|
|
|
ScanDisc errors with Nero DVD speed after buring
|
|
|
ChikaraNZ
Junior Member
|
14. October 2005 @ 18:07 |
Link to this message
|
|
Hi all,
I've recently got into the world of DVD back-ups. I've got lots of wonderful advice from these forums, so thank you all (esp. ScubaPete - very informative and helpful posts!)
I can rip and burn seemingly sucessfully. After the burn I make sure the verify data option is on. I have also been doing a ScanDisc with Nero DriveSpeed straight after, and that has been confirming 100% good sectors.
However - I am having some problems.
I've noticed that for many discs, when I do a ScanDisc say a week or so later, it then picks up either damaged or bad sectors. In some cases I haven't used the DVD *at all* in the meantime
Why would this be? How is it possible for a DVD to scan 100%, and then the very next time scan with damaged sectors, when it hasn't even been played or touched in the meantime?
The only thing I can think of is the dye must be changing after it's been written, however with the MCC discs I'm using I thought they were one of the bext qiality ones?
Or is it just Nero DriveSpeed being tempramental?
I use DVDShrink 3.2, (DVD Decrypter 3.5.4 if needed first), and burn seperately with Nero. I have Nero 6.6.0.15.
I always make sure all other applications are closed down before I burn, and burn using 2x speed (have had same problems on 4x speeds too). I'm using a Plextor 712A with the latest firmware. The current DVD's Im using are Mitsubishi brand, manufactured by MCC which I understand are a excellent brand. (I used to use Imation ((CMC(before I realised how crappy they were after reading the forums!). Running WinXP.
Any help or comments would be appreciated.
Have a great day!
Tony
|
|
Advertisement
|
|
|
|
Moderator
|
26. October 2005 @ 11:42 |
Link to this message
|
Hi, welcome. looks like your thread got missed, hence you started that new thread. i've requested that one be closed and will help you out here (as probably will others too now as this thread will be on the first page of the forum as it's been replied to)....
let's have LAST section of your Nero log which lives in c:\program files\ahead\nero\nerohistory.log but DO NOT post your serial number which usually begins with '1A21' or similar. You can differentiate sections via this section divider "====== *** Nero-Burning Rom, History File *** ======"
Main PC ~ Intel C2Q Q6600 (G0 Stepping)/Gigabyte GA-EP45-DS3/2GB Crucial Ballistix PC2-8500/Zalman CNPS9700/Antec 900/Corsair HX 620W
Network ~ DD-WRT ~ 2node WDS-WPA2/AES ~ Buffalo WHR-G54S. 3node WPA2/AES ~ WRT54GS v6 (inc. WEP BSSID), WRT54G v2, WRT54G2 v1. *** Forum Rules *** |
|
ChikaraNZ
Junior Member
|
30. October 2005 @ 09:43 |
Link to this message
|
Hi Creaky, thanks for the reply.
Here is the error log (below) - hopefully i've included the right bits.
This is an error log from my most recent backup. Although I haven't done a scandisc on this particular burn yet, I am using the same brand of media and haven't changed any settings.
Thanks!
Windows XP 5.1
IA32
WinAspi: -
ahead WinASPI: File 'C:\Program Files\Ahead\nero\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 26/10/2004 7:35:34 p.m.
