|
|
|
Nero PMA Update failure
|
|
|
angelosbg
Junior Member
|
10. May 2007 @ 05:39 |
Link to this message
|
I have installed windows vista and Nero.Ultra.Edition.Enhanced.v7.8.5.0.
When I want to burn cds everything goes alright.
However when I want to burn dvds everytime it reaches only 1% and then shows PMA Update failure and could not perform Disc-at-once.
So,the burn is cancelled and the dvd is lost...
I have an LG DVDR.
Also when I burn the dvd automatically when I create a movie with ConvertXtoDVD everything goes OK.
Does anyone know what it has to do with?
Is it a software or a hardware problem.
Thanks a lot.
|
|
Advertisement
|
|
|
|
Moderator
|
10. May 2007 @ 10:34 |
Link to this message
|
Hi again angelosbg
Here's my post from the other thread:
It could be a hardware or software problem - hard to say w/o seeing a log. Since ConvertX can get the job done though it may be a Vista/Nero issue.
Try the same suggestion of doing it in 2 steps with Vision.
Convert and save the file to the hard drive instead of burning w/ Nero. Then burn the file w/ Burning Rom or Express.
If it fails post the log - just be sure to edit out the serial # - begins w/ 1A, 1C or 5C.
Let's keep it to this thread (hint forum rules too) since you're problem is a little different then the poster's in the other thread :)
|
|
angelosbg
Junior Member
|
10. May 2007 @ 15:17 |
Link to this message
|
I tried with an image but it failed with the same way
Here is the log
1C80-0000-19E5-MA2X-4001-0754-****
Windows XP 6.0
IA32
WinAspi: -
NT-SPTI used
Nero Version: 7.8.5.0
Internal Version: 7, 8, 5, 0
(Nero Express)
Recorder: <HL-DT-ST DVDRAM GSA-4160B>Version: A300 - HA 1 TA 0 - 7.8.5.0
Adapter driver: <IDE> HA 1
Drive buffer : 2048kB
Bus Type : default (0) -> ATAPI, detected: ?
CD-ROM: <TSSTcorp DVD-ROM TS-H352A>Version: TS01 - HA 1 TA 1 - 7.8.5.0
Adapter driver: <IDE> HA 1
=== Scsi-Device-Map ===
=== CDRom-Device-Map ===
HL-DT-ST DVDRAM GSA-4160B F: CDRom0
TSSTcorp DVD-ROM TS-H352A G: CDRom1
=======================
AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 83886080 (0) Byte
BUFE : 0
Physical memory : 1534MB (1571776kB)
Free physical memory: 790MB (809888kB)
Memory in use : 48 %
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)
11.5.2007
Burn DVD Image
2:02:11 πμ #1 Text 0 File SCSIPTICommands.cpp, Line 411
LockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL
2:02:12 πμ #2 IMAGEGEN -10 File ImageGen.cpp, Line 366
Image was written as DAO.
