitCD.cpp, Line 301
Write in overburning mode: NO (enabled: CD)
8:36:06 AM #8 Text 0 File DlgWaitCD.cpp, Line 2715
Recorder: HP DVD Writer 740b, Media type: DVD-R
Disc Manufacturer: CMC MA - G. AM3
Disc Application Code: 64, Disc Physical Code: 193
8:36:06 AM #9 Text 0 File DlgWaitCD.cpp, Line 473
>>> Protocol of DlgWaitCD activities: <<<
=========================================
Insert empty disc to write to.
(Medium in drive: Unknown. Medium required by compilation: DVD R/RW, DVD R DL.)
8:36:06 AM #10 Text 0 File ThreadedTransferInterface.cpp, Line 847
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 (1 - DVD-ROM)
2 indices, index0 (150) not provided
original disc pos #0 + 1667872 (1667872) = #1667872/370:38.22
not relocatable, disc pos for caching/writing not required/not required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 1667872 blocks [E: HP DVD Writer 740b]
--------------------------------------------------------------
8:36:06 AM #11 Text 0 File ThreadedTransferInterface.cpp, Line 1059
Prepare recorder [E: HP DVD Writer 740b] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x40; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 3415801856, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
1667872 | lead-out | 1 | 0x41 | 0x00
8:36:06 AM #12 Text 0 File SCSIPassThrough.cpp, Line 39
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME
8:36:06 AM #13 Text 0 File SCSIPassThrough.cpp, Line 84
SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME
8:36:06 AM #14 Phase 36 File dlgbrnst.cpp, Line 1730
Burn process started at 16x (22,160 KB/s)
8:36:06 AM #15 Text 0 File ThreadedTransferInterface.cpp, Line 2707
Verifying disc position of item 0 (not relocatable, no disc pos, no patch infos, orig at #0): write at #0
8:36:06 AM #16 Text 0 File DVDR.cpp, Line 2786
Recording mode: Sequential Recording Mode
8:36:06 AM #17 Text 0 File DVDR.cpp, Line 2942
Start write address at LBA 0
DVD high compatibility mode: Yes
8:36:06 AM #18 Text 0 File Cdrdrv.cpp, Line 8914
---- DVD Structure: Physical Format Information (00h) ----
Media Type: 0, Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 2.1 (33)
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 26127F h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 2FE10 h
Start sector number of the next Border-In: 2FFA0 h
Media Specific [16..63]:
00 60 00 10 20 30 40 50 - 00 00 00 21 00 00 00 00 .`...0@P...!....
00 02 FE 10 00 02 FF A0 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
8:48:53 AM #19 Text 0 File WriterStatus.cpp, Line 116
<E: HP DVD Writer 740b> start writing Lead-Out at LBA 1667872 (197320h), length 0 blocks
8:48:54 AM #20 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion
8:48:54 AM #21 Text 0 File DVDR.cpp, Line 3182
EndDAO: Last written address was 1667871
8:49:18 AM #22 Phase 37 File dlgbrnst.cpp, Line 1730
Burn process completed successfully at 16x (22,160 KB/s)
Existing drivers:
File 'Drivers\PXHELP20.SYS': Ver=2.03.32a, size=20640 bytes, created 4/25/2005 6:03:00 PM (Prassi/Veritas driver for win 2K)
Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
====== *** Nero Burning ROM, History File *** ======
Carlos
Ramos family
1C83-7613-10E5-477X-4022-6KM5-4KC2
Windows XP 5.1
IA32
WinAspi: -
ahead WinASPI: File 'C:\Program Files\Nero\Nero 7\Core\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 11/2/2004 1:54:32 PM
NT-SPTI used
Nero Version: 7.2.0.3
Internal Version: 7, 2, 0, 3
Recorder: <HP DVD Writer 740b> Version: ED24 - HA 1 TA 0 - 7.2.0.3
Adapter driver: <IDE> HA 1
Drive buffer : 2048kB
Bus Type : default (0) -> ATAPI, detected: ?
