|
|
|
Lite-On LH-18A1P
|
|
|
Notready
Newbie
|
23. February 2007 @ 02:57 |
Link to this message
|
|
Is this burner junk? I am throwing away 25% of my dvds. I get different errors:
Power calibration error
Write error
Yesterdays I received this error (write error) on 3 of them. I have tried burning at slower rates. (I don't understand this because with previous burners I burned @ 16x with no problems). Under another forum I found a result for googling an error to change IMAPI CD burning COM services under admin tools in the control panel to "disabled". I don't know what that even is, but it didn't help. I changed the firmware yesterday from GLOC to GLOF. I buy my media from bestbuy. Currently I have Fuji, Sony, and Verb. Prior to the firmware update the burner couldn't recognize the Sonys so that is a + since I have about 120 of them still from a sale last year. I burned 10 dvds yesterday and wasted 4 (4/14). With other burners in the past with similar media from Bestbuy I might throw away one in a cake of 50.
Any ideas? Did I leave anything out?
|
|
Advertisement
|
|
|
|
AfterDawn Addict
|
23. February 2007 @ 06:12 |
Link to this message
|
|
POsts the log of your failed burn here. Last one only please.
|
|
Notready
Newbie
|
23. February 2007 @ 08:46 |
Link to this message
|
I don't know if you need all of this. Sorry if this is long. Thanks for looking. How many burners are just defective or bad from the shelf?
Quote:
Windows XP 5.1
IA32
WinAspi: -
NT-SPTI used
Nero Version: 7.2.3.3
Internal Version: 7, 2, 3, 3
(Nero Express)
Recorder: <LITE-ON DVDRW LH-18A1P> Version: GL0F - HA 1 TA 2 - 7.2.3.3
Adapter driver: <IDE> HA 1
Drive buffer : 2048kB
Bus Type : via Inquiry data (1) -> ATAPI, detected: ?
Connected to MMC as unknown drive with class-nr : 1
Drive is autodetected - recorder class: Std. MMC recorder
CD-ROM: <LITE-ON DVDRW LH-18A1P >Version: GL0F - HA 1 TA 2 - 7.2.3.3
Adapter driver: <IDE> HA 1
=== Scsi-Device-Map ===
DiskPeripheral : WDC WD400JB-00ENA0 atapi Port 0 ID 0 DMA: On
DiskPeripheral : WDC WD1200JB-00EVA0 atapi Port 0 ID 1 DMA: On
DiskPeripheral : WDC WD2000JD-22HBC0 atapi Port 1 ID 0 DMA: On
DiskPeripheral : WDC WD5000AAKS-00TMA0 atapi Port 2 ID 0 DMA: On
CdRomPeripheral : LITE-ON DVDRW LH-18A1P atapi Port 3 ID 0 DMA: On
=== CDRom-Device-Map ===
LITE-ON DVDRW LH-18A1P F: CDRom2
=======================
AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 83886080 (0) Byte
BUFE : 0
Physical memory : 1023MB (1048048kB)
Free physical memory: 435MB (445504kB)
Memory in use : 57 %
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)
22.2.2007
ISO compilation
22:09:23 #1 Text 0 File Isodoc.cpp, Line 6427
Iso document burn settings
------------------------------------------
Determine maximum speed : FALSE
Simulate : FALSE
Write : TRUE
Finalize CD : TRUE
Multisession : FALSE
Burning mode : DAO
Mode : 1
ISO Level : 1 (Max. of 11 = 8 + 3 char)
Character set : ISO 9660
Joliet : TRUE
Allow pathdepth more than 8 directories : TRUE
Allow more than 255 characters in path : TRUE
Write ISO9660 ;1 file extensions : TRUE
22:09:23 #2 Text 0 File ThreadedTransfer.cpp, Line 531
ReadBuffer-Pipe got 262144KB of Memory
22:09:23 #3 Text 0 File Reader.cpp, Line 124
Reader running
22:09:23 #4 Text 0 File Writer.cpp, Line 113
Writer F: LITE-ON DVDRW LH-18A1P running
22:09:23 #5 ISO9660GEN -11 File Geniso.cpp, Line 3312
First writeable address = 0 (0x00000000)
22:09:23 #6 Text 0 File Burncd.cpp, Line 3400
Turn on Disc-At-Once, using DVD media
22:09:23 #7 Text 0 File DlgWaitCD.cpp, Line 290
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 2289791 (508:50.41, 4472MB)
22:09:23 #8 Text 0 File DlgWaitCD.cpp, Line 302
Write in overburning mode: NO (enabled: CD)
22:09:23 #9 Text 0 File DlgWaitCD.cpp, Line 2733
Recorder: LITE-ON DVDRW LH-18A1P, Media type: DVD-R
Disc Manufacturer: SONY16 - D1
Disc Application Code: 64, Disc Physical Code: 193
22:09:23 #10 Text 0 File DlgWaitCD.cpp, Line 474
>>> Protocol of DlgWaitCD activities: <<<
=========================================
22:09:23 #11 Text 0 File ThreadedTransferInterface.cpp, Line 847
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
2 indices, index0 (150) not provided
original disc pos #0 + 2289792 (2289792) = #2289792/508:50.42
relocatable, disc pos for caching/writing not required/ required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2289792 blocks [F: LITE-ON DVDRW LH-18A1P]
--------------------------------------------------------------
22:09:23 #12 Text 0 File ThreadedTransferInterface.cpp, Line 1059
Prepare recorder [F: LITE-ON DVDRW LH-18A1P] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4689494016, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
2289792 | lead-out | 1 | 0x41 | 0x00
22:09:23 #13 Text 0 File SCSIPassThrough.cpp, Line 39
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME
22:09:23 #14 Phase 24 File dlgbrnst.cpp, Line 1730
Caching of files started
22:09:23 #15 Text 0 File Burncd.cpp, Line 4231
Cache writing successful.
