|
|
|
doesn't recognize disk
|
|
|
tripps11
Junior Member
|
30. September 2005 @ 18:18 |
Link to this message
|
|
I have a cd/dvd recorder drive built into to my laptop. I was using it to burn dvd's for a few months with now problems. Now when I put in a burned cd to burn it doesn't even recongize that there is a disk there. I tried cleaning the lens and nothing. anyone have any ideas.
|
|
Advertisement
|
 |
|
|
AfterDawn Addict
|
1. October 2005 @ 00:00 |
Link to this message
|
|
hi
has it read the same BRAND and id codes type discs before????
Nothing here to see, move along folks.
 |
|
tripps11
Junior Member
|
1. October 2005 @ 10:38 |
Link to this message
|
|
Yeah, it burned all types of blank dvd's and cd's a couple of weeks ago. It just started doing this. It also stops has errors when I try burning dvd's. I burned 2-3 hundred before and no problems.
|
AfterDawn Addict
|
1. October 2005 @ 11:04 |
Link to this message
|
|
check you DMA settings in device manager make sure its not gone to PIO mode!
it needs to be DMA mode...
Nothing here to see, move along folks.
|
|
tripps11
Junior Member
|
1. October 2005 @ 11:18 |
Link to this message
|
|
yeah it's in dma mode, what else can I check.
|
AfterDawn Addict
|
1. October 2005 @ 12:01 |
Link to this message
|
|
hi loaded any new apps? like nero incd ???
check your aspi layer and motherbaord chipset drivers get lateset
Nothing here to see, move along folks.
This message has been edited since posting. Last time this message was edited on 1. October 2005 @ 12:02
|
|
tripps11
Junior Member
|
1. October 2005 @ 12:13 |
Link to this message
|
I uninstalled Nero express and then reinstalled it, I deleted incd, looked at firmware updates but it said there weren't any for the brand dvd burner I have. I don't know how to check aspi, or get the motherboard chip drivers. I still not that great working with computers.
|
Moderator
|
1. October 2005 @ 14:48 |
Link to this message
|
sounds like time for proverbial Nero log... post LAST section of your logfile which lives in c:\program files\ahead\nero\nerohistory.log, but DO NOT post your serial number which usually begins with '1A21' or similar
(the logfile is appended to by subsequent burns so the way to identify the sections is via these lines "*** NeroAPI, History File *** ======")
Main PC ~ Intel C2Q Q6600 (G0 Stepping)/Gigabyte GA-EP45-DS3/2GB Crucial Ballistix PC2-8500/Zalman CNPS9700/Antec 900/Corsair HX 620W
Network ~ DD-WRT ~ 2node WDS-WPA2/AES ~ Buffalo WHR-G54S. 3node WPA2/AES ~ WRT54GS v6 (inc. WEP BSSID), WRT54G v2, WRT54G2 v1. *** Forum Rules *** |
|
tripps11
Junior Member
|
1. October 2005 @ 15:05 |
Link to this message
|
|
The problem is that I pluged in an external dvd burner, and have been using that fine, but I still want to use the burner in my laptop to burn cds, but neros history log only shows the logs from the external burner, which were all completed successfully.
|
Moderator
|
1. October 2005 @ 15:14 |
Link to this message
|
|
successful logs are fine, they give a wealth of info, that's usually sufficient to pinpoint the problem(s)
Main PC ~ Intel C2Q Q6600 (G0 Stepping)/Gigabyte GA-EP45-DS3/2GB Crucial Ballistix PC2-8500/Zalman CNPS9700/Antec 900/Corsair HX 620W
Network ~ DD-WRT ~ 2node WDS-WPA2/AES ~ Buffalo WHR-G54S. 3node WPA2/AES ~ WRT54GS v6 (inc. WEP BSSID), WRT54G v2, WRT54G2 v1. *** Forum Rules ***
|
|
tripps11
Junior Member
|
1. October 2005 @ 17:23 |
Link to this message
|
|
But won't the successful log be talking about the other dvd burner, I have two and use the external one burn dvds, and don't use the internal one right now.
|
Moderator
|
2. October 2005 @ 03:47 |
Link to this message
|
|
a i say, it doesn't matter, it'd probably be enough to get you sorted. your choice, all it can do is help you get burning sooner....