Nero Version: 6.6.0.15
Internal Version: 6, 6, 0, 15h
Recorder: <PLEXTOR DVDR PX-712A> Version: 1.07 - HA 1 TA 0 - 6.6.0.15
Adapter driver: <atapi> HA 1
Drive buffer : 8192kB
Bus Type : default (0) -> ATAPI, detected: ATAPI
CD-ROM: <PLEXTOR DVDR PX-712A >Version: 1.07 - HA 1 TA 0 - 6.6.0.15
Adapter driver: <atapi> HA 1
=== Scsi-Device-Map ===
DiskPeripheral : ST3120026A atapi Port 0 ID 0 DMA: On
CdRomPeripheral : PLEXTOR DVDR PX-712A atapi Port 1 ID 0 DMA: Off
CdRomPeripheral : E-IDE CD-ROM 52X/AKH atapi Port 1 ID 1 DMA: Off
CdRomPeripheral : SCSIVAX DVD/CD-ROM 2.7a vax347s Port 2 ID 0 DMA: Off
=== CDRom-Device-Map ===
PLEXTOR DVDR PX-712A D: CDRom0
E-IDE CD-ROM 52X/AKH E: CDRom1
SCSIVAX DVD/CD-ROM F: CDRom2
=======================
AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 74448896 (0) Byte
ShowDrvBufStat : 0
BUFE : 0
Physical memory : 511MB (523744kB)
Free physical memory: 208MB (213072kB)
Memory in use : 59
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)
26.10.2005
UDF/ISO compilation
5:43:41 p.m. #1 Phase 112 File dlgbrnst.cpp, Line 1832
DVD-Video files reallocation started
5:43:41 p.m. #2 Phase 114 File dlgbrnst.cpp, Line 1832
DVD-Video files reallocation completed (no file modified)
5:43:41 p.m. #3 Text 0 File Isodoc.cpp, Line 6314
Iso document burn settings
------------------------------------------
Determine maximum speed : FALSE
Simulate : FALSE
Write : TRUE
Finalize CD : TRUE
Multisession : FALSE
Burning mode : DAO
Mode : 1
ISO Level : 1 (Max. of 11 = 8 + 3 char)
Character set : ISO 9660
Joliet :FALSE
Allow pathdepth more than 8 directories : FALSE
Allow more than 255 characters in path : FALSE
Write ISO9660 ;1 file extensions : TRUE
5:43:41 p.m. #4 Phase 111 File dlgbrnst.cpp, Line 1832
DVD-Video files sorted
5:43:42 p.m. #5 Text 0 File Reader.cpp, Line 127
Reader running
5:43:42 p.m. #6 Text 0 File Writer.cpp, Line 122
Writer PLEXTOR DVDR PX-712A running
5:43:42 p.m. #7 ISO9660GEN -11 File geniso.cpp, Line 3309
First writeable address = 0 (0x00000000)
5:43:42 p.m. #8 ISO9660GEN -11 File geniso.cpp, Line 3309
First writeable address = 0 (0x00000000)
5:43:42 p.m. #9 Text 0 File Burncd.cpp, Line 3231
Turn on Disc-At-Once, using DVD media
5:43:42 p.m. #10 Text 0 File DlgWaitCD.cpp, Line 269
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 2286127 (508:01.52, 4465MB)
5:43:42 p.m. #11 Text 0 File DlgWaitCD.cpp, Line 281
Write in overburning mode: NO (enabled: CD)
5:43:42 p.m. #12 Text 0 File DlgWaitCD.cpp, Line 2477
Recorder: PLEXTOR DVDR PX-712A, Media type: DVD-R
Disc Manufacturer: MCC 02 - RG20
Disc Application Code: 64, Disc Physical Code: 193
5:43:42 p.m. #13 Text 0 File DlgWaitCD.cpp, Line 447
>>> Protocol of DlgWaitCD activities: <<<
=========================================
5:43:42 p.m. #14 Text 0 File ThreadedTransferInterface.cpp, Line 830
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
2 indices, index0 (150) not provided
original disc pos #0 + 2286128 (2286128) = #2286128/508:1.53
relocatable, disc pos for caching/writing not required/ required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2286128 blocks [PLEXTOR DVDR PX-712A]
--------------------------------------------------------------
5:43:42 p.m. #15 Text 0 File ThreadedTransferInterface.cpp, Line 1043
Prepare recorder [PLEXTOR DVDR PX-712A] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4681990144, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
2286128 | lead-out | 1 | 0x41 | 0x00
5:43:42 p.m. #16 Phase 24 File dlgbrnst.cpp, Line 1832
Caching of files started
5:43:42 p.m. #17 Text 0 File Burncd.cpp, Line 4116
Cache writing successful.