22:09:23 #16 Phase 25 File dlgbrnst.cpp, Line 1730
Caching of files completed
22:09:23 #17 Phase 36 File dlgbrnst.cpp, Line 1730
Burn process started at 8x (11,080 KB/s)
22:09:23 #18 Text 0 File ThreadedTransferInterface.cpp, Line 2707
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0
22:09:24 #19 Text 0 File DVDR.cpp, Line 2905
Recording mode: Sequential Recording Mode
22:09:24 #20 Text 0 File DVDR.cpp, Line 3061
Start write address at LBA 0
DVD high compatibility mode: Yes
22:09:24 #21 Text 0 File Cdrdrv.cpp, Line 8995
---- DVD Structure: Physical Format Information (00h) ----
Media Type: 0, Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 2.1 (33)
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 26127F h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 0 h
Start sector number of the next Border-In: 0 h
Media Specific [16..63]:
00 60 00 10 20 30 40 50 - 00 00 00 21 00 00 00 00 .`...0@P...!....
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
22:09:58 #22 Text 0 File Cdrdrv.cpp, Line 1224
22:09:58.609 - F: LITE-ON DVDRW LH-18A1P : Queue again later
22:12:01 #23 SPTI -1135 File SCSIPassThrough.cpp, Line 291
F: CdRom2: SCSIStatus(x02) WinError(0) NeroError(-1135)
Sense Key: 0x03 (KEY_MEDIUM_ERROR)
Sense Code: 0x0C
Sense Qual: 0x00
CDB Data: 0x2A 00 00 05 EE A0 00 00 20 00 00 00
Sense Area: 0x70 00 03 00 00 00 00 0A 00 00 00 00 0C
Buffer x04760000: Len x10000
0x00 00 01 BA 44 92 DD 42 4E 03 01 89 C3 F8 00 00
0x01 E0 07 EC 81 00 00 0F 96 3F CA 76 01 6B C1 EC
0x71 16 0E 6B B4 0F 63 08 77 80 6B 38 10 63 C8 FE
22:12:01 #24 CDR -1135 File Writer.cpp, Line 302
Write error
F: LITE-ON DVDRW LH-18A1P
22:12:01 #25 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion
22:12:01 #26 Text 0 File ThreadedTransfer.cpp, Line 222
conversion idle, stopping reader
22:12:01 #27 Text 0 File DVDR.cpp, Line 3301
EndDAO: Last written address was 388767
22:12:01 #28 Phase 38 File dlgbrnst.cpp, Line 1730
Burn process failed at 8x (11,080 KB/s)
Existing drivers:
File 'Drivers\PXHELP20.SYS': Ver=2.03.32a, size=20640 bytes, created 4/25/2005 03:03:00 (Prassi/Veritas driver for win 2K)
Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
|
|
Notready
Newbie
|
23. February 2007 @ 08:51 |
Link to this message
|
I don't see any way to edit my latest post. (sorry) I tried imgburn also and that failed and the trial/simulation even failed so I uninstalled it. Nero always worked for me but everyone raves about it so I tried it. Didn't even work once for me.