Main PC ~ Intel C2Q Q6600 (G0 Stepping)/Gigabyte GA-EP45-DS3/2GB Crucial Ballistix PC2-8500/Zalman CNPS9700/Antec 900/Corsair HX 620W
Network ~ DD-WRT ~ 2node WDS-WPA2/AES ~ Buffalo WHR-G54S. 3node WPA2/AES ~ WRT54GS v6 (inc. WEP BSSID), WRT54G v2, WRT54G2 v1. *** Forum Rules ***
|
|
tripps11
Junior Member
|
2. October 2005 @ 12:48 |
Link to this message
|
okay here is the last log that I have, hope it helps
Windows XP 5.1
IA32
WinAspi: -
ahead WinASPI: File 'C:\Program Files\Ahead\Nero\Wnaspi32.dll': Ver=2.0.1.68, size=160016 bytes, created 7/22/2004 4:33:44 PM
Nero API version: 6.3.1.28
Using interface version: 6.3.1.4
Installed in: C:\Program Files\Ahead\Nero\
Application: ahead\Nero - Burning Rom
Recorder: <HL-DT-ST DVDRAM GSA-5163D>Version: A101 - HA 2 TA 1 - 6.3.1.28
Adapter driver: <> HA 2
Drive buffer : 2048kB
Bus Type : default (0) -> ATAPI, detected: ?
=== Scsi-Device-Map ===
DiskPeripheral : FUJITSU MHT2060AT PL atapi Port 0 ID 0 DMA: On
CdRomPeripheral : PIONEER DVD-RW DVR-K14 atapi Port 1 ID 0 DMA: Off
=== CDRom-Device-Map ===
PIONEER DVD-RW DVR-K14 D: CDRom1
HL-DT-ST DVDRAM GSA-5163 F: CDRom0
=======================
AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 70254592 (0) Byte
ShowDrvBufStat : 0
BUFE : 0
Physical memory : 478MB (489904kB)
Free physical memory: 127MB (130196kB)
Memory in use : 73 %
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)
28.9.2005
NeroAPI
1:44:09 AM #1 Phase 112 File APIProgress.cpp, Line 273
DVD-Video files reallocation started
1:44:09 AM #2 Phase 114 File APIProgress.cpp, Line 273
DVD-Video files reallocation completed (no file modified)
1:44:09 AM #3 Phase 111 File APIProgress.cpp, Line 273
DVD-Video files sorted
1:44:10 AM #4 Text 0 File Reader.cpp, Line 126
Reader running
1:44:10 AM #5 Text 0 File Writer.cpp, Line 124
Writer HL-DT-ST DVDRAM GSA-5163D running
1:44:10 AM #6 Text 0 File AudioCompilationImpl.cpp, Line 817
DRM: StartDrmRecording(RealRec:1, ImageRec:0, Copies:1)
DRM: Beginning burn process.
1:44:10 AM #7 ISO9660GEN -11 File geniso.cpp, Line 3899
First writeable address = 0 (0x00000000)
1:44:10 AM #8 ISO9660GEN -11 File geniso.cpp, Line 3899
First writeable address = 0 (0x00000000)
1:44:10 AM #9 Text 0 File Burncd.cpp, Line 3152
Turn on Disc-At-Once, using DVD media
1:47:01 AM #10 Text 0 File DlgWaitCD.cpp, Line 247
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 2286127 (508:01.52, 4465MB)
1:47:01 AM #11 Text 0 File DlgWaitCD.cpp, Line 259
Write in overburning mode: NO
1:47:01 AM #12 Text 0 File DlgWaitCD.cpp, Line 2161
Recorder: HL-DT-ST DVDRAM GSA-5163D, Media type: DVD-R
Disc Manufacturer: TYG02 -
Disc Application Code: 64, Disc Physical Code: 193
1:47:01 AM #13 Text 0 File DlgWaitCD.cpp, Line 420
>>> Protocol of DlgWaitCD activities: <<<
=========================================
Insert empty disc to write to.
