|
|
|
Burning Music to DL DVD+R error
|
|
|
Jeraal
Newbie
|
8. August 2007 @ 18:34 |
Link to this message
|
[/b]Firstly I'd like to thank in advance those that take the time to reply and help me. I may have figured out the problem, however I would like some confirmation before I rip my system apart :)
Nero Version: 7.10.1.0 When burning music (a data disc) to a DVD (I tried single layer and dual) it burned about 2%, then stopped. Nero ran for about 7 minutes longer, then ejected the disc. I'll post the small log at the end.
I did some searching, and discovered hobbit112 reply to Florence1 post. I followed his/her insructions in the aforementioned post. Everything went as expected until I tried to change the IDE transfer mode from PIO to DMA.
Device 0 is set to DMA if available and Current Transfer Mode is Ultra DMA Mode 2. Device 1 is set to DMA mode if available however, CTM is set to PIO with no option to switch to DMA. I have uninstalled the device, and let windows reinstall it twice, with the same result, DMA does not appear. Drivers are up to date, but in this old Dell I picked up, the original DVD read only is set to Master, and I have a new LG GSA-H54N set to slave. Is it possible that I should move the burner to master and the reader to slave? Would that have any affect on the DMA/PIO setting?
Log as follows:
Windows XP 5.1
IA32
WinAspi: -
NT-SPTI used
Nero Version: 7.10.1.0
Internal Version: 7, 10, 1, 0
(Nero Express)
Recorder: ram.cfm" class="forum_link" target="_blank">DVD-RAM GSA-H54N>Version: 1.00 - HA 1 TA 1 - 7.10.1.0
Adapter driver: HA 1
Drive buffer : 2048kB
Bus Type : default (0) -> ATAPI, detected: ?
CD-ROM: DVD-ROM XJ-HD166>Version: DD05 - HA 1 TA 0 - 7.10.1.0
Adapter driver: HA 1
=== Scsi-Device-Map ===
DiskPeripheral : WDC WD1200JD-75GBB0 iaStor Port 0 ID 0 DMA: On
CdRomPeripheral : JLMS DVD-ROM XJ-HD166 atapi Port 1 ID 0 DMA: On
CdRomPeripheral : HL-DT-ST DVD-RAM GSA-H54N atapi Port 1 ID 1 DMA: Off
=== CDRom-Device-Map ===
JLMS DVD-ROM XJ-HD166 D: CdRom0
HL-DT-ST DVD-RAM GSA-H54N E: CdRom1
=======================
AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 83886080 (0) Byte
BUFE : 0
Physical memory : 1023MB (1047552kB)
Free physical memory: 555MB (568908kB)
Memory in use : 45 %
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)
6.8.2007
ISO compilation
5:32:14 PM #1 Text 0 File SCSIPTICommands.cpp, Line 424
LockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL
5:32:14 PM #2 Text 0 File Isodoc.cpp, Line 6666
Iso document burn settings
------------------------------------------
Determine maximum speed : FALSE
Simulate : FALSE
Write : TRUE
Finalize CD : TRUE
Multisession : FALSE
Burning mode : DAO
Mode : 1
ISO Level : 1 (Max. of 11 = 8 + 3 char)
Character set : ISO 9660
Joliet : TRUE
Allow pathdepth more than 8 directories : FALSE
Allow more than 255 characters in path : FALSE
Write ISO9660 ;1 file extensions : TRUE
5:32:14 PM #3 ISO9660GEN -11 File Geniso.cpp, Line 3343
First writeable address = 0 (0x00000000)
5:32:14 PM #4 Text 0 File Burncd.cpp, Line 3508
Turn on Disc-At-Once, using DVD media
5:32:14 PM #5 Text 0 File DlgWaitCD.cpp, Line 307
Last possible write address on media: 2295103 (510:01.28, 4482MB)
Last address to be written: 2198799 (488:37.24, 4294MB)
5:32:14 PM #6 Text 0 File DlgWaitCD.cpp, Line 319
Write in overburning mode: NO (enabled: CD)
5:32:14 PM #7 Text 0 File DlgWaitCD.cpp, Line 2972
Recorder: HL-DT-ST DVD-RAM GSA-H54N, Media type: DVD+R
Disc Manufacturer ID: YUDEN000, Media Type ID: T02, Product revision number: 0
Disc Application Code: 0, Extended Information Indicators: 3
5:32:14 PM #8 Text 0 File DlgWaitCD.cpp, Line 493
>>> Protocol of DlgWaitCD activities: <<<