5:43:42 p.m. #18 Phase 25 File dlgbrnst.cpp, Line 1832
Caching of files completed
5:43:42 p.m. #19 Phase 65 File dlgbrnst.cpp, Line 1832
Burn process started
5:43:42 p.m. #20 Text 0 File ThreadedTransferInterface.cpp, Line 2643
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0
5:43:42 p.m. #21 Text 0 File DVDR.cpp, Line 2357
Recording mode: Sequential Recording Mode
5:43:42 p.m. #22 Text 0 File Mmc.cpp, Line 21663
Set BUFE: BURN-Proof -> ON
5:43:42 p.m. #23 Text 0 File DVDR.cpp, Line 2511
Start write address at LBA 0
DVD high compatibility mode: Yes
5:43:42 p.m. #24 Text 0 File Cdrdrv.cpp, Line 8821
---- DVD Structure: Physical Format Information (00h) ----
Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 5
Disc Size: 120 mm, Maximum Rate: 10.08 Mbps (2 h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 26127F h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 0 h
Start sector number of the next Border-In: 0 h
Media Specific [16..63]:
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
5:43:44 p.m. #25 Text 0 File Cdrdrv.cpp, Line 1288
17:43:44.837 - PLEXTOR DVDR PX-712A\H1 T0 : Queue again later
5:44:24 p.m. #26 Text 0 File Cdrdrv.cpp, Line 1288
17:44:24.844 - PLEXTOR DVDR PX-712A\H1 T0 : Queue again later
6:30:47 p.m. #27 Text 0 File WriterStatus.cpp, Line 116
<PLEXTOR DVDR PX-712A > start writing Lead-Out at LBA 2286128 (22E230h), lenght 0 blocks
6:30:47 p.m. #28 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion
6:30:47 p.m. #29 Text 0 File DVDR.cpp, Line 2749
EndDAO: Last written address was 2286127
6:31:33 p.m. #30 Phase 66 File dlgbrnst.cpp, Line 1832
Burn process completed successfully
6:31:33 p.m. #31 Phase 78 File dlgbrnst.cpp, Line 1832
Data verification started
7:31:50 p.m. #32 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion
7:31:50 p.m. #33 Phase 80 File dlgbrnst.cpp, Line 1832
Data verification completed successfully
Existing drivers:
File 'Drivers\atapi.sys': Ver=5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), size=95360 bytes, created 3/08/2004 10:59:44 p.m. (Adapter driver for rec)
Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
|
Moderator
|
30. October 2005 @ 10:19 |
Link to this message
|
very odd, it doesn't show what burn speed you used. ah well, here goes...
Quote:
DiskPeripheral : ST3120026A atapi Port 0 ID 0 DMA: On
CdRomPeripheral : PLEXTOR DVDR PX-712A atapi Port 1 ID 0 DMA: Off
CdRomPeripheral : E-IDE CD-ROM 52X/AKH atapi Port 1 ID 1 DMA: Off
CdRomPeripheral : SCSIVAX DVD/CD-ROM 2.7a vax347s Port 2 ID 0 DMA: Off
- a-ha, DMA needs to be ON, fix it via this - http://home.comcast.net/~bbmayo/FAQ.htm
Quote:
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 2286127 (508:01.52, 4465MB)
- even though those MCC discs are real nice, you're burning too close to outer edge of discs. If you use DVD Shrink, set target size to 4300MB in Shrink's preferences thus avoiding outer edge and not sacrificing much space. I only use top notch discs and i swear by 4300MB
Quote:
Recorder: PLEXTOR DVDR PX-712A, Media type: DVD-R
Disc Manufacturer: MCC 02 - RG20
Disc Application Code: 64, Disc Physical Code: 193
- as i say, very nice discs
Quote:
Burn process completed successfully
Data verification completed successfully
- looks good..