(Medium in drive: unknown. Medium required by compilation: DVD+R/RW, DVD-R/RW, DVD-RAM, DVD+R9 Double Layer.)
1:47:01 AM #14 Text 0 File ThreadedTransferInterface.cpp, Line 813
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 (CTransferItem)
2 indices, index0 (150) not provided
original disc pos #0 + 2286128 (2286128) = #2286128/508:1.53
relocatable, disc pos for caching/writing not required/required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2286128 blocks [HL-DT-ST DVDRAM GSA-5163D]
--------------------------------------------------------------
1:47:01 AM #15 Text 0 File ThreadedTransferInterface.cpp, Line 984
Prepare recorder [HL-DT-ST DVDRAM GSA-5163D] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4681990144, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_RecDep_|_CtrlAdr_
0 | lead-in | 0 | 0x00 | 0x41
0 | 1 | 0 | 0x00 | 0x41
0 | 1 | 1 | 0x00 | 0x41
2286128 | lead-out | 1 | 0x00 | 0x41
1:47:02 AM #16 Phase 24 File APIProgress.cpp, Line 273
Caching of files started
1:47:02 AM #17 Text 0 File Burncd.cpp, Line 4163
Cache writing successful.
1:47:02 AM #18 Phase 25 File APIProgress.cpp, Line 273
Caching of files completed
1:47:02 AM #19 Phase 36 File APIProgress.cpp, Line 273
Burn process started at 4x (5,540 KB/s)
1:47:02 AM #20 Text 0 File ThreadedTransferInterface.cpp, Line 2344
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0
1:47:02 AM #21 Text 0 File DVDR.cpp, Line 2135
Recording mode: Sequential Recording Mode
1:47:02 AM #22 Text 0 File Mmc.cpp, Line 20857
Set BUFE: supported -> ON
1:47:02 AM #23 Text 0 File DVDR.cpp, Line 2276
Start write address at LBA 0
DVD high compatibility mode: Yes
1:47:02 AM #24 Text 0 File Cdrdrv.cpp, Line 8219
---- DVD Structure: Physical Format Information (00h) ----
Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 5
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 26127F h
End Sector Number in Layer 0: 0 h
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 2FE10 h
Start sector number of the next Border-In: 2FFA0 h
Media Specific [16..63]:
00 20 01 02 00 04 00 06 - 00 08 00 00 00 00 00 00 ................
00 02 FE 10 00 02 FF A0 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
1:47:02 AM #25 Text 0 File DVDR.cpp, Line 4795
Drive: HL-DT-ST DVDRAM GSA-5163D
Book Type request: DVD-ROM
Book Type setting not supported for the loaded disc type
1:47:14 AM #26 Text 0 File Cdrdrv.cpp, Line 1296
01:47:14.187 - HL-DT-ST DVDRAM GSA-5163D\H2 T1 : Queue again later
2:01:39 AM #27 Text 0 File WriterStatus.cpp, Line 115
<HL-DT-ST DVDRAM GSA-5163D> start writing Lead-Out at LBA 2286128 (22E230h), lenght 0 blocks
2:01:39 AM #28 Text 0 File ThreadedTransfer.cpp, Line 229
all writers idle, stopping conversion
2:01:39 AM #29 Text 0 File DVDR.cpp, Line 2519
EndDAO: Last written address was 2286127
2:01:57 AM #30 Text 0 File DVDR.cpp, Line 4795
Drive: HL-DT-ST DVDRAM GSA-5163D
Book Type request: DVD+R
Book Type setting not supported for the loaded disc type
2:01:57 AM #31 Phase 37 File APIProgress.cpp, Line 273
Burn process completed successfully at 4x (5,540 KB/s)
2:01:58 AM #32 Text 0 File AudioCompilationImpl.cpp, Line 828
DRM: DRM burn session terminated.
2:01:58 AM #33 Text 0 File AudioCompilationImpl.cpp, Line 857
DRM: Closing entire DRM handling. Bye.