=========================================
5:32:14 PM #9 Text 0 File ThreadedTransferInterface.cpp, Line 793
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
2 indices, index0 (150) not provided
original disc pos #0 + 2198800 (2198800) = #2198800/488:37.25
relocatable, disc pos for caching/writing not required/ required
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2198800 blocks [E: HL-DT-ST DVD-RAM GSA-H54N]
--------------------------------------------------------------
5:32:14 PM #10 Text 0 File ThreadedTransferInterface.cpp, Line 995
Prepare [E: HL-DT-ST DVD-RAM GSA-H54N] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1: Idx 0 Idx 1 Next Trk
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4503142400, ISRC ""
DAO layout:
===========
___Start_|____Track_|_Idx_|_CtrlAdr_|_____Size_|______NWA_|_RecDep__________
0 | lead-in | 0 | 0x41 | 0 | 0 | 0x00
0 | 1 | 0 | 0x41 | 0 | 0 | 0x00
0 | 1 | 1 | 0x41 | 2198800 | 0 | 0x00
2198800 | lead-out | 1 | 0x41 | 0 | 0 | 0x00
5:32:14 PM #11 Text 0 File SCSIPTICommands.cpp, Line 215
SPTILockVolume - completed successfully for FSCTL_LOCK_VOLUME
5:32:14 PM #12 Text 0 File Burncd.cpp, Line 4294
Caching options: cache CDRom or Network-Yes, small files-Yes (<64KB)
5:32:14 PM #13 Phase 24 File dlgbrnst.cpp, Line 1762
Caching of files started
5:32:14 PM #14 Text 0 File Burncd.cpp, Line 4413
Cache writing successful.
5:32:14 PM #15 Phase 25 File dlgbrnst.cpp, Line 1762
Caching of files completed
5:32:14 PM #16 Phase 36 File dlgbrnst.cpp, Line 1762
Burn process started at 4x (5,540 KB/s)
5:32:14 PM #17 Text 0 File ThreadedTransferInterface.cpp, Line 2721
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0
5:32:15 PM #18 Text 0 File Cdrdrv.cpp, Line 9872
---- Disc Structure: Physical Format Information (00h) ----
Media Type: 0, Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD+R (10), Part Version: 1.0x (1)
Disc Size: 120 mm, Maximum Rate: (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Disc Application Code: 0 / 0 h
Extended Information indicators: 3 h
Disc Manufacturer ID: YUDEN000
Media type ID: T02
Product revision number: 0
Number of Physical format information bytes in use in ADIP up to byte 63: 56
Media Specific [16..63]:
00 00 03 59 55 44 45 4E - 30 30 30 54 30 32 00 38 ...YUDEN000T02.8
23 54 37 10 02 4E 72 02 - 8C 63 16 16 0B 0B 0A 0A #T7..Nr.îc......
01 19 1B 0C 0C 0C 0D 01 - 00 00 00 00 00 00 00 00 ................
5:32:15 PM #19 Text 0 File DVDR.cpp, Line 6553
Drive: HL-DT-ST DVD-RAM GSA-H54N
Book Type request [LG]: DVD-ROM
Changing the Book Type was finished successfully, return code 0
5:32:15 PM #20 CDR -1207 File DVDR.cpp, Line 6477
Book Type automatically set to: DVD-ROM
5:32:15 PM #21 SPTI -1066 File SCSIPassThrough.cpp, Line 179
CdRom1: SCSIStatus(x02) WinError(0) NeroError(-1066)
Sense Key: 0x05 (KEY_ILLEGAL_REQUEST)
Sense Code: 0x24
Sense Qual: 0x00
CDB Data: 0xAC 00 00 00 00 00 00 00 00 64 00 00
Sense Area: 0x70 00 05 00 00 00 00 0E 00 00 00 00 24
Buffer x06312580: Len x648
5:32:15 PM #22 Text 0 File DVDPlusRW.cpp, Line 675
Start write address at LBA 0
DVD high compatibility mode: Yes
5:32:15 PM #23 Text 0 File ThreadedTransfer.cpp, Line 269
Pipe memory size 83836800
5:42:47 PM #24 SPTI -600 File SCSIPassThrough.cpp, Line 179
CdRom1: SCSIStatus(x00) WinError(121) NeroError(-600)
Sense Key: 0x00 (KEY_NO_SENSE)
Sense Code: 0x00
Sense Qual: 0x00
CDB Data: 0x2A 00 00 00 24 40 00 00 20 00 00 00
Sense Area: 0x00 00 00 00 00 00 00 00 00 00 00 00 00
Buffer x09af48c0: Len x10000
0xC6 29 0F 04 86 24 13 E2 01 59 E1 1B 4A 39 AA 14
0x55 87 BB 3D 27 A2 94 D4 AF 41 1D 2C 7D 13 32 B2
0xA9 AA 1F 4F 73 DB 25 1E FE 76 D3 27 2F B9 87 D7
5:42:47 PM #25 CDR -600 File Writer.cpp, Line 303