CD-ROM: <HP DVD Writer 740b >Version: ED24 - HA 1 TA 0 - 7.2.0.3
Adapter driver: <IDE> HA 1
=== Scsi-Device-Map ===
CdRomPeripheral : HP DVD Writer 740b atapi Port 0 ID 0 DMA: On
DiskPeripheral : ST3200822AS atapi Port 1 ID 0 DMA: On
=== CDRom-Device-Map ===
HP DVD Writer 740b E: CDRom0
=======================
AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 73400320 (0) Byte
BUFE : 0
Physical memory : 503MB (515372kB)
Free physical memory: 86MB (88592kB)
Memory in use : 82
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)
19.6.2006
===== Disc-Copy over image - 1st step : Copy to image ...
8:59:44 AM #1 Text 0 File DlgWaitCD.cpp, Line 301
Write in overburning mode: NO (enabled: CD)
8:59:44 AM #2 Text 0 File DlgWaitCD.cpp, Line 473
>>> Protocol of DlgWaitCD activities: <<<
=========================================
Insert the original disc.
(Medium in drive: Unknown. Medium required by compilation: DVD.)
8:59:45 AM #3 Text 0 File SCSIPassThrough.cpp, Line 39
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME
8:59:45 AM #4 Text 0 File SCSIPassThrough.cpp, Line 84
SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME
8:59:45 AM #5 Text 0 File ThreadedTransfer.cpp, Line 531
ReadBuffer-Pipe got 192KB of Memory
8:59:45 AM #6 Text 0 File Reader.cpp, Line 124
Reader running
8:59:45 AM #7 Text 0 File Writer.cpp, Line 113
Writer Image Recorder running
8:59:45 AM #8 Text 0 File DVDCopy.cpp, Line 292
DVD Track-Information from source disc:
Media Type: DVD+R
S01 T01 Con 0x14 Start 0 Len 1601232 (gap 0) Blank 0 Res 0 Dmg 0 Open Trk 0 Mode TRM_DATA_MODE1 (0)
8:59:45 AM #9 Text 0 File DVDCopy.cpp, Line 405
Max -1 tracks of 1 allowed to copy
1: 0 - 1601232 = 1601232, TRM_DATA_MODE1, block size 2048, read opt 0 (no read options)
8:59:45 AM #10 Text 0 File Burncd.cpp, Line 3365
Turn on Disc-At-Once, using DVD media
8:59:45 AM #11 Text 0 File DlgWaitCD.cpp, Line 289
Last possible write address on media: 4718591 (1048:34.41, 9215MB)
Last address to be written: 1601231 (355:49.56, 3127MB)
8:59:45 AM #12 Text 0 File DlgWaitCD.cpp, Line 301
Write in overburning mode: NO (enabled: CD)
8:59:45 AM #13 Text 0 File DlgWaitCD.cpp, Line 473
>>> Protocol of DlgWaitCD activities: <<<
=========================================
8:59:45 AM #14 Text 0 File ThreadedTransferInterface.cpp, Line 847
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 (1 - Data (mode 1))
2 indices, index0 (150) not provided
original disc pos #0 + 1601232 (1601232) = #1601232/355:49.57
not relocatable, disc pos for caching/writing not required/not required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 1601232 blocks [Image Recorder]
--------------------------------------------------------------
8:59:45 AM #15 Text 0 File ThreadedTransferInterface.cpp, Line 1059
Prepare recorder [Image Recorder] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x40; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 3279323136, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
1601232 | lead-out | 1 | 0x41 | 0x00
8:59:45 AM #16 Phase 120 File dlgbrnst.cpp, Line 1730
Creating the image for burning
8:59:45 AM #17 Text 0 File ThreadedTransferInterface.cpp, Line 2707
Verifying disc position of item 0 (not relocatable, no disc pos, no patch infos, orig at #0): write at #0
9:09:59 AM #18 Text 0 File WriterStatus.cpp, Line 116
<Image Recorder> start writing Lead-Out at LBA 1601232 (186ED0h), length 0 blocks
9:09:59 AM #19 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion
9:09:59 AM #20 Phase 121 File dlgbrnst.cpp, Line 1730
Creating Image completed successfully
===== Disc-Copy over image - 2nd step : Burn the image ...
9:10:18 AM #1 Text 0 File ThreadedTransfer.cpp, Line 531
ReadBuffer-Pipe got 262144KB of Memory
9:10:18 AM #2 Text 0 File Reader.cpp, Line 124
Reader running
9:10:18 AM #3 Text 0 File Writer.cpp, Line 113
Writer E: HP DVD Writer 740b running
9:10:22 AM #4 IMAGEGEN -10 File ImageGen.cpp, Line 366
Image was written as DAO.
