|
|
|
Reset Error etc Please Help.
|
|
|
Dslord017
Newbie
|
21. June 2007 @ 11:28 |
Link to this message
|
I have a LG dual Layer Burner (GSA-H50L)and using RiData DVD-R DL 4X DVD's.
I can burn movie copies on single layers no problem but when I try Dual layer burns when it get's to the second layer it always fails. Sometimes not right away but it does eventually.
I am successful with similuations but fail when it comes to the real burn.
I have used the Nero clean up tool and re-installed with the lastest version.
The last 2 errors I have received have been reset errors. Previously I have had a no seek error, and I think someting like track following error as well.
I have exchanged the burner and still the same results.
The log error is as follows
Windows XP 5.1
IA32
WinAspi: -
NT-SPTI used
Nero Version: 7.9.6.0
Internal Version: 7, 9, 6, 0
Recorder: <HL-DT-ST DVD-RAM GSA-H50L>Version: 1.00 - HA 1 TA 0 - 7.9.6.0
Adapter driver: <IDE> HA 1
Drive buffer : 2048kB
Bus Type : default (0) -> ATAPI, detected: ?
CD-ROM: <HL-DT-ST DVD-RAM GSA-H50L>Version: 1.00 - HA 1 TA 0 - 7.9.6.0
Adapter driver: <IDE> HA 1
=== Scsi-Device-Map ===
DiskPeripheral : WDC WD800JB-00ETA0 atapi Port 0 ID 0 DMA: On
DiskPeripheral : WDC WD400BB-53AUA1 atapi Port 0 ID 1 DMA: On
CdRomPeripheral : HL-DT-ST DVD-RAM GSA-H50L atapi Port 1 ID 0 DMA: On
CdRomPeripheral : HL-DT-ST DVDRAM GSA-4163B atapi Port 1 ID 1 DMA: On
=== CDRom-Device-Map ===
HL-DT-ST DVD-RAM GSA-H50L F: CdRom0
HL-DT-ST DVDRAM GSA-4163B H: CdRom1
=======================
AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 83886080 (0) Byte
BUFE : 0
Physical memory : 767MB (785904kB)
Free physical memory: 319MB (326984kB)
Memory in use : 58 %
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)
21.6.2007
Burn DVD Image
11:09:02 PM #1 Text 0 File SCSIPTICommands.cpp, Line 424
LockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL
11:09:02 PM #2 Text 0 File Burncd.cpp, Line 3508
Turn on Disc-At-Once, using DVD media
11:09:02 PM #3 Text 0 File DlgWaitCD.cpp, Line 307
Last possible write address on media: 4172815 (927:17.40, 8150MB)
Last address to be written: 3505100 (778:54.50, 6845MB)
11:09:02 PM #4 Text 0 File DlgWaitCD.cpp, Line 319
Write in overburning mode: NO (enabled: CD)
11:09:02 PM #5 Text 0 File DlgWaitCD.cpp, Line 2964
Recorder: HL-DT-ST DVD-RAM GSA-H50L, Media type: DVD-R Dual Layer
Disc Manufacturer: RITEKP - 01
Disc Application Code: 2, Disc Physical Code: 145
11:09:02 PM #6 Text 0 File DlgWaitCD.cpp, Line 493
>>> Protocol of DlgWaitCD activities: <<<
=========================================
11:09:02 PM #7 Text 0 File ThreadedTransferInterface.cpp, Line 793
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 (2 - CD-ROM Mode 1, ISO 9660)
2 indices, index0 (150) not provided
original disc pos #0 + 3505101 (3505101) = #3505101/778:54.51
not relocatable, disc pos for caching/writing not required/not required
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 3505101 blocks [F: HL-DT-ST DVD-RAM GSA-H50L]
--------------------------------------------------------------
11:09:02 PM #8 Text 0 File ThreadedTransferInterface.cpp, Line 995
Prepare [F: HL-DT-ST DVD-RAM GSA-H50L] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1: Idx 0 Idx 1 Next Trk
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 7178446848, ISRC ""
DAO layout:
===========
___Start_|____Track_|_Idx_|_CtrlAdr_|_____Size_|______NWA_|_RecDep__________
0 | lead-in | 0 | 0x41 | 0 | 0 | 0x00
0 | 1 | 0 | 0x41 | 0 | 0 | 0x00
0 | 1 | 1 | 0x41 | 3505101 | 3505101 | 0x00
3505101 | lead-out | 1 | 0x41 | 0 | 0 | 0x00
11:09:03 PM #9 Text 0 File SCSIPTICommands.cpp, Line 215
SPTILockVolume - completed successfully for FSCTL_LOCK_VOLUME
11:09:03 PM #10 Text 0 File Burncd.cpp, Line 4294
Caching options: cache CDRom or Network-Yes, small files-No (<64KB)
11:09:03 PM #11 Phase 24 File dlgbrnst.cpp, Line 1762
Caching of files started
11:09:03 PM #12 Text 0 File Burncd.cpp, Line 4413
Cache writing successful.