Device not available
E: HL-DT-ST DVD-RAM GSA-H54N
5:42:47 PM #26 SPTI -1114 File SCSIPassThrough.cpp, Line 179
CdRom1: SCSIStatus(x02) WinError(0) NeroError(-1114)
Sense Key: 0x06 (KEY_UNIT_ATTENTION)
Sense Code: 0x29
Sense Qual: 0x00
CDB Data: 0x35 02 00 00 00 00 00 00 00 00 00 00
Sense Area: 0x70 00 06 00 00 00 00 0E 00 00 00 00 29
5:43:04 PM #27 SPTI -1023 File SCSIPassThrough.cpp, Line 179
CdRom1: SCSIStatus(x02) WinError(0) NeroError(-1023)
Sense Key: 0x05 (KEY_ILLEGAL_REQUEST)
Sense Code: 0x2C
Sense Qual: 0x00
CDB Data: 0x5B 01 05 00 00 00 00 00 00 00 00 00
Sense Area: 0x70 00 05 00 00 00 00 0E 00 00 00 00 2C
5:43:04 PM #28 Phase 127 File dlgbrnst.cpp, Line 1762
Generating DVD high compatibility borders
5:43:19 PM #29 Text 0 File DVDPlusRW.cpp, Line 935
EndDAO: Last written address 9280
5:43:19 PM #30 CDR -1114 File WriterStatus.cpp, Line 162
Reset occurred
E: HL-DT-ST DVD-RAM GSA-H54N
5:43:19 PM #31 TRANSFER -24 File WriterStatus.cpp, Line 162
Could not perform end of Disc-at-once
5:43:19 PM #32 Phase 38 File dlgbrnst.cpp, Line 1762
Burn process failed at 4x (5,540 KB/s)
5:43:23 PM #33 Text 0 File SCSIPTICommands.cpp, Line 261
SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME
5:43:29 PM #34 Text 0 File Cdrdrv.cpp, Line 11185
DriveLocker: UnLockVolume completed
5:43:30 PM #35 Text 0 File SCSIPTICommands.cpp, Line 424
UnLockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL
Existing drivers:
Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
|
|
Advertisement
|
 |
|
|
Moderator
|
8. August 2007 @ 20:23 |
Link to this message
|
Hi Jeraal
I think I'd take the pc apart - well the drives out at least.
Dell's usually prefer the jumper pin on the back of the drive to be set to cable select.
Check the older dvd-rom and what it's jumper pin is set too - if this drive came with the dell then it's probably set to cable select.
Change the LG drive to cable select too and see if DMA is enabled.
Here's also a utility from Dell to set the secondary ide channel to DMA (both these drives are on the channel)
Check the jumper pin settings 1st though.
|
|
Jeraal
Newbie
|
8. August 2007 @ 20:46 |
Link to this message
|
Thanks for the reply binkie7 :)
It is getting late here, so tearing the drives out will have to wait for tomorrow. I will follow your advice and check the jumper pin settings, then if that doesnt work, Ill flip the drives.
I was unaware that Dell set their drives to C Select. You learn something new evey day :)
I will post back and let you know what , if anything, worked
Thanks again!
|
Moderator
|
9. August 2007 @ 10:14 |
Link to this message
|
Not a problem Jeraal.
Yeah Dell is one of the only ones that usually have the preference to cable select. So yep check that out.
Keep us posted!
|
Senior Member
|
9. August 2007 @ 12:06 |
Link to this message
|
I was also going to suggest checking in the bios for the DMA selection on the secondary channel. It's been a long time since I've looked over a Dell. Binkie7, I didn't see the link for the utility to change the DMA on the Dell.
|
Moderator
|
9. August 2007 @ 13:35 |
Link to this message
|
Oops it was late :) I forgot to post the link to that Dell utility.
Here you go - link
|
|
Jeraal
Newbie
|
9. August 2007 @ 16:42 |
Link to this message
|
I found the utility binkie :)
I ended up swapping the drives around, and set my burner as master and the dvd-rom as slave. It was set to Cable Select however.
Once I did that had nero rerun the project, and 20 mins later 8 gb of music burned on a DL disc. Worked perfect, thanks for the advice !
|
|
Advertisement
|
|
|
Moderator
|
9. August 2007 @ 18:22 |
Link to this message
|
|
Not a problem
Glad to hear you got it sorted out.
Happy Burning!
|
|