DAOI:
MediaCatalogNumber = ''
TocType = 0x00
Finalized = 1
First/Last Track = 1 / 1
1: ISRC = ''
Blocksize = 2048
TrackMode = 'TRM_DATA_MODE1'
TrackConfig = 0x00
First/Last Index = 0 / 1
Index0FilePos = 0, Index1FilePos = 0, NextTrackFilePos = 4407328768
CUES:
MTYP: Mediumtype = DVD (old format) (0x1C)
Image file name: <C:\Users\Angel\Desktop\Image.nrg>
2:02:12 πμ #3 Text 0 File Burncd.cpp, Line 3499
Turn on Disc-At-Once, using DVD media
2:02:12 πμ #4 Text 0 File DlgWaitCD.cpp, Line 307
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 2152015 (478:13.40, 4203MB)
2:02:12 πμ #5 Text 0 File DlgWaitCD.cpp, Line 319
Write in overburning mode: NO (enabled: CD)
2:02:12 πμ #6 Text 0 File DlgWaitCD.cpp, Line 2949
Recorder: HL-DT-ST DVDRAM GSA-4160B, Media type: DVD-R
Disc Manufacturer: TYG02 -
Disc Application Code: 64, Disc Physical Code: 193
2:02:12 πμ #7 Text 0 File DlgWaitCD.cpp, Line 493
>>> Protocol of DlgWaitCD activities: <<<
=========================================
2:02:12 πμ #8 Text 0 File ThreadedTransferInterface.cpp, Line 793
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 (1 - DVD-ROM)
2 indices, index0 (150) not provided
original disc pos #0 + 2152016 (2152016) = #2152016/478:13.41
not relocatable, disc pos for caching/writing not required/not required
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2152016 blocks [F: HL-DT-ST DVDRAM GSA-4160B]
--------------------------------------------------------------
2:02:12 πμ #9 Text 0 File ThreadedTransferInterface.cpp, Line 995
Prepare [F: HL-DT-ST DVDRAM GSA-4160B] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1: Idx 0 Idx 1 Next Trk
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4407328768, ISRC ""
DAO layout:
===========
___Start_|____Track_|_Idx_|_CtrlAdr_|_____Size_|______NWA_|_RecDep__________
0 | lead-in | 0 | 0x41 | 0 | 0 | 0x00
0 | 1 | 0 | 0x41 | 0 | 0 | 0x00
0 | 1 | 1 | 0x41 | 2152016 | 0 | 0x00
2152016 | lead-out | 1 | 0x41 | 0 | 0 | 0x00
2:02:12 πμ #10 Text 0 File SCSIPTICommands.cpp, Line 209
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME
2:02:12 πμ #11 Text 0 File Burncd.cpp, Line 4278
Caching options: cache CDRom or Network-Yes, small files-Yes (<64KB)
2:02:12 πμ #12 Phase 24 File dlgbrnst.cpp, Line 1762
Caching of files started
2:02:12 πμ #13 Text 0 File Burncd.cpp, Line 4397
Cache writing successful.
2:02:12 πμ #14 Phase 25 File dlgbrnst.cpp, Line 1762
Caching of files completed
2:02:12 πμ #15 Phase 36 File dlgbrnst.cpp, Line 1762
Burn process started at 8x (11.080 KB/s)
2:02:12 πμ #16 Text 0 File ThreadedTransferInterface.cpp, Line 2721
Verifying disc position of item 0 (not relocatable, no disc pos, no patch infos, orig at #0): write at #0
2:02:12 πμ #17 Text 0 File DVDR.cpp, Line 3192
Recording mode: Sequential Recording Mode
2:02:12 πμ #18 Text 0 File DVDR.cpp, Line 3348
Start write address at LBA 0
DVD high compatibility mode: Yes
2:02:12 πμ #19 Text 0 File Cdrdrv.cpp, Line 9859
---- Disc Structure: Physical Format Information (00h) ----
Media Type: 0, Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 0.0 (0)
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Revision number of maximum recording speed: -
Revision number of minimum recording speed: -
Revision number table of recording speed: - - - - - - -
Class: 0
Start sector number of the current Border-Out: 2FE10 h
Start sector number of the next Border-In: 2FFA0 h
Media Specific [16..63]:
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
00 02 FE 10 00 02 FF A0 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
2:02:12 πμ #20 Text 0 File ThreadedTransfer.cpp, Line 269
Pipe memory size 83836800
2:03:15 πμ #21 SPTI -1194 File SCSIPassThrough.cpp, Line 179
CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1194)
Sense Key: 0x03 (KEY_MEDIUM_ERROR)
Sense Code: 0x73
Sense Qual: 0x04
CDB Data: 0x2A 00 00 00 00 00 00 00 20 00 00 00
Sense Area: 0x70 00 03 00 00 00 00 10 32 38 00 0C 73 04
Buffer x190a0040: Len x10000
0x00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
2:03:15 πμ #22 CDR -1194 File Writer.cpp, Line 303
PMA update failure
F: HL-DT-ST DVDRAM GSA-4160B
2:03:37 πμ #23 Text 0 File DVDR.cpp, Line 3750
EndDAO: Last written address was -1 (FFFFFFFFh)
2:03:37 πμ #24 CDR -1194 File WriterStatus.cpp, Line 162
PMA update failure
F: HL-DT-ST DVDRAM GSA-4160B
2:03:37 πμ #25 TRANSFER -24 File WriterStatus.cpp, Line 162
Could not perform end of Disc-at-once
2:03:37 πμ #26 Phase 38 File dlgbrnst.cpp, Line 1762
Burn process failed at 8x (11.080 KB/s)
2:03:37 πμ #27 Text 0 File SCSIPTICommands.cpp, Line 254
SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME
2:03:42 πμ #28 Text 0 File Cdrdrv.cpp, Line 11214
DriveLocker: UnLockVolume completed
2:03:42 πμ #29 Text 0 File SCSIPTICommands.cpp, Line 411
UnLockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL
Existing drivers:
Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon
|
|
angelosbg
Junior Member
|
10. May 2007 @ 15:25 |
Link to this message
|
|
P.S I do not know why does it say winXP in the beginning.I use vista
|
Moderator
|
10. May 2007 @ 16:04 |
Link to this message
|
That's ok about the XP showing up - you can tell you're running Vista by this in the log - Windows XP 6.0 .