11:09:03 PM #13 Phase 25 File dlgbrnst.cpp, Line 1762
Caching of files completed
11:09:03 PM #14 Phase 32 File dlgbrnst.cpp, Line 1762
Simulation started at 4x (5,540 KB/s)
11:09:03 PM #15 Text 0 File ThreadedTransferInterface.cpp, Line 2721
Verifying disc position of item 0 (not relocatable, no disc pos, no patch infos, orig at #0): write at #0
11:09:03 PM #16 Text 0 File DVDPlusDualLayer.cpp, Line 494
Disc finalized, LBA total Image size: 3505101 (6845MB), Last LBA L0: 1752559 (3422MB)
11:09:03 PM #17 Text 0 File DVDPlusDualLayer.cpp, Line 670
L0 Data Zone Capacity not set.
Max LBA L0 2092895 (1FEF5Fh, 4087MB), next writable address 0 (0h, 0MB)
11:09:03 PM #18 CDR -1205 File DVDPlusDualLayer.cpp, Line 686
Burning Layer 1
11:09:03 PM #19 Text 0 File DVDPlusDualLayer.cpp, Line 696
Start writing layer 1 at address 0 (0h)
Recording mode: unknown Recording Mode
11:09:03 PM #20 Text 0 File DVDR.cpp, Line 3225
Recording mode: Sequential Recording Mode
11:09:03 PM #21 Text 0 File DVDR.cpp, Line 3381
Start write address at LBA 0
DVD high compatibility mode: Yes
11:09:03 PM #22 Text 0 File Cdrdrv.cpp, Line 9872
---- Disc Structure: Physical Format Information (00h) ----
Media Type: 0, Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: - (6), Extended Part Version: 3.0 (48)
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 2, Track Path: Opposite Track Path (OTP), Layer Type: recordable
Linear Density: 0,293 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Sector Number in Layer 0: 22EF5F h (LBN: 1FEF5F h, 4087 MB)
Data in Burst Cutting Area (BCA) does not exist
Revision number of maximum recording speed: 1.0
Revision number of minimum recording speed: -
Revision number table of recording speed: - - - - - - -
Class: 0
Start sector number of the current Border-Out: 2FE10 h
Start sector number of the next Border-In: 2FFA0 h
Media Specific [16..63]:
00 10 00 00 00 00 00 00 - 00 00 00 30 00 00 00 00 ...........0....
00 02 FE 10 00 02 FF A0 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
11:09:03 PM #23 Text 0 File DVDR.cpp, Line 3517
Reserved Track size: 3505104 (357BD0h, 6845MB) -> return code 0
11:09:03 PM #24 Text 0 File ThreadedTransfer.cpp, Line 269
Pipe memory size 83836800
11:22:10 PM #25 CDR -1206 File DVDPlusDualLayer.cpp, Line 1969
Burning Layer 2
11:22:10 PM #26 Text 0 File DVDPlusDualLayer.cpp, Line 1980
Perform layer 1 to 2 jump before writing at address 2092896 (1FEF60h)
11:31:04 PM #27 Text 0 File WriterStatus.cpp, Line 113
<F: HL-DT-ST DVD-RAM GSA-H50L> start writing Lead-Out at LBA 3505101 (357BCDh), length 0 blocks
11:31:04 PM #28 Phase 181 File dlgbrnst.cpp, Line 1762
Writing lead-out...
11:36:14 PM #29 Text 0 File DVDR.cpp, Line 3783
EndDAO: Last written address was 3505100 (357BCCh)Estimated time for completing DVD-R DL disc: 5min 01sec
11:36:15 PM #30 Phase 33 File dlgbrnst.cpp, Line 1762
Simulation completed successfully at 4x (5,540 KB/s)
11:36:16 PM #31 Phase 36 File dlgbrnst.cpp, Line 1762
Burn process started at 4x (5,540 KB/s)
11:36:16 PM #32 Text 0 File ThreadedTransferInterface.cpp, Line 2721
Verifying disc position of item 0 (not relocatable, no disc pos, no patch infos, orig at #0): write at #0
11:36:16 PM #33 Text 0 File DVDPlusDualLayer.cpp, Line 494
Disc finalized, LBA total Image size: 3505101 (6845MB), Last LBA L0: 1752559 (3422MB)
11:36:16 PM #34 Text 0 File DVDPlusDualLayer.cpp, Line 670
L0 Data Zone Capacity not set.
