Help me please! I have been following ScubaPete's direction in EVERY forum I have read, and I am still getting an I/O error! This is what it reads:
I/O Error!
Device:[1:0:0] PHILIPS DVD+RW-D28 1.29 (D:)
ScsiStatus: 0x02
Interpretation: Check Condition
CDB: 2A 00 00 00 00 00 00 00 10 00
Interpretation: Write (10) Sectors: 0-15
Sense Area: 70 00 05 00 00 00 00 0C 00 00 00 00 2C 00 00 00 00 00
Interpretaton: Command Sequence Error
I 09:24:12 DVD Decrypter Version 3.2.1.0 started!
I 09:24:12 Microsoft Windows XP Home Edition (5.1, Build 2600 : Service Pack 1)
I 09:24:12 Initialising SPTI...
I 09:24:12 Searching for SCSI / ATAPI devices...
I 09:24:12 Found 1 DVD+RW!
I 09:24:39 Operation Started!
I 09:24:39 Source File: C:Documents and SettingsChesney SteffenMy DocumentsMy DVDsBRUCE_ALMIGHTY.ISO
I 09:24:39 Source File Sectors: 2,285,874 (MODE1/2048)
I 09:24:39 Source File Size: 4,681,469,952 bytes
I 09:24:39 Destination Device: [1:0:0] PHILIPS DVD+RW-D28 1.29 (D:)
I 09:24:39 Destination Media Type: Unknown
I 09:24:39 Write Mode: DVD
I 09:24:39 Write Speed: 1x
I 09:24:39 Test Mode: Yes
I 09:24:39 BURN-Proof: Enabled
W 09:24:39 [1:0:0] PHILIPS DVD+RW-D28 1.29 (D:) - Selected Write Speed: 1,385 KB/s (1x)
W 09:24:39 [1:0:0] PHILIPS DVD+RW-D28 1.29 (D:) - Actual Write Speed: 706 KB/s (0.5x)
I 09:24:39 Filling Buffer...
I 09:24:40 Writing LeadIn...
E 09:59:01 Failed to Write Sectors 0 - 15 - Command Sequence Error
I 09:59:01 Synchronising Cache...
I 09:59:01 Cycling Tray after Test Write...
E 09:59:18 Failed to Write Image!
E 09:59:19 Operation Failed! - Duration: 00:34:39
I 09:59:19 Average Write Rate: N/A - Maximum Write Rate: N/A
I am using Memorex DVD-RW...NOT what ScubaPete suggested, but that is what I had before I read to use Ritec (?) or Verbatim. Could this be my problem? Because when I go to "My computer" after inserting the disc into the burner drive, it is not reading the disc. It is showing under DVD Shrink that there is no disc present in that drive. If I reboot my computer and then reinsert disc, it will read it once to try and burn, give me the same I/O error then act as if there is not a disc present!
Or could it be my burner that is the problem? The DVD-RW's that I bought are a 1-2x speed, and I think my burner drive is only a 1x speed. Present on my computer is DVD Shrink, DVD Decryptor and DVD43. I have followed all directions per ScubaPete and the guides on this site so far with the exception of the brand of DVD-RW I'm using. If anyone can help me it would be GREATLY appreciated!!!!
|