If you were running XP you'd see this - Windows XP 5.1
Just how Nero reports it.
One thing w/ Vista that Nero can't see if the drives are in DMA mode.
Check just to make sure - don't run Vista but should be about the same:
guide
Recorder: <HL-DT-ST DVDRAM GSA-4160B>Version: A300
Drive can use a firmware update too - the latest is A306
Check the DMA mode and update the firmware - see if that does the trick.
Keep us posted too!
|
|
angelosbg
Junior Member
|
10. May 2007 @ 17:16 |
Link to this message
|
|
DMA mode is enabled in both ATA Chanel 0 and ATA Channel 1.
However,the link you sent me for the firmware update drives me to a chnese page where I cannot understand from where can I download it.
Sorry if I am being a dump but I cannot reach the answer
|
Moderator
|
10. May 2007 @ 17:28 |
Link to this message
|
Eck - sorry about that!
Here's another link (checked it this time - english :) ) - link.
|
|
angelosbg
Junior Member
|
10. May 2007 @ 18:07 |
Link to this message
|
Here is my new error report exactly after the firmware update.Everything went in the same way as before.I don't know.....:(
1C80-0000-19E5-MA2X-4001-0754-****
Windows XP 6.0
IA32
WinAspi: -
NT-SPTI used
Nero Version: 7.8.5.0
Internal Version: 7, 8, 5, 0
(Nero Express)
Recorder: <HL-DT-ST DVDRAM GSA-4160B>Version: A306 - HA 1 TA 3 - 7.8.5.0
Adapter driver: <IDE> HA 1
Drive buffer : 2048kB
Bus Type : default (0) -> ATAPI, detected: ?
CD-ROM: <TSSTcorp DVD-ROM TS-H352A>Version: TS01 - HA 1 TA 1 - 7.8.5.0
Adapter driver: <IDE> HA 1
=== Scsi-Device-Map ===
=== CDRom-Device-Map ===
HL-DT-ST DVDRAM GSA-4160B F: CDRom3
TSSTcorp DVD-ROM TS-H352A G: CDRom1
=======================
AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 83886080 (0) Byte
BUFE : 0
Physical memory : 1534MB (1571776kB)
Free physical memory: 909MB (931056kB)
Memory in use : 40 %
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)
11.5.2007
Burn DVD Image
5:00:40 πμ #1 Text 0 File SCSIPTICommands.cpp, Line 411
LockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL
5:00:41 πμ #2 IMAGEGEN -10 File ImageGen.cpp, Line 366
Image was written as DAO.
