|
Something Wrong with the analysis stage !!
|
|
|
shifty01
Suspended due to non-functional email address
|
6. September 2005 @ 04:21 |
Link to this message
|
|
Hey all as the topic says ... its happend twice (with hitch & ladder 49
After i click the "open disk" button it starts then freezes ... i had to reset my PC twice now.
So i downloaded DVD decrypter and im trying it now.
Any comments on similar problems guys & gals ??
|
|
Advertisement
|
|
|
|
AfterDawn Addict
|
6. September 2005 @ 04:32 |
Link to this message
|
|
what is the exact error of the message?
CRC error? those 2 dvds might be a bad pressing or are simply dirty if shrink will not complete the analyzing portion of the encoding...
carefully clean them and see if it will go through...
the exact error you receive would help out here to pinpoint your issue.
Recommended Media:
Taiyo Yuden 4x dvd-r TYGO1/ 8x dvd-r TYGO2/ 8x dvd+r YUDEN000T02/ 16x dvd+r YUDEN000T03
Verbatim 8x dvd+r MCC003
Verbatim dvd+r DL (MKM001)= flawless no compression backups
"Do Yourself A Favor, Use The Good Stuff
TY & Verbs 4 Life~ :)" ~docTY~
"Its better to be quiet and appear stupid, then to open your mouth and remove all doubt."
I am always prepared to recognize that there can be two points of view - mine and one that is probably wrong - John Gorton
|
Member
|
6. September 2005 @ 04:48 |
Link to this message
|
Were you using any type of decrypter with shrink? You can always try AnyDVD for free 21 day trial. Great program!
MS Windows XP MCE SP2, Intel P4 3.20 GHz, 2.0 GB RAM, NVIDIA GeForce FX5600, Seagate 7200 rpm 200GB HDD, Sony SDMHS93 19" LCD, Field Value
Audio Adapter Creative SB0317 Audigy LS Sound Card, Liteon models,SHM-165H6S, 167to6c, All burns exclusively on genuine Taiyo Yuden and Verbatim media!
|
AfterDawn Addict
|
6. September 2005 @ 05:49 |
Link to this message
|
|
|
shifty01
Suspended due to non-functional email address
|
6. September 2005 @ 08:04 |
Link to this message
|
i found the problem ... i followed that link and did all the windows updates .. well its working now.
There must have been some kind of special encryption on the new DVDs ... i used DVD Decrypter then DVD Shrink and everythings fine.
Thx All
|
AfterDawn Addict
|
6. September 2005 @ 08:11 |
Link to this message
|
|
Glad its working for you, Hitch does have ARccOS protection but Ladder 49 has nothing special. But it is better to rip first with Decrypter in file mode to your hard drive and then proceed with Shrink that way you will be sure. Happy burning :)
|
|
shifty01
Suspended due to non-functional email address
|
6. September 2005 @ 08:55 |
Link to this message
|
well ripping it seemed fine but when it starting burning it froze again
any suggestions ??? whats this AnyDVD do ?? iv hear ppl use it in the background to help along or something ?
|
AfterDawn Addict
|
6. September 2005 @ 09:02 |
Link to this message
|
AnyDVD is a driver that works in the background and breaks encryption, it makes the DVD look unprotected to other programs. You still have to use and encoding and burning program with it. Usually CloneDVD, which is by the same distributor works well with AnyDVD. You can try these programs on a 21 day free trial and see if this makes a difference. They are available at
http://www.slysoft.com
Are you still having problems in the encoding stage or the burning? Have you tried using Shrink in re-author mode and doing the movie only?
|
|
shifty01
Suspended due to non-functional email address
|
6. September 2005 @ 20:33 |
Link to this message
|
Quote:
Are you still having problems in the encoding stage or the burning? Have you tried using Shrink in re-author mode and doing the movie only?
The problem now is the burning process ... im guessing im having hardware problems or something. Im gonna take the PC down to the store in the next week or so.
DVD Shrink didnt let me open the ORIGINAL disk up today ... the message said something like "theres no disk in"
|
AfterDawn Addict
|
7. September 2005 @ 04:03 |
Link to this message
|
Try downloading the free 21 day trial version of AnyDVD here:
http://www.afterdawn.com/software/video_software/dvd_rippers/anyd...
