|
DVD stops during analysing/encoding
|
|
|
Mark_2112
Newbie
|
18. July 2006 @ 08:43 |
Link to this message
|
|
I hope I am posting in the right subject here goes. When I run dvd-shrink the dvd drive just stops during analysing and if I get past that it will stop about 75% or more during the encoding. It used to work just fine been using it for over a year. I've tried different discs and tried using dvd decripter as well and the same thing happens just stops about 3/4 of the way done. I have a DVD burner and DVD rom in my computer both drives act the same way. I used the burner to burn a DVD a few days ago and all is fine just seems now to just stop during a read. Any suggestions anybody ? Thanks !
|
|
Advertisement
|
 |
|
|
|
pazzini
Suspended permanently
|
18. July 2006 @ 08:50 |
Link to this message
|
|
Member
|
18. July 2006 @ 08:58 |
Link to this message
|
|
make sure someone you live with isnt sabotaging your shrink sessions lol you know like clicking the red x when you are not looking ..anyway this is very unusual ..need more input
|
|
Mark_2112
Newbie
|
18. July 2006 @ 09:09 |
Link to this message
|
Now that I know I have a problem..any movie. I've tried ones I've burned, and prerecorded orginials I have..all act the same way. I've tried to use DVD-Decrypter as well as Nero to copy any dvd..and it just stops 3/4 of the way..no error messages..computer still responds it doesnt lock it up and it acts this way in both drives...
|
|
pazzini
Suspended permanently
|
18. July 2006 @ 11:26 |
Link to this message
|
|
|
Mark_2112
Newbie
|
18. July 2006 @ 12:22 |
Link to this message
|
|
I may try some of these other software solutions but I've already tried three different ones I have on both of my drives with the same results. What I don't understand that it used to work slick as a whistle no problems..until now and I don't what has happened to cause this as I have not copied any DVD's in a while until I tried two days ago. The computer is a P4 with 250GB drive 512M mem with a NEC DVD burner and a Samsung DVD Rom from Gateway about a year and half old and I am really selective about installing software on it and I checked for virus adware malware etc and all is clean...
|
|
Mark_2112
Newbie
|
18. July 2006 @ 17:20 |
Link to this message
|
|
To amend my last post..I tested by burning a DVD I dowloaded..4 times worked flawlessly..but still freezes during a read !?
|
|
Mark_2112
Newbie
|
19. July 2006 @ 06:14 |
Link to this message
|
|
I tried it again this time I got a error message "error reading drive E:\ redundancy cycle, again about 3/4 of the way through the encoding..anybody have any idea's? Burning is no problem but a read is.
|
|
leia176
Junior Member
|
19. July 2006 @ 06:41 |
Link to this message
|
|
Try uninstalling and reinstalling?
Could your DVD drive be going? Probably not, but something to think about.
|
AfterDawn Addict
|
19. July 2006 @ 07:09 |
Link to this message
|
|
|
Mark_2112
Newbie
|
19. July 2006 @ 08:53 |
Link to this message
|
|
I've checked on DMA it is showing as active..and if it is the drive cable why can I burn from the drives fine but stall during a read?
|
Senior Member
|
19. July 2006 @ 17:21 |
Link to this message
|
|
@ Mark_2112,
hey, so r u getting that error only on the same disk or u r getting that error while using different disks?
also what movie r u trying to rip?
Is the movie dirty or scracthed?
Also did u try DVDFab decrypter? if not this is a good ripper for dirty or scracthed disks, that error is usually a scrachted disk or a new protection
U can get DVDFab in pazzini's post
"When I look at the smiles on all the childrens faces, I just know theyre about to jab me with something."- Homer Simpson |
|
Mark_2112
Newbie
|
20. July 2006 @ 04:03 |
Link to this message
|
|
tried several different discs all of them I've burned in the sae drive and tried from both drives including pre recorded discs get the same error but I can burn flawlessly.
|
AfterDawn Addict
|
20. July 2006 @ 04:25 |
Link to this message
|
|
Only thing I can tell you is to try blowing some canned air into the drive, it may be some dirt that is in there. How old is this burner anyway?
|
|
Mark_2112
Newbie
|
20. July 2006 @ 05:43 |
Link to this message
|
|
I've done that..the drive(s) are about 1 1/2 yrs old..complete system from Gateway..
|
AfterDawn Addict
|
20. July 2006 @ 05:56 |
Link to this message
|
|
And this is on both drives, the reader and the burner?
Edit: Have you put in any new sw, any sw or OS updates recently?
This message has been edited since posting. Last time this message was edited on 20. July 2006 @ 05:59
|
|
Mark_2112
Newbie
|
20. July 2006 @ 07:25 |
Link to this message
|
|
Yes both drives burner and dvd rom. No updates other that MS criticals for XP (I have media edition) as far as software just itunes lately that came with my ipod
|
AfterDawn Addict
|
20. July 2006 @ 07:28 |
Link to this message
|
|
Have you tried a system restore to back before you had the problems. It is unusual for both drives to crap at the same time with the sam problem. Got to be some conflict somewhere.
|
|
Mark_2112
Newbie
|
20. July 2006 @ 09:15 |
Link to this message
|
|
No I haven't tried to do that..I really don't know how far to go back because it had been a few months since I last ripped a DVD
|
|
Advertisement
|
|
|
|
Mark_2112
Newbie
|
20. July 2006 @ 18:08 |
Link to this message
|
I had some sucess. I got one of them ripped that I had been trying to copy...finally. I used DVD Decrytper and ripped it as a ISO changing the settings I saw for DVD Decrypter in another post in this forum posted by ScubaPete. Thanks everybody this is a great forum !
|
