Mobile/PDA About Us Advertise here
User User name Password  
  Not registered yet? Register here.
Lost your password? Click here. 		 
  Home   News   Guides   Downloads   Glossary   Hardware   Profiles   Forums   v4  
 Advertise at AfterDawn.com     Link to us!     Private messages     Compose a private message     List of all updated threads     Threads without replies     Search messages
Sunday 27.7.2025 / 05:56
Search AfterDawn Forums:        In English   Suomeksi   På svenska
afterdawn.com > forums > archived forums > xbox - general discussion > xecutre 2.2 lite plus
Show topics
 
Forums
Forums
Xecutre 2.2 Lite Plus
  Jump to:
 
Posted Message
cheech65
Newbie
_ 		13. September 2003 @ 00:14 _ Link to this message    Send private message to this user   
I just got my chip, and tried to install it in my box. I got the two blue LEDs to light, but no matter what I tried I could not get the green LED to come on and get to the screen that would allow me to flash the BIOS. If anyone out there has run into similar problems, please let me know how you resolved them. It is a version 1.0 box. However, I tried installing the chip with the switch in both positions.
[ + quote]
Advertisement
_ 		__
strobbe
Newbie
_ 		13. September 2003 @ 08:15 _ Link to this message    Send private message to this user   
Do all the pins connect to the Do points because that is what happened to me.
You can see that the pins though all the Do points by looking for scratches on the Do points.
[ + quote]
djc11369
Junior Member
_ 		14. September 2003 @ 09:34 _ Link to this message    Send private message to this user   
There seems to be an alignment issue with the x2lite+. I got mine from the-console-corner and have read other posts on here that have had the same problem. I had to drill out (very slowly) the hole larger in the x2 board to get the d0 pin to align. After tightening it down and got the light to come on I put hot glue around the screw and board on top and on the opposite side of the board where there were no traces or components to help keep it from moving. Hope this helps.
[ + quote]
cheech65
Newbie
_ 		14. September 2003 @ 11:15 _ Link to this message    Send private message to this user   
After a few hours of work, I got the chip in the right way. Finally, I just happened to put it in the right way and got everything to come on. Now, I get no picture on the TV when I turn the chip on. If anyone else had a similar problem, please share how it was resolved.
[ + quote]
Ninjak
Newbie
_ 		29. September 2003 @ 21:29 _ Link to this message    Send private message to this user   
cheech, according to some instructions i found on the-console-corner when the blank screen happened to me, just turn off the xbox, switch the chip to disable, turn on the xbox in "normal" mode for 15 seconds, turn off, enable the chip, then turn it on again. Worked for me when i tried it.
[ + quote]
Advertisement
_ 		__
 
_
Lowride66
Suspended due to non-functional email address
_ 		30. September 2003 @ 03:19 _ Link to this message    Send private message to this user   
The Lite chip comes with Cromwell on it, and it doesn't work with S-video if thats whats your using. Get rid of the Cromwell and the S-vid is fine.
[ + quote]
afterdawn.com > forums > archived forums > xbox - general discussion > xecutre 2.2 lite plus
 

Digital video: AfterDawn.com | AfterDawn Forums
Music: MP3Lizard.com
Gaming: Blasteroids.com | Blasteroids Forums | Compare game prices
Software: Software downloads
Blogs: User profile pages
RSS feeds: AfterDawn.com News | Software updates | AfterDawn Forums
International: AfterDawn in Finnish | AfterDawn in Swedish | AfterDawn in Norwegian | download.fi
Navigate: Search | Site map
About us: About AfterDawn Ltd | Advertise on our sites | Rules, Restrictions, Legal disclaimer & Privacy policy
Contact us: Send feedback | Contact our media sales team
 
  © 1999-2025 by AfterDawn Ltd.

  IDG TechNetwork