|
Info regarding sound or other queries within (NO CODE REQUESTS/code POSTING)
|
|
Please note that the forum rules have changed. Posting of new codes is no longer allowed. See this thread for more information.
|
Senior Member
1 product review
|
7. July 2007 @ 01:43 |
Link to this message
|
Originally posted by tommy_c:
Hi again, i was on yesterday after "thebox" and trouble flashing it(not that i know what that means) I'm pretty sure it not a clone according to the picture on that other website. the two skart leads are on theleft hand side as u look at the back of it, the remote doesnt look like the cloned one, and there are 25 vents on the top of the box. should i keep trying to flash with 4eE? how would i know if i have a null modem? im using the cable that i got with the box(vw 15c)?? thanks again
'the box ' is 99% certain that it snot a fake !
null modem cable has 9 pin holes in it.
what is it saying when u try flashing ?
if its not downloading properly u might be better off downloading the gtrom and v4.00e again....get all the info via the eko link under my post ( Starview section. 'software' for gtrom and 'firmware 'for the v4.00e )
This message has been edited since posting. Last time this message was edited on 7. July 2007 @ 01:45
|
|
Advertisement
|
|
|
|
|
ryanmg
Suspended due to non-functional email address
|
7. July 2007 @ 01:50 |
Link to this message
|
|
morning main did you get the pm from eamo.
|
Senior Member
1 product review
|
7. July 2007 @ 02:00 |
Link to this message
|
|
mornin ryan m8 ,sure did.
went on last nite. any way cant have idle chat here any more so ill ask you about the new 'box' firmware out today. is it for mm*s on ch**us ?
|
|
ryanmg
Suspended due to non-functional email address
|
7. July 2007 @ 02:07 |
Link to this message
|
|
had a look its not out yet (had no idea that would happen).but its supposed to work on ch****.
|
|
fergusrb
Suspended permanently
|
7. July 2007 @ 02:28 |
Link to this message
|
Originally posted by ryanmg:
had a look its not out yet (had no idea that would happen).but its supposed to work on ch****.
Ryan the C***** box is still down scouser was mentioning something about a cas 7 do you know what that is also could it be the provider id changed i can get a look at a proper C***** box but i dont know what i need to be looking for also how would get into engineers mode any ideas
|
|
tommy_c
Newbie
|
7. July 2007 @ 02:36 |
Link to this message
|
|
Thanks MAINAMN and everyone else, tried it again and its working great now!Some great info here for anyone with a problem, if i can do it anyone can!!!My initial problem was connecting the tv to the box so it will show u how bad my knowlegde was!!!thanks a million
|
|
ryanmg
Suspended due to non-functional email address
|
7. July 2007 @ 02:39 |
Link to this message
|
Quote:
Originally posted by ryanmg:
had a look its not out yet (had no idea that would happen).but its supposed to work on ch****.
Ryan the C***** box is still down scouser was mentioning something about a cas 7 do you know what that is also could it be the provider id changed i can get a look at a proper C***** box but i dont know what i need to be looking for also how would get into engineers mode any ideas
sorry fergus have no info about the ch*** id and i don't even know what cas 7 is.
|
|
fergusrb
Suspended permanently
|
7. July 2007 @ 03:17 |
Link to this message
|
Originally posted by sc0user:
Mornin :)
Scouser
any news for me on th C***** thing also did you get my pm about putting your stuff on the other page i sent you the link too also if you give me the page numbers i will if you like cut and paste the info for you let me know thanks
|
AfterDawn Addict
|
7. July 2007 @ 03:18 |
Link to this message
|
|
Fergus are the C***** boxes pace boxes if so power of the box, hold down the up and down channel buttons and power the box back on, all the time holding these two buttons.
This will allow you into the engineers menu. I wouldn't advise you to change anything here as the Nagra Info is in hex decimals.
I still have no info as such on C***** as it is hard to obtain this info over a weekend, but I will keep trying. As I said C***** are running a Conax trial in a small area, so I am assuming this hasn't affected you.