Max LBA L0 2092895 (1FEF5Fh, 4087MB), next writable address 0 (0h, 0MB)
11:36:16 PM #35 CDR -1205 File DVDPlusDualLayer.cpp, Line 686
Burning Layer 1
11:36:16 PM #36 Text 0 File DVDPlusDualLayer.cpp, Line 696
Start writing layer 1 at address 0 (0h)
Recording mode: unknown Recording Mode
11:36:16 PM #37 Text 0 File DVDR.cpp, Line 3225
Recording mode: Sequential Recording Mode
11:36:16 PM #38 Text 0 File DVDR.cpp, Line 3381
Start write address at LBA 0
DVD high compatibility mode: Yes
11:36:16 PM #39 Text 0 File Cdrdrv.cpp, Line 9872
---- Disc Structure: Physical Format Information (00h) ----
Media Type: 0, Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: - (6), Extended Part Version: 3.0 (48)
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 2, Track Path: Opposite Track Path (OTP), Layer Type: recordable
Linear Density: 0,293 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Sector Number in Layer 0: 22EF5F h (LBN: 1FEF5F h, 4087 MB)
Data in Burst Cutting Area (BCA) does not exist
Revision number of maximum recording speed: 1.0
Revision number of minimum recording speed: -
Revision number table of recording speed: - - - - - - -
Class: 0
Start sector number of the current Border-Out: 2FE10 h
Start sector number of the next Border-In: 2FFA0 h
Media Specific [16..63]:
00 10 00 00 00 00 00 00 - 00 00 00 30 00 00 00 00 ...........0....
00 02 FE 10 00 02 FF A0 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
11:36:16 PM #40 Text 0 File DVDR.cpp, Line 3517
Reserved Track size: 3505104 (357BD0h, 6845MB) -> return code 0
11:36:16 PM #41 Text 0 File ThreadedTransfer.cpp, Line 269
Pipe memory size 83836800
11:59:41 PM #42 SPTI -1114 File SCSIPassThrough.cpp, Line 179
CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1114)
Sense Key: 0x06 (KEY_UNIT_ATTENTION)
Sense Code: 0x29
Sense Qual: 0x00
CDB Data: 0x2A 00 00 1F EF 40 00 00 20 00 00 00
Sense Area: 0x70 00 06 00 00 00 00 0E 00 00 00 00 29
Buffer x08023840: Len x10000
0x00 00 01 BA 44 1C 87 34 0C 97 01 89 C3 F8 00 00
0x01 E0 07 EC 81 00 00 9A 70 D0 B2 82 5B DD F5 F7
0xC0 03 F3 72 D2 6D B4 84 50 47 A5 6F 3C 44 FB ED
11:59:41 PM #43 CDR -1114 File Writer.cpp, Line 303
Reset occurred
F: HL-DT-ST DVD-RAM GSA-H50L
11:59:41 PM #44 Phase 181 File dlgbrnst.cpp, Line 1762
Writing lead-out...
12:02:36 AM #45 Text 0 File DVDR.cpp, Line 3783
EndDAO: Last written address was 2092863 (1FEF3Fh)Estimated time for completing DVD-R DL disc: 13min 30sec
12:02:36 AM #46 Phase 38 File dlgbrnst.cpp, Line 1762
Burn process failed at 4x (5,540 KB/s)
12:02:37 AM #47 Text 0 File SCSIPTICommands.cpp, Line 261
SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME
12:02:44 AM #48 Text 0 File Cdrdrv.cpp, Line 11185
DriveLocker: UnLockVolume completed
12:02:44 AM #49 Text 0 File SCSIPTICommands.cpp, Line 424
UnLockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL
Existing drivers:
Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
Any help would be appreciated.
Thanks
|
|
laddyboy
AfterDawn Addict
|
21. June 2007 @ 12:09 |
Link to this message
|
There's a newer firmware for your burner, version 1.01, here:
http://us.lgservice.com/index_b2c.jsp
That may or may not solve your problem.
You could also try creating an ISO image of your project and burning with ImgBurn:
http://www.imgburn.com
Ridata media isn't the best and is harder to burn than Verbatim for many burners.
|
|