DAOI:
MediaCatalogNumber = ''
TocType = 0x40
Finalized = 1
First/Last Track = 1 / 1
1: ISRC = ''
Blocksize = 2048
TrackMode = 'TRM_DATA_MODE1'
TrackConfig = 0x00
First/Last Index = 0 / 1
Index0FilePos = 0, Index1FilePos = 0, NextTrackFilePos = 3279323136
CUES:
0: Ctrl=0x41 Trk= 0 (0x00) Index=00 Start=00:00.00 ( 0) RecDep=0x00
1: Ctrl=0x41 Trk= 1 (0x01) Index=00 Start=00:00.00 ( 0) RecDep=0x00
2: Ctrl=0x41 Trk= 1 (0x01) Index=01 Start=00:00.00 ( 0) RecDep=0x00
3: Ctrl=0x41 Trk=110 (0xAA) Index=01 Start=355:49.57 ( 1601232) RecDep=0x00
MTYP: Mediumtype = DVD (old format) (0x1C)
Image file name: <C:\Documents and Settings\HP_Owner\My Documents\TempImage.nrg>
9:10:22 AM #5 Text 0 File Burncd.cpp, Line 3365
Turn on Disc-At-Once, using DVD media
9:21:55 AM #6 Text 0 File DlgWaitCD.cpp, Line 289
Last possible write address on media: 2297903 (510:38.53, 4488MB)
Last address to be written: 1601231 (355:49.56, 3127MB)
9:21:55 AM #7 Text 0 File DlgWaitCD.cpp, Line 301
Write in overburning mode: NO (enabled: CD)
9:21:55 AM #8 Text 0 File DlgWaitCD.cpp, Line 2715
Recorder: HP DVD Writer 740b, Media type: DVD-R
Disc Manufacturer: CMC MA - G. AM3
Disc Application Code: 64, Disc Physical Code: 193
9:21:55 AM #9 Text 0 File DlgWaitCD.cpp, Line 473
>>> Protocol of DlgWaitCD activities: <<<
=========================================
Insert empty disc to write to.
(Medium in drive: Unknown. Medium required by compilation: DVD R/RW, DVD R DL.)
9:21:55 AM #10 Text 0 File ThreadedTransferInterface.cpp, Line 847
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 (1 - DVD-ROM)
2 indices, index0 (150) not provided
original disc pos #0 + 1601232 (1601232) = #1601232/355:49.57
not relocatable, disc pos for caching/writing not required/not required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 1601232 blocks [E: HP DVD Writer 740b]
--------------------------------------------------------------
9:21:55 AM #11 Text 0 File ThreadedTransferInterface.cpp, Line 1059
Prepare recorder [E: HP DVD Writer 740b] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x40; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 3279323136, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
1601232 | lead-out | 1 | 0x41 | 0x00
9:21:55 AM #12 Text 0 File SCSIPassThrough.cpp, Line 39
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME
9:21:55 AM #13 Text 0 File SCSIPassThrough.cpp, Line 84
SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME
9:21:55 AM #14 Phase 36 File dlgbrnst.cpp, Line 1730
Burn process started at 12x (16,620 KB/s)
9:21:55 AM #15 Text 0 File ThreadedTransferInterface.cpp, Line 2707
Verifying disc position of item 0 (not relocatable, no disc pos, no patch infos, orig at #0): write at #0
9:21:55 AM #16 Text 0 File DVDR.cpp, Line 2786
Recording mode: Sequential Recording Mode
9:21:55 AM #17 Text 0 File DVDR.cpp, Line 2942
Start write address at LBA 0
DVD high compatibility mode: Yes
9:21:55 AM #18 Text 0 File Cdrdrv.cpp, Line 8914
---- DVD Structure: Physical Format Information (00h) ----
Media Type: 0, Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 2.1 (33)
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 26127F h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 2FE10 h
Start sector number of the next Border-In: 2FFA0 h
Media Specific [16..63]:
00 60 00 10 20 30 40 50 - 00 00 00 21 00 00 00 00 .`...0@P...!....