DAOI:
MediaCatalogNumber = ''
TocType = 0x00
Finalized = 1
First/Last Track = 1 / 1
1: ISRC = ''
Blocksize = 2048
TrackMode = 'TRM_DATA_MODE1'
TrackConfig = 0x00
First/Last Index = 0 / 1
Index0FilePos = 0, Index1FilePos = 0, NextTrackFilePos = 4407328768
CUES:
MTYP: Mediumtype = DVD (old format) (0x1C)
Image file name: <C:\Users\Angel\Desktop\Image.nrg>
5:00:41 πμ #3 Text 0 File Burncd.cpp, Line 3499
Turn on Disc-At-Once, using DVD media
5:00:41 πμ #4 Text 0 File DlgWaitCD.cpp, Line 307
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 2152015 (478:13.40, 4203MB)
5:00:41 πμ #5 Text 0 File DlgWaitCD.cpp, Line 319
Write in overburning mode: NO (enabled: CD)
5:00:41 πμ #6 Text 0 File DlgWaitCD.cpp, Line 2949
Recorder: HL-DT-ST DVDRAM GSA-4160B, Media type: DVD-R
Disc Manufacturer: TYG02 -
Disc Application Code: 64, Disc Physical Code: 193
5:00:41 πμ #7 Text 0 File DlgWaitCD.cpp, Line 493
>>> Protocol of DlgWaitCD activities: <<<
=========================================
5:00:41 πμ #8 Text 0 File ThreadedTransferInterface.cpp, Line 793
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 (1 - DVD-ROM)
2 indices, index0 (150) not provided
original disc pos #0 + 2152016 (2152016) = #2152016/478:13.41
not relocatable, disc pos for caching/writing not required/not required
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2152016 blocks [F: HL-DT-ST DVDRAM GSA-4160B]
--------------------------------------------------------------
5:00:41 πμ #9 Text 0 File ThreadedTransferInterface.cpp, Line 995
Prepare [F: HL-DT-ST DVDRAM GSA-4160B] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1: Idx 0 Idx 1 Next Trk
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4407328768, ISRC ""
DAO layout:
===========
___Start_|____Track_|_Idx_|_CtrlAdr_|_____Size_|______NWA_|_RecDep__________
0 | lead-in | 0 | 0x41 | 0 | 0 | 0x00
0 | 1 | 0 | 0x41 | 0 | 0 | 0x00
0 | 1 | 1 | 0x41 | 2152016 | 0 | 0x00
2152016 | lead-out | 1 | 0x41 | 0 | 0 | 0x00
5:00:41 πμ #10 Text 0 File SCSIPTICommands.cpp, Line 209
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME
5:00:41 πμ #11 Text 0 File Burncd.cpp, Line 4278
Caching options: cache CDRom or Network-Yes, small files-Yes (<64KB)
5:00:41 πμ #12 Phase 24 File dlgbrnst.cpp, Line 1762
Caching of files started
5:00:41 πμ #13 Text 0 File Burncd.cpp, Line 4397
Cache writing successful.
5:00:41 πμ #14 Phase 25 File dlgbrnst.cpp, Line 1762
Caching of files completed
5:00:41 πμ #15 Phase 36 File dlgbrnst.cpp, Line 1762
Burn process started at 8x (11.080 KB/s)
5:00:41 πμ #16 Text 0 File ThreadedTransferInterface.cpp, Line 2721
Verifying disc position of item 0 (not relocatable, no disc pos, no patch infos, orig at #0): write at #0
5:00:41 πμ #17 Text 0 File DVDR.cpp, Line 3192
Recording mode: Sequential Recording Mode
5:00:41 πμ #18 Text 0 File DVDR.cpp, Line 3348
Start write address at LBA 0
DVD high compatibility mode: Yes
5:00:41 πμ #19 Text 0 File Cdrdrv.cpp, Line 9859
---- Disc Structure: Physical Format Information (00h) ----
Media Type: 0, Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 0.0 (0)
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Revision number of maximum recording speed: -
Revision number of minimum recording speed: -
Revision number table of recording speed: - - - - - - -
Class: 0
Start sector number of the current Border-Out: 2FE10 h
Start sector number of the next Border-In: 2FFA0 h
Media Specific [16..63]:
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
00 02 FE 10 00 02 FF A0 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
5:00:41 πμ #20 Text 0 File ThreadedTransfer.cpp, Line 269
Pipe memory size 83836800
5:01:43 πμ #21 SPTI -1194 File SCSIPassThrough.cpp, Line 179
CdRom3: SCSIStatus(x02) WinError(0) NeroError(-1194)
Sense Key: 0x03 (KEY_MEDIUM_ERROR)