Main PC ~ Intel C2Q Q6600 (G0 Stepping)/Gigabyte GA-EP45-DS3/2GB Crucial Ballistix PC2-8500/Zalman CNPS9700/Antec 900/Corsair HX 620W
Network ~ DD-WRT ~ 2node WDS-WPA2/AES ~ Buffalo WHR-G54S. 3node WPA2/AES ~ WRT54GS v6 (inc. WEP BSSID), WRT54G v2, WRT54G2 v1. *** Forum Rules ***
|
Senior Member
|
30. October 2005 @ 12:27 |
Link to this message
|
Your Nero version is also 1 version behind, current version is 6.6.0.16, but I doubt that has anything to do with it.
|
|
ChikaraNZ
Junior Member
|
5. November 2005 @ 06:39 |
Link to this message
|
Thanks for that. I do have DMA enabled, and have checked that previously. But even though that option is set, it seems for some reason when Nero burns, according to the log, it doesn't use that?
Is there any setting within Nero that might over-ride the Windows setting?
Thanks for the tip about the target size I will try that.
BTW - I am burning at 2x, weird the log doesnt show that.
|
Moderator
|
5. November 2005 @ 06:45 |
Link to this message
|
|
ok let's have the LATEST log entry then, to see what's what...
Main PC ~ Intel C2Q Q6600 (G0 Stepping)/Gigabyte GA-EP45-DS3/2GB Crucial Ballistix PC2-8500/Zalman CNPS9700/Antec 900/Corsair HX 620W
Network ~ DD-WRT ~ 2node WDS-WPA2/AES ~ Buffalo WHR-G54S. 3node WPA2/AES ~ WRT54GS v6 (inc. WEP BSSID), WRT54G v2, WRT54G2 v1. *** Forum Rules ***
|
|
ChikaraNZ
Junior Member
|
9. November 2005 @ 23:11 |
Link to this message
|
|
I haven't done any burns since my first post, so the log above is still the most recent one. Is there more bits to the log you would need to see?
I've been having a sniff around the internet for info as well, and have read that Windows can automatically disable DMA (and it can't be changed back unless you uninstall/reinstall the drive) if it gets a lot of errors from the drive concerned. Could that be the cause in my case? I'm not sure how to check if that's the fault.
In any case, shouldn't I still be able to burn correctly when DMA is off? (albeit slower?)
|
Moderator
|
9. November 2005 @ 23:32 |
Link to this message
|
|
no you need to fix your DMA settings as described..
then if you realy want to, you could do a 'simulation burn' which goes thru the motions with a blank disc but doesn't actually write to it but will append a log entry to the logfile which you can check the DMA..
Main PC ~ Intel C2Q Q6600 (G0 Stepping)/Gigabyte GA-EP45-DS3/2GB Crucial Ballistix PC2-8500/Zalman CNPS9700/Antec 900/Corsair HX 620W
Network ~ DD-WRT ~ 2node WDS-WPA2/AES ~ Buffalo WHR-G54S. 3node WPA2/AES ~ WRT54GS v6 (inc. WEP BSSID), WRT54G v2, WRT54G2 v1. *** Forum Rules ***
|
|
ChikaraNZ
Junior Member
|
10. November 2005 @ 23:11 |
Link to this message
|
|
OK, uninstalling and then reinstalling the drive was the only way I could get DMA working.
I'll try another burn over the weekend and let you know how I get on.
|
|
ChikaraNZ
Junior Member
|
16. November 2005 @ 09:52 |
Link to this message
|
Well I tried anotehr burn over the weekend and it seems sucessful. Log is below.
What I don't understand though still is - even with DMA disabled in my earlier attempts, how could a scandisc show 100% correct initially, and then later on give errors?
Windows XP 5.1
IA32
WinAspi: -
ahead WinASPI: File 'C:\Program Files\Ahead\nero\Wnaspi32.dll':
Ver=2.0.1.74, size=164112 bytes, created 26/10/2004 7:35:34 p.m.