00 02 FE 10 00 02 FF A0 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
9:28:04 AM #19 Text 0 File WriterStatus.cpp, Line 116
<E: HP DVD Writer 740b> start writing Lead-Out at LBA 1601232 (186ED0h), length 0 blocks
9:28:04 AM #20 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion
9:28:04 AM #21 Text 0 File DVDR.cpp, Line 3182
EndDAO: Last written address was 1601231
9:28:30 AM #22 Phase 37 File dlgbrnst.cpp, Line 1730
Burn process completed successfully at 12x (16,620 KB/s)
Existing drivers:
File 'Drivers\PXHELP20.SYS': Ver=2.03.32a, size=20640 bytes, created 4/25/2005 6:03:00 PM (Prassi/Veritas driver for win 2K)
Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
====== *** Nero Burning ROM, History File *** ======
5C82-0010-8011-0000-8595-5521-3208
Windows XP 5.1
IA32
WinAspi: -
ahead WinASPI: File 'C:\Program Files\Nero\Nero 7\Core\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 11/2/2004 12:54:32 PM
NT-SPTI used
Nero Version: 7.0.1.2
Internal Version: 7, 0, 1, 2
(Nero Express)
Recorder: <HP DVD Writer 740b> Version: ED24 - HA 1 TA 0 - 7.0.1.2
Adapter driver: <IDE> HA 1
Drive buffer : 2048kB
Bus Type : default (0) -> ATAPI, detected: ?
CD-ROM: <HP DVD Writer 740b >Version: ED24 - HA 1 TA 0 - 7.0.1.2
Adapter driver: <IDE> HA 1
=== Scsi-Device-Map ===
CdRomPeripheral : HP DVD Writer 740b atapi Port 0 ID 0 DMA: On
DiskPeripheral : ST3200822AS atapi Port 1 ID 0 DMA: On
=== CDRom-Device-Map ===
HP DVD Writer 740b E: CDRom0
=======================
AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 73400320 (0) Byte
ShowDrvBufStat : 0
BUFE : 0
Physical memory : 503MB (515372kB)
Free physical memory: 51MB (52840kB)
Memory in use : 89
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)
25.6.2006
===== Disc-Copy over image - 1st step : Copy to image ...
9:20:42 PM #1 Text 0 File SCSIPassThrough.cpp, Line 36
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME
9:20:42 PM #2 Text 0 File ThreadedTransfer.cpp, Line 525
ReadBuffer-Pipe got 192KB of Memory
9:20:42 PM #3 Text 0 File Reader.cpp, Line 124
Reader running
9:20:42 PM #4 Text 0 File Writer.cpp, Line 113
Writer Image Recorder running
9:20:42 PM #5 Text 0 File DVDCopy.cpp, Line 292
DVD Track-Information from source disc:
Media Type: DVD-R
S01 T01 Con 0x14 Start 0 Len 1928672 (gap 0) Blank 0 Res 0 Dmg 0 Open Trk 0 Mode TRM_DATA_MODE1 (0)
9:20:42 PM #6 Text 0 File DVDCopy.cpp, Line 405
Max -1 tracks of 1 allowed to copy
1: 0 - 1928672 = 1928672, TRM_DATA_MODE1, block size 2048, read opt 0 (no read options)
9:20:42 PM #7 Text 0 File Burncd.cpp, Line 3302
Turn on Disc-At-Once, using DVD media
9:20:42 PM #8 Text 0 File DlgWaitCD.cpp, Line 279
Last possible write address on media: 4718591 (1048:34.41, 9215MB)
Last address to be written: 1928671 (428:35.46, 3766MB)
9:20:42 PM #9 Text 0 File DlgWaitCD.cpp, Line 291
Write in overburning mode: NO (enabled: CD)
9:20:42 PM #10 Text 0 File DlgWaitCD.cpp, Line 458
>>> Protocol of DlgWaitCD activities: <<<
=========================================
9:20:42 PM #11 Text 0 File ThreadedTransferInterface.cpp, Line 847
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 (1 - Data (mode 1))
2 indices, index0 (150) not provided
original disc pos #0 + 1928672 (1928672) = #1928672/428:35.47
not relocatable, disc pos for caching/writing not required/not required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 1928672 blocks [Image Recorder]
--------------------------------------------------------------
9:20:42 PM #12 Text 0 File ThreadedTransferInterface.cpp, Line 1059
Prepare recorder [Image Recorder] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x40; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 3949920256, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
1928672 | lead-out | 1 | 0x41 | 0x00
9:20:42 PM #13 Phase 120 File dlgbrnst.cpp, Line 1725
Creating the image for burning
9:20:42 PM #14 Text 0 File ThreadedTransferInterface.cpp, Line 2685
Verifying disc position of item 0 (not relocatable, no disc pos, no patch infos, orig at #0): write at #0
9:32:45 PM #15 Text 0 File WriterStatus.cpp, Line 116
<Image Recorder> start writing Lead-Out at LBA 1928672 (1D6DE0h), length 0 blocks
9:32:45 PM #16 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion
9:32:45 PM #17 Phase 121 File dlgbrnst.cpp, Line 1725
Creating Image completed successfully
===== Disc-Copy over image - 2nd step : Burn the image ...