Sense Code: 0x73
Sense Qual: 0x04
CDB Data: 0x2A 00 00 00 00 00 00 00 20 00 00 00
Sense Area: 0x70 00 03 00 00 00 00 10 32 38 00 0C 73 04
Buffer x0a430040: Len x10000
0x00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
5:01:43 πμ #22 CDR -1194 File Writer.cpp, Line 303
PMA update failure
F: HL-DT-ST DVDRAM GSA-4160B
5:02:04 πμ #23 Text 0 File DVDR.cpp, Line 3750
EndDAO: Last written address was -1 (FFFFFFFFh)
5:02:04 πμ #24 CDR -1194 File WriterStatus.cpp, Line 162
PMA update failure
F: HL-DT-ST DVDRAM GSA-4160B
5:02:04 πμ #25 TRANSFER -24 File WriterStatus.cpp, Line 162
Could not perform end of Disc-at-once
5:02:04 πμ #26 Phase 38 File dlgbrnst.cpp, Line 1762
Burn process failed at 8x (11.080 KB/s)
5:02:04 πμ #27 Text 0 File SCSIPTICommands.cpp, Line 254
SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME
5:02:09 πμ #28 Text 0 File Cdrdrv.cpp, Line 11214
DriveLocker: UnLockVolume completed
5:02:09 πμ #29 Text 0 File SCSIPTICommands.cpp, Line 411
UnLockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL
Existing drivers:
Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon
|
Moderator
|
10. May 2007 @ 18:20 |
Link to this message
|
Ok - but drats!
Let's try another burning program. ConvertX worked so if this one does then more and more looking like something with Vista and Nero on your setup.
Try ImgBurn - free & good.
Looks like this is already an image file so just use write mode. If not then use build mode to add and burn non image files.
edit to add: Not sure if Nero will also show the drivers that may conflict w/ Vista under existing drivers in the log.
Do you have any Roxio products installed? (dvd/multimedia software like Nero
This message has been edited since posting. Last time this message was edited on 10. May 2007 @ 18:23
|
|
angelosbg
Junior Member
|
10. May 2007 @ 18:32 |
Link to this message
|
Roxio products are products for cd and dvd burning?
Or also Daemon Tools which is for images and powerdvd are of this kind?Because I have them.
So now you suggest to install and try imgburn?Should I have first of all uninstalled Nero or not?
And how can we find the drivers that conflict with vista?
|
Moderator
|
10. May 2007 @ 18:49 |
Link to this message
|
Yeah Roxio is a cd/dvd burning software like Nero. The driver can conflict w/ Nero but sounds like you don't have it installed.
They other program you have listed are fine - not known to conflict w/ Nero.
Any driver that might conflict w/ Nero is listed under Existing drivers: in the log. You have none showing - good thing. Since the Nero log doesn't show everything like it does for XP - just wanted to check to rule out any other possibilities.
No need to uninstall Nero then install ImgBurn. ImgBurn is pretty problem free usually.
Having 2 programs burn and 1 not would more than likely be a Nero issue.
Doing a clean install of Nero but not be a idea either. Uninstall - run the clean tool - reboot and install again.
|
|
angelosbg
Junior Member
|
10. May 2007 @ 19:01 |
Link to this message
|
Quote:
Doing a clean install of Nero but not be a idea either. Uninstall - run the clean tool - reboot and install again.
What do you mean with but not be a idea either?
You mean that I should uninstall Nero and,run the clean tool,reboot and install it again.Some days before I unistalled Nero but without the clean tool and nothing changed.
|
Moderator
|
10. May 2007 @ 19:19 |
Link to this message
|
Just not my night :) Meant might instead of but - god knows why I transposed those words.
Running the clean tool just cleans out Nero entries and gives you a 'fresh' install. Can't hurt to give it a go.
|
|
angelosbg
Junior Member
|
11. May 2007 @ 02:33 |
Link to this message
|
I installed ImgBurn without uninstalling Nero.As you said it wasn't a wrong idea.