Nero Version: 6.6.0.15
Internal Version: 6, 6, 0, 15h
Recorder: <PLEXTOR DVDR PX-712A> Version: 1.07 - HA 1 TA 0 -
6.6.0.15
Adapter driver: <atapi> HA 1
Drive buffer : 8192kB
Bus Type : default (0) -> ATAPI, detected: ATAPI
CD-ROM: <PLEXTOR DVDR PX-712A >Version: 1.07 - HA 1 TA 0 -
6.6.0.15
Adapter driver: <atapi> HA 1
=== Scsi-Device-Map ===
DiskPeripheral : ST3120026A atapi Port 0 ID 0
DMA: On
CdRomPeripheral : PLEXTOR DVDR PX-712A atapi Port 1 ID 0
DMA: On
CdRomPeripheral : E-IDE CD-ROM 52X/AKH atapi Port 1 ID 1
DMA: On
=== CDRom-Device-Map ===
PLEXTOR DVDR PX-712A D: CDRom0
E-IDE CD-ROM 52X/AKH E: CDRom1
=======================
AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 74448896 (0) Byte
ShowDrvBufStat : 0
BUFE : 0
Physical memory : 511MB (523744kB)
Free physical memory: 236MB (241936kB)
Memory in use : 53
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)
13.11.2005
UDF/ISO compilation
7:13:50 p.m. #1 Phase 112 File dlgbrnst.cpp, Line 1832
DVD-Video files reallocation started
7:13:50 p.m. #2 Phase 114 File dlgbrnst.cpp, Line 1832
DVD-Video files reallocation completed (no file modified)
7:13:50 p.m. #3 Text 0 File Isodoc.cpp, Line 6314
Iso document burn settings
------------------------------------------
Determine maximum speed : FALSE
Simulate : FALSE
Write : TRUE
Finalize CD : TRUE
Multisession : FALSE
Burning mode : DAO
Mode : 1
ISO Level : 1 (Max. of 11 = 8 + 3 char)
Character set : ISO 9660
Joliet :FALSE
Allow pathdepth more than 8 directories : FALSE
Allow more than 255 characters in path : FALSE
Write ISO9660 ;1 file extensions : TRUE
7:13:50 p.m. #4 Phase 111 File dlgbrnst.cpp, Line 1832
DVD-Video files sorted
7:13:50 p.m. #5 Text 0 File Reader.cpp, Line 127
Reader running
7:13:50 p.m. #6 Text 0 File Writer.cpp, Line 122
Writer PLEXTOR DVDR PX-712A running
7:13:50 p.m. #7 ISO9660GEN -11 File geniso.cpp, Line 3309
First writeable address = 0 (0x00000000)
7:13:50 p.m. #8 ISO9660GEN -11 File geniso.cpp, Line 3309
First writeable address = 0 (0x00000000)
7:13:50 p.m. #9 Text 0 File Burncd.cpp, Line 3231
Turn on Disc-At-Once, using DVD media
7:13:50 p.m. #10 Text 0 File DlgWaitCD.cpp, Line 269
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 2202159 (489:22.09, 4301MB)
7:13:50 p.m. #11 Text 0 File DlgWaitCD.cpp, Line 281
Write in overburning mode: NO (enabled: CD)
7:13:50 p.m. #12 Text 0 File DlgWaitCD.cpp, Line 2477
Recorder: PLEXTOR DVDR PX-712A, Media type: DVD-R
Disc Manufacturer: MCC 02 - RG20
Disc Application Code: 64, Disc Physical Code: 193
7:13:50 p.m. #13 Text 0 File DlgWaitCD.cpp, Line 447
>>> Protocol of DlgWaitCD activities: <<<
=========================================
7:13:50 p.m. #14 Text 0 File ThreadedTransferInterface.cpp, Line 830
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
2 indices, index0 (150) not provided
original disc pos #0 + 2202160 (2202160) = #2202160/489:22.10
relocatable, disc pos for caching/writing not required/ required, no
patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length
2202160 blocks [PLEXTOR DVDR PX-712A]
--------------------------------------------------------------
7:13:50 p.m. #15 Text 0 File ThreadedTransferInterface.cpp, Line 1043
Prepare recorder [PLEXTOR DVDR PX-712A] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0
4510023680, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
2202160 | lead-out | 1 | 0x41 | 0x00
7:13:50 p.m. #16 Phase 24 File dlgbrnst.cpp, Line 1832
Caching of files started
7:13:50 p.m. #17 Text 0 File Burncd.cpp, Line 4116
Cache writing successful.