With DVD Shrink and DVD Decrypter not being updated anymore,this is a very good background ripper to help the majority of dvd software to rip the newer encryptions.
Download it,turn it on. You'll see a small fox icon in your lower tray.That means it's running. I usually leave it off,until DVD Shrink has a problem with a certain movie.When I turn it on,then shrink takes care of it.Usually sony movies,and sometimes columbia. Very nice program.It also rips off cd encryptions.
Now it's acting up in the burn stage:
What brand name/format/ and speed rate is your blank media?
What brand name/model#/and firmware version on your dvd burner?
What programs are you using in the dvd backup process?
What is your pc specs?
Can you post a burn log?
See if we can't get you going before you take that pc to the shop.
HP a1118x-b/athlon 64-3300+/BenQ 1650 BCDC/LG 8163B/Modded Wii/Epson-R300 and Ty Watershields!!! |
|
Cobrajet
Member
|
7. September 2005 @ 04:07 |
Link to this message
|
|
I too had problems with my PeeCee freezing up during reading and analyzing stage. I had set my Front Side Bus in the bios to a dangerously high amount, and never had any problems with anything until I started using DVDShrink, obviously a CPU intensive program. Once I lowered the speed I burnt 15 discs or more with no problems.
Raymond
|
|
shifty01
Suspended due to non-functional email address
|
7. September 2005 @ 19:34 |
Link to this message
|
Quote:
saugmon (Senior Member) 7. September 2005 @ 08:03
Now it's acting up in the burn stage:
What brand name/format/ and speed rate is your blank media?
What brand name/model#/and firmware version on your dvd burner?
What programs are you using in the dvd backup process?
What is your pc specs?
Can you post a burn log?
The blank DVDs im using are TDK 8x DVD-R (4.7gig)
I got a BEN-Q thats all i know (maybe yous cold tell me how to find the model on my PC through dos commandS ?
The DVD backup process .. atm because SHRINK didnt work i was using Decrypter then using SHRINK to author them.
I got a P4 3.2g / 512 DDR ram / standard audio & video card i think
And i dont know what a burn log is.
Also I neglected to say .. my PCs preformance was very slow (slower than usual)during the burning process. I still think its its a hardware problem because it use to take me 8minutes to burn a DVD now it takes 30min - 45
Quote:
Cobrajet (Newbie) 7. September 2005 @ 08:07
I too had problems with my PeeCee freezing up during reading and analyzing stage. I had set my Front Side Bus in the bios to a dangerously high amount, and never had any problems with anything until I started using DVDShrink, obviously a CPU intensive program. Once I lowered the speed I burnt 15 discs or more with no problems.
Whats a front side bios ?
|
|
Cobrajet
Member
|
7. September 2005 @ 23:42 |
Link to this message
|
|
It's Front Side Bus actually, and basically it's the speed at which the CPU talks to the memory. The faster the better if your system can handle it. Mine could only handle so much. It's settable in the bios upon bootup.
Raymond
|
AfterDawn Addict
|
8. September 2005 @ 03:27 |
Link to this message
|
|
Use that dvd identifier program I posted earlier.It will tell you the exact burner model#.It's a very good free tool.
Since it takes that long to burn,go into device manager and check on the primary and secondary Ide/Atapi controllers. They should be set for Dma or Udma if availabe. Make sure they aren't in pio mode and let us know.
HP a1118x-b/athlon 64-3300+/BenQ 1650 BCDC/LG 8163B/Modded Wii/Epson-R300 and Ty Watershields!!!
|
AfterDawn Addict
|
8. September 2005 @ 04:35 |
Link to this message
|
|
|
konfused1
Member
|
8. September 2005 @ 13:48 |
Link to this message
|
|
Also I neglected to say .. my PCs preformance was very slow (slower than usual)during the burning process. I still think its its a hardware problem because it use to take me 8minutes to burn a DVD now it takes 30min - 45
----------------------------
You might have adware/spyware/virus. Also, it wouldn't hurt to defrag every couple of burns.