9:33:22 PM #1 Text 0 File ThreadedTransfer.cpp, Line 525
ReadBuffer-Pipe got 262144KB of Memory
9:33:22 PM #2 Text 0 File Reader.cpp, Line 124
Reader running
9:33:22 PM #3 Text 0 File Writer.cpp, Line 113
Writer E: HP DVD Writer 740b running
9:33:23 PM #4 IMAGEGEN -10 File ImageGen.cpp, Line 366
Image was written as DAO.
DAOI:
MediaCatalogNumber = ''
TocType = 0x40
Finalized = 1
First/Last Track = 1 / 1
1: ISRC = ''
Blocksize = 2048
TrackMode = 'TRM_DATA_MODE1'
TrackConfig = 0x00
First/Last Index = 0 / 1
Index0FilePos = 0, Index1FilePos = 0, NextTrackFilePos = 3949920256
CUES:
0: Ctrl=0x41 Trk= 0 (0x00) Index=00 Start=00:00.00 ( 0) RecDep=0x00
1: Ctrl=0x41 Trk= 1 (0x01) Index=00 Start=00:00.00 ( 0) RecDep=0x00
2: Ctrl=0x41 Trk= 1 (0x01) Index=01 Start=00:00.00 ( 0) RecDep=0x00
3: Ctrl=0x41 Trk=110 (0xAA) Index=01 Start=428:35.47 ( 1928672) RecDep=0x00
MTYP: Mediumtype = DVD (old format) (0x1C)
Image file name: <C:\Documents and Settings\HP_Owner\My Documents\TempImage.nrg>
9:33:25 PM #5 Text 0 File Burncd.cpp, Line 3302
Turn on Disc-At-Once, using DVD media
10:29:38 PM #6 Text 0 File DlgWaitCD.cpp, Line 279
Last possible write address on media: 2297903 (510:38.53, 4488MB)
Last address to be written: 1928671 (428:35.46, 3766MB)
10:29:38 PM #7 Text 0 File DlgWaitCD.cpp, Line 291
Write in overburning mode: NO (enabled: CD)
10:29:38 PM #8 Text 0 File DlgWaitCD.cpp, Line 2578
Recorder: HP DVD Writer 740b, Media type: DVD-R
Disc Manufacturer: CMC MA - G. AM3
Disc Application Code: 64, Disc Physical Code: 193
10:29:38 PM #9 Text 0 File DlgWaitCD.cpp, Line 458
>>> Protocol of DlgWaitCD activities: <<<
=========================================
Insert empty disc to write to.
(Medium in drive: Unknown. Medium required by compilation: DVD+R/RW, DVD-R/RW, DVD-R DL, DVD+R DL.)
10:29:38 PM #10 Text 0 File ThreadedTransferInterface.cpp, Line 847
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 (1 - DVD-ROM)
2 indices, index0 (150) not provided
original disc pos #0 + 1928672 (1928672) = #1928672/428:35.47
not relocatable, disc pos for caching/writing not required/not required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 1928672 blocks [E: HP DVD Writer 740b]
--------------------------------------------------------------
10:29:38 PM #11 Text 0 File ThreadedTransferInterface.cpp, Line 1059
Prepare recorder [E: HP DVD Writer 740b] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x40; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 3949920256, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
1928672 | lead-out | 1 | 0x41 | 0x00
10:29:38 PM #12 Text 0 File SCSIPassThrough.cpp, Line 36
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME
10:29:39 PM #13 Phase 36 File dlgbrnst.cpp, Line 1725
Burn process started at 16x (22,160 KB/s)
10:29:39 PM #14 Text 0 File ThreadedTransferInterface.cpp, Line 2685
Verifying disc position of item 0 (not relocatable, no disc pos, no patch infos, orig at #0): write at #0
10:29:39 PM #15 Text 0 File DVDR.cpp, Line 2580
Recording mode: Sequential Recording Mode
10:29:39 PM #16 Text 0 File MMC.cpp, Line 21611
Set BUFE: Buffer underrun protection -> ON
10:29:39 PM #17 Text 0 File DVDR.cpp, Line 2735
Start write address at LBA 0
DVD high compatibility mode: Yes
10:29:39 PM #18 Text 0 File Cdrdrv.cpp, Line 8411
---- DVD Structure: Physical Format Information (00h) ----
Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 2.1 (33)
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 26127F h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 2FE10 h
Start sector number of the next Border-In: 2FFA0 h
Media Specific [16..63]:
00 60 00 10 20 30 40 50 - 00 00 00 21 00 00 00 00 .`...0@P...!....