Existing drivers:
File 'Drivers\PXHELP20.SYS': Ver=2.03.12a, size=20576 bytes, created 11/20/2004 3:39:26 AM (Prassi/Veritas driver for win 2K)
Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
[28.09.2005]------------------------------------
01:44:09 Robot error messages from:
====== *** NeroAPI, History File *** ======
|
Moderator
|
2. October 2005 @ 13:01 |
Link to this message
|
@tripps11 -
Quote:
Nero API version: 6.3.1.28
- too old, update to latest, 6.6.0.16
Quote:
Recorder: <HL-DT-ST DVDRAM GSA-5163D>Version: A101
- firmware is outdated, A105 is here - http://forum.rpc1.org/dl_firmware.php?download_id=2036
Quote:
Bus Type : default (0) -> ATAPI, detected: ?
- i can see this is the external burner you were talking about so that question mark is fine
Quote:
DiskPeripheral : FUJITSU MHT2060AT PL atapi Port 0 ID 0 DMA: On
CdRomPeripheral : PIONEER DVD-RW DVR-K14 atapi Port 1 ID 0 DMA: Off
- DMA needs to be ON, fix it via this - http://home.comcast.net/~bbmayo/FAQ.htm
Quote:
Physical memory : 478MB (489904kB)
Free physical memory: 127MB (130196kB)
Memory in use : 73 %
- make sure to close down more programs prior to all burns to free up more memory
Quote:
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 2286127 (508:01.52, 4465MB)
- you're burning to outer edge of discs, if you use DVD Shrink, set target size in Shrink's preferences to 4300MB, thus avoiding outer edge and not sacrificing much space
Quote:
Recorder: HL-DT-ST DVDRAM GSA-5163D, Media type: DVD-R
Disc Manufacturer: TYG02 -
Disc Application Code: 64, Disc Physical Code: 193
- hmmm, i wonder if those are genuine TY discs, TYG02 are faked a helluva lot
Quote:
Insert empty disc to write to.
(Medium in drive: unknown. Medium required by compilation: DVD+R/RW, DVD-R/RW, DVD-RAM, DVD+R9 Double Layer.)
- you need to make sure blank discs are in the drive BEFORE startig burning to allow Nero to detect the available speeds of the disc
Quote:
Drive: HL-DT-ST DVDRAM GSA-5163D
Book Type request: DVD-ROM
Book Type setting not supported for the loaded disc type
- you can't 'booktype' -R discs, only +R discs. change the booktype setting to auto in Nero/Recorder/Choose Recorder/Options
Quote:
Burn process completed successfully at 4x (5,540 KB/s)
- 4x is what most people recommend for movie burns
Quote:
Existing drivers:
- no mention of atapi drivers here, this should be resolved by following the DMA fix further up the reply..
Main PC ~ Intel C2Q Q6600 (G0 Stepping)/Gigabyte GA-EP45-DS3/2GB Crucial Ballistix PC2-8500/Zalman CNPS9700/Antec 900/Corsair HX 620W
Network ~ DD-WRT ~ 2node WDS-WPA2/AES ~ Buffalo WHR-G54S. 3node WPA2/AES ~ WRT54GS v6 (inc. WEP BSSID), WRT54G v2, WRT54G2 v1. *** Forum Rules ***
|
|
tripps11
Junior Member
|
2. October 2005 @ 14:05 |
Link to this message
|
|
Thanks, i'll try all that
|
|
tripps11
Junior Member
|
3. October 2005 @ 22:34 |
Link to this message
|
|
The page for the firmware update is temporarily down, is there any other sites I can get the same upgrade from? I did everything else and my drive still won't read disks, so I am hoping that the firmware is the problem.
|
AfterDawn Addict
|
3. October 2005 @ 22:45 |
Link to this message
|
Nothing here to see, move along folks.
|
|
Advertisement
|
|
|
|
tripps11
Junior Member
|
6. October 2005 @ 10:54 |
Link to this message
|
|
I was wondering, is the firmware different for my external burner than it would be for my internal one, and if so will updating the firmware for my external burner help any problems with my internal one? also what are cyclical redudancy errors, and how can I get around them?
|
|