|
|
Notready
Newbie
|
23. February 2007 @ 14:32 |
Link to this message
|
|
I have wasted 4 more dvds now. On the last one I received a msg when closing it. I captured it but can't upload it here. It was a msg saying I need the wnaspi.dll. (This application has failed to start because wnaspi.dll was not found. Re-installing the application may fix this problem) I d/l this file but I don't know where it goes. I read in '98 it's in the system folder. I have XP, so should it go in the system folder or system32?
|
AfterDawn Addict
|
24. February 2007 @ 01:53 |
Link to this message
|
|
|
Car.Mike
AfterDawn Addict
|
24. February 2007 @ 04:00 |
Link to this message
|
|
Notready,
Your burn error is below. The burner is not recog the blank media you are using. Have you tried (+)DVD's to see if it does this. I have that burner but I only use (+) DVD made by Verbatim and Taiyo Yuden and then I bookset the drive to DVD-Rom. It still should be under warranty and if it fails w/ (+)DVD's then I would take it back.
22:12:01 #23 SPTI -1135 File SCSIPassThrough.cpp, Line 291
F: CdRom2: SCSIStatus(x02) WinError(0) NeroError(-1135)
Sense Key: 0x03 (KEY_MEDIUM_ERROR)
Sense Code: 0x0C
|
|
Notready
Newbie
|
24. February 2007 @ 06:52 |
Link to this message
|
Originally posted by Car.Mike:
Notready,
Your burn error is below. The burner is not recog the blank media you are using. Have you tried (+)DVD's to see if it does this. I have that burner but I only use (+) DVD made by Verbatim and Taiyo Yuden and then I bookset the drive to DVD-Rom. It still should be under warranty and if it fails w/ (+)DVD's then I would take it back.
22:12:01 #23 SPTI -1135 File SCSIPassThrough.cpp, Line 291
F: CdRom2: SCSIStatus(x02) WinError(0) NeroError(-1135)
Sense Key: 0x03 (KEY_MEDIUM_ERROR)
Sense Code: 0x0C
I currently have 3 different kinds of media. (verb, fuji, and sony) All are DVD-R. I was using the minuses with the last burner which was the predecessor to this burner.
I also found the .dll file on the other installation of windows I have on a different partition. I copied it to the this one which I found in the system32 folder. I have only burned 2 dvds so far, but we'll see how it goes! Maybe I'll try to see if the place I bought it from will take it back.
thanks
|
|
Notready
Newbie
|
24. February 2007 @ 19:41 |
Link to this message
|
I only got a few seconds into a burn with a DVD+R and it failed with a power calibration error. So now I have 4 different brands of media, both + and - and about a total of 200 dvdrs now. I don't think this burner likes anything.
|
|
Car.Mike
AfterDawn Addict
|
25. February 2007 @ 01:47 |
Link to this message
|
|
Take it back for either exchange or get another brand. There is no sense in worrying too much about as you can get a bad one
|
|
Munch58
Suspended due to non-functional email address
|
25. February 2007 @ 10:22 |
Link to this message
|
Use DVDFab and ImgBurn....I don't use Nero anymore and have alot less headaches.
|
|
Notready
Newbie
|
25. February 2007 @ 11:23 |
Link to this message
|
Originally posted by Munch58:
Use DVDFab and ImgBurn....I don't use Nero anymore and have alot less headaches.
I tried ImgBurn but I could not get it to work. I don't know anything DVDFab. I will try that but I bought another burner and hopefully they will take this one and exchange it or something. I'm pretty sure they say I have some other pc problem through. When I go there and the guy looks at the device mgr he says I have some other problem and I need to fix that first. When I look at it looks like this 
This is taken from this page: http://support.packardbell.com/se/item/i...&ppn=PB14303191
I do not have a packardbell or whatever it is. I know when I look at my device mgr I have 2 under each of IDE controllers though. I have my bios for both PATA & SATA otherwise I can't use all my HDs. Anyway, when he sees that he will say that is the problem.
|
|
Advertisement
|
|
|
|
Munch58
Suspended due to non-functional email address
|
25. February 2007 @ 14:20 |
Link to this message
|
I have 3 primary IDE and 3 secondary IDE showing in my device manager. I have 6 SATA connections and 1 IDE connection. My hd shows up on the primary and my 2 optical drives show up on secondary IDE. Let me know how your drive return goes. Also, ImgBurn has excellent walkthroughs here. http://www.imgburn.com/ Click on the guides tab. DVDFab Platinum is free to try and $49.95 to buy...well worth it IMO. It can shrink, remove cp's and burn all in one step.
This message has been edited since posting. Last time this message was edited on 25. February 2007 @ 14:23
|
|