00 02 FE 10 00 02 FF A0 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
10:38:30 PM #19 Text 0 File WriterStatus.cpp, Line 116
<E: HP DVD Writer 740b> start writing Lead-Out at LBA 1928672 (1D6DE0h), length 0 blocks
10:38:30 PM #20 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion
10:38:30 PM #21 Text 0 File DVDR.cpp, Line 2978
EndDAO: Last written address was 1928671
10:38:57 PM #22 Phase 37 File dlgbrnst.cpp, Line 1725
Burn process completed successfully at 16x (22,160 KB/s)
10:38:59 PM #23 Phase 78 File dlgbrnst.cpp, Line 1725
Data verification started
10:50:39 PM #24 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion
10:50:40 PM #25 Phase 80 File dlgbrnst.cpp, Line 1725
Data verification completed successfully
Existing drivers:
File 'Drivers\PXHELP20.SYS': Ver=2.03.32a, size=20640 bytes, created 4/25/2005 6:03:00 PM (Prassi/Veritas driver for win 2K)
Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
====== *** Nero Burning ROM, History File *** ======
|
AfterDawn Addict
|
25. June 2006 @ 15:11 |
Link to this message
|
Quote:
I am using Nero 7.0.1.2 Ultra Edition plz help
Not according to your logs
Quote:
Disc Manufacturer: CMC MA - G. AM3
These are horrible discs, try Verbatim or sony (made in japan)
Quote:
Burn process started at 16x (22,160 KB/s)
Way too fast, slow to 4X
Quote:
===== *** Nero Burning ROM, History File *** ======
Carlos
Ramos family
1C83-7613-10E5-477X-4022-xxxx xxxx
Edit out your serial number
Quote:
NT-SPTI used
Nero Version: 7.2.0.3
Internal Version: 7, 2, 0, 3
Heres my suggestion
Nero API version: 7.2.0.3 and 7.2.0.3b
These latest versions of Nero are full of bugs, I recommend you uninstall, run this clean tool http://ww2.nero.com/nero7/enu/Nero7_CleanTool.html and then install 7.0.8.2 a more stable version from here
http://www.filehippo.com/download_nero_7_premium/?845
Quote:
Physical memory : 503MB (515372kB)
Free physical memory: 37MB (38196kB)
Memory in use : 92
Try to free up some memory, however this is one thing that this version does, use lots of memory
You have several logs here, but the main thing is get rid of 7.2.0.3 get different discs and burn at 4X
This message has been edited since posting. Last time this message was edited on 25. June 2006 @ 15:13
|
Newbie
|
26. June 2006 @ 03:39 |
Link to this message
|
|
I uninstall the other version and I am downloading the 7.0.8.2 version that you told me. How can I edit out my serial number? Thanks a lot for all your help so far.
vr. carlucho
|
|
Advertisement
|
|
|
|
Saltgrass
Senior Member
|
26. June 2006 @ 05:23 |
Link to this message
|
|
It looks like you have more than your serial number, also your family name. There are several instances of it.
To edit your post, click on the upper right of the message. The log file usually has one entry for every burn attempt. The last entries are the newest. If you can see where they start and end, you might remove some of the earlier ones at the top to make it easier to read. Especially when you have changed versions as you did.
The one question I have, if you look at the DVD that doesn't show anything, does it appear to have been written on? If you don't know what I mean by that, just compare that DVD with a new one and see if there is any difference in coloration on the burning side.
Nero 7 v7.10.1.0
P4 2.4GHz 1 Gig RAM
NEC ND3550A DVD Burner
|
|