This is ImgBurn's error report.It didn't even reach 1%.It remained in 0 and showed this error.
I/O Error!
Device [1:0:0] HL-DT-ST DVDRAM GSA-4160B A306 (F:) (ATA)
ScsiStatus:0x02
Interpretation:Check Condition
CDB:2A 00 00 00 00 00 00 00 20 00
Interpretation:Write (10) - Sectors:0-31
Sense Area:70 00 03 00 00 00 00 10 32 38 00 0C 73 04 00 00 00 00 00 00 00 00 00 00
Interpretation:Program Memory Area Update Failure
If I press retry comes a similar message with this difference:
Sense area:70 00 05 00 00 00 00 10 2A 00 00 0C 30 05 00 00 00 00 00 00 00 00 00 00
Interpretation:Cannot Write Medium - Incompatible Format
I just keep trying and losing Dvds :(
|
Moderator
|
11. May 2007 @ 08:43 |
Link to this message
|
Ok - doesn't look like a Nero issue. ImgBurn is usually pretty problem free even using different os's and is giving you the same error as Nero.
Check the media now - the logs show it's manufactured TYG02 which is a great manufacturer. Check and see if your have the real deal - lot of fakes out there.
Around the hub on the back you should see these codes: GG00xxxx
The x's represent #'s.
Try a different brand of media like Verbatim.
|
|
angelosbg
Junior Member
|
12. May 2007 @ 18:15 |
Link to this message
|
How can I check the media?The dvd labels or the drive?
And what should I see?
Excuse me if I don't understand some things.
Also I have tried to burn a DVD-RW of another label and it didn't work either.
I am starting to believe that there is a problem with my drive and I should buy another...
|
Moderator
|
12. May 2007 @ 20:15 |
Link to this message
|
Check the back of a blank disc - close to around the inner hub you should see GG00xxxx (x's are #'s). May need a magnifying glass:)
The media code in your log - TYG02 is great media but one of the ones faked a lot.
May just be the drive if you've used the same DVD-RW before on it w/ Vista and now a no go.
Try uninstalling the drive in device manager.
These are instructions for XP but I would think Vista is similar.
Right click on my computer. Pick properties>hardware tab>device manager.
Click on the + next to dvd/cd drives. Right click on the drive and pick uninstall. Reboot and let windows do it's thing and reinstall.
|
|
angelosbg
Junior Member
|
15. May 2007 @ 15:39 |
Link to this message
|
The code behind the dvd is GG007009.
I also uninstalled and installed the drive.Then I even used a maxell dvd but nothing had changed with Imgburn.
I don't think that I have another choice instead of buying a new drive...:(
Can you suggest me any DVD-RW label?
Thanks a lot for everything!
|
Moderator
|
15. May 2007 @ 16:10 |
Link to this message
|
|
Dang :(
Well at least you got the real deal on the media - those are genuine Taiyo Yuden.
One last thing you can check - try this drive in another pc - preferable one w/ Vista installed if you can.
Good ones to look at would be LiteOn or Pioneer. If you're in the US check out newegg.com - great prices and service.
|
|
Car.Mike
AfterDawn Addict
|
15. May 2007 @ 17:33 |
Link to this message
|
|
angelosbg ,
Sounds like the drive is dying as the blank media is genuine. That drive is a little old .
|
|
angelosbg
Junior Member
|
17. May 2007 @ 16:36 |
Link to this message
|
|
Yes,the only thing left to do is try it to another pc.
Thanks a lot for everything!
|
Moderator
|
17. May 2007 @ 16:58 |
Link to this message
|
|
You're welcome angelosbg
Keep us posted on the outcome - good, bad or otherwise :)
|
|
angelosbg
Junior Member
|
20. May 2007 @ 18:17 |
Link to this message
|
I have bought a NEC DVD-RW and everything goes ok since...
What do you think about the NEC label?
|
|
Advertisement
|
|
|
Moderator
|
20. May 2007 @ 19:01 |
Link to this message
|
|
I think their good. Quite a few members here use them and love em.
Glad to hear that the new drive is working fine!
|
|