7:13:50 p.m. #18 Phase 25 File dlgbrnst.cpp, Line 1832
Caching of files completed
7:13:50 p.m. #19 Phase 65 File dlgbrnst.cpp, Line 1832
Burn process started
7:13:50 p.m. #20 Text 0 File ThreadedTransferInterface.cpp, Line 2643
Verifying disc position of item 0 (relocatable, disc pos, no patch infos,
orig at #0): write at #0
7:13:50 p.m. #21 Text 0 File DVDR.cpp, Line 2357
Recording mode: Sequential Recording Mode
7:13:50 p.m. #22 Text 0 File Mmc.cpp, Line 21663
Set BUFE: BURN-Proof -> ON
7:13:50 p.m. #23 Text 0 File DVDR.cpp, Line 2511
Start write address at LBA 0
DVD high compatibility mode: Yes
7:13:50 p.m. #24 Text 0 File Cdrdrv.cpp, Line 8821
---- DVD Structure: Physical Format Information (00h) ----
Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 5
Disc Size: 120 mm, Maximum Rate: 10.08 Mbps (2 h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer
Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW,
DVD+R/+RW)
End Physical Sector Number of Data Area: 26127F h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h,
4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 0 h
Start sector number of the next Border-In: 0 h
Media Specific [16..63]:
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
7:13:52 p.m. #25 Text 0 File Cdrdrv.cpp, Line 1288
19:13:52.752 - PLEXTOR DVDR PX-712A\H1 T0 : Queue again later
7:14:32 p.m. #26 Text 0 File Cdrdrv.cpp, Line 1288
19:14:32.749 - PLEXTOR DVDR PX-712A\H1 T0 : Queue again later
7:41:37 p.m. #27 Text 0 File WriterStatus.cpp, Line 116
<PLEXTOR DVDR PX-712A > start writing Lead-Out at LBA 2202160
(219A30h), lenght 0 blocks
7:41:37 p.m. #28 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion
7:41:37 p.m. #29 Text 0 File DVDR.cpp, Line 2749
EndDAO: Last written address was 2202159
7:42:49 p.m. #30 Phase 66 File dlgbrnst.cpp, Line 1832
Burn process completed successfully
7:42:49 p.m. #31 Phase 78 File dlgbrnst.cpp, Line 1832
Data verification started
7:49:22 p.m. #32 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion
7:49:22 p.m. #33 Phase 80 File dlgbrnst.cpp, Line 1832
Data verification completed successfully
Existing drivers:
File 'Drivers\atapi.sys': Ver=5.1.2600.2180 (xpsp_sp2_rtm.040803-2158),
size=95360 bytes, created 3/08/2004 10:59:44 p.m. (Adapter driver for rec)
Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs :
0 (Security Option)
|
Senior Member
|
16. November 2005 @ 14:41 |
Link to this message
|
The only thing I could find wrong w/ it is that your Nero is out of date, current version is 6.6.0.18.
And you might also want to not multitask while burning.
|
|
Advertisement
|
|
|
|
ChikaraNZ
Junior Member
|
18. November 2005 @ 11:16 |
Link to this message
|
Thanks for that. I do always make so no other apps are running when I'm burning and don't even touch the computer during that time.
I might try getting the latest Nero to see if that makes a difference.
Could it be that there was some some of error with the dye on the discs? And that is why initial scandiscs show 100%, but subsequent ones weeks later show errors - that the dye has somehow deteriorated over the days/weeks after burning?
Because if there was an error during the initial burn, surely the initial scandisc would have shown errors?
|
|