|
|
Car.Mike
AfterDawn Addict
|
8. September 2005 @ 15:10 |
Link to this message
|
|
konfused1,
You have to be going into PIO Mode for your burn times to differ that much. Go to Device Manager and look at the secondary IDE Channel and see if DMA is enabled. If not uninstall te sec. IDE Channel by right clicking on it and then re-booting and let the OS re-find that channel.. Also d/l a free registry cleaner and clean the registry of any conflicts. You can google for one
|
|
shifty01
Suspended due to non-functional email address
|
8. September 2005 @ 20:23 |
Link to this message
|
|
|
AfterDawn Addict
|
9. September 2005 @ 05:59 |
Link to this message
|
|
Start out by hi-lighting the top Primary IDE Channel/right click/properties/advanced setting.
This will give you device 0 and device 1. Mine say Ultra dma mode 5 and if available on device 1.
Do the same to the other primary channel and both primary channels.I have Udma 2 on my secondary,and also UDMA if available.
Make sure they don't say pio mode.If they do,click drive tab/uninstall them/reboot/and re-check: 1 channel at a time if more than 1 channel is in pio mode.
If there's a problem,windows will revert your ata/IDE atapi channels to pio mode for safety purposes.
I've got 2 benqs,both 1620 and they do favor the plus format. My plus format backups are booktyped to dvd-rom. I haven't tried any TDK dash format,but I had trouble with the Verbatim -4x.
HP a1118x-b/athlon 64-3300+/BenQ 1650 BCDC/LG 8163B/Modded Wii/Epson-R300 and Ty Watershields!!!
|
|
konfused1
Member
|
9. September 2005 @ 10:17 |
Link to this message
|
|
@Car.Mike
Sorry Car.Mike, I was trying to add my two cents to shifty's problem and copied a part of his/her quote, of course, it didn't come up as such. But thanks for the info nonetheless.
|
|
Car.Mike
AfterDawn Addict
|
9. September 2005 @ 16:05 |
Link to this message
|
|
konfused1,
That's OK
|
|
shifty01
Suspended due to non-functional email address
|
9. September 2005 @ 19:20 |
Link to this message
|
Thanks all for trying to help ...
this is a picture of my PRIMARY 01
this is a picture of my PRIMARY 02
i followed this post
Quote:
saugmon (Senior Member) 9. September 2005 @ 09:59
Start out by hi-lighting the top Primary IDE Channel/right click/properties/advanced setting.
This will give you device 0 and device 1. Mine say Ultra dma mode 5 and if available on device 1.
Do the same to the other primary channel and both primary channels.I have Udma 2 on my secondary,and also UDMA if available.
but im a little confused ... iv put the confusing bits of saugmon in BOLD font.
Should i type in Ultra DMA mode 5 in the"CURRENT TRANSFERR MODE" box ??
heres a picture of my SECONDARY 01
heres a picture of my SECONDARY 02
saugmon theres no UMDA option only UMD and my SECONDARY 02 has a poi should i reomve that ??
Sorry for all the hassle .. i just dont wanna do anything till im sure.
THANKS ALL
|
|
Car.Mike
AfterDawn Addict
|
10. September 2005 @ 03:58 |
Link to this message
|
|
Looks like you have a HD on the primary and a DVD or CD device on the other primary. On the sec.IDE you have the other DVD devices. The one that is in PIO is the one you need to uninstall and let the OS re-install after re-booting. Most if not all HD will be in Ultra DMA mode 5 and the burners or DVD-CD roms will be in DMA 2 or DMA if available. What I do not understand is you should have a yellow flag up next to the secondary IDE Channel when you view Device manager at the start
|
|
shifty01
Suspended due to non-functional email address
|
10. September 2005 @ 09:03 |
Link to this message
|
|
well if it helps .. im running windows xp (home edition)
|
|
Advertisement
|
|
|
|
shifty01
Suspended due to non-functional email address
|
10. September 2005 @ 09:05 |
Link to this message
|
Quote:
Car.Mike
Senior Member
_ 10. September 2005 @ 07:08
On the sec.IDE you have the other DVD devices
Iv only got one DVD device (the dvd burner)
|