Fergus I cannot remember are you MMDS or true cable?
|
AfterDawn Addict
|
7. July 2007 @ 03:21 |
Link to this message
|
Quote:
Originally posted by sc0user:
Mornin :)
Scouser
any news for me on th C***** thing also did you get my pm about putting your stuff on the other page i sent you the link too also if you give me the page numbers i will if you like cut and paste the info for you let me know thanks
Thanks Fergus I ran a leech program through the thread last night and got all the info I needed. I am only here for a while today just trying to give you an update of where I'm at with the C***** problem.
|
|
fergusrb
Suspended permanently
|
7. July 2007 @ 03:22 |
Link to this message
|
Originally posted by sc0user:
Fergus are the C***** boxes pace boxes if so power of the box, hold down the up and down channel buttons and power the box back on, all the time holding these two buttons.
This will allow you into the engineers menu. I wouldn't advise you to change anything here as the Nagra Info is in hex decimals.
I still have no info as such on C***** as it is hard to obtain this info over a weekend, but I will keep trying. As I said C***** are running a Conax trial in a small area, so I am assuming this hasn't affected you.
Fergus I cannot remember are you MMDS or true cable?
No true cable i cannot understand how i can be receiving the uk docs program and yet i cannot receive the free to air our own channels
|
AfterDawn Addict
|
7. July 2007 @ 03:24 |
Link to this message
|
Quote:
Originally posted by sc0user:
Fergus are the C***** boxes pace boxes if so power of the box, hold down the up and down channel buttons and power the box back on, all the time holding these two buttons.
This will allow you into the engineers menu. I wouldn't advise you to change anything here as the Nagra Info is in hex decimals.
I still have no info as such on C***** as it is hard to obtain this info over a weekend, but I will keep trying. As I said C***** are running a Conax trial in a small area, so I am assuming this hasn't affected you.
Fergus I cannot remember are you MMDS or true cable?
No true cable i cannot understand how i can be receiving the uk docs program and yet i cannot receive the free to air our own channels
What Channels can you get as this sounds like a frequency shift by C*****?
This message has been edited since posting. Last time this message was edited on 7. July 2007 @ 03:25
|
|
ryanmg
Suspended due to non-functional email address
|
7. July 2007 @ 03:26 |
Link to this message
|
|
does it say scrambled or bad channel or data is being updated on the fta channels.
|
|
fergusrb
Suspended permanently
|
7. July 2007 @ 03:30 |
Link to this message
|
|
I can only receive 1 channel from the uk it is uk Docs all the other channels when i pick one it is just a black screen the starts updating but never stops dont even receive our own free to air as the $ symbol are on them
|
|
ryanmg
Suspended due to non-functional email address
|
7. July 2007 @ 03:30 |
Link to this message
|
|
just found out the new firmware for "the box" will be out i a couple of hours.
also afternoon martin
|
|
ryanmg
Suspended due to non-functional email address
|
7. July 2007 @ 03:34 |
Link to this message
|
|
well fergus hopefully the new firmware does come out and works and someone with "the box" on c***** puts it on there box and the codes update and they post them.
|
|
fergusrb
Suspended permanently
|
7. July 2007 @ 03:39 |
Link to this message
|
Originally posted by ryanmg:
well fergus hopefully the new firmware does come out and works and someone with "the box" on c***** puts it on there box and the codes update and they post them.
Ya problem if they have the box and they do they will not need to come here and therefore you will still not get the codes but all we can do is hope i am going to go across to my PAL who has the proper box and have a gander at his see if i can get any info of it maybe they have changed the provider id will let you know
|
|
ryanmg
Suspended due to non-functional email address
|
7. July 2007 @ 03:41 |
Link to this message
|
|
i am going out cya all later,fergus hope you get your box fixed and i hope the new firmware is out by the time i get back.also i have a strange feeling there is going to be a n** key change.so see you all later :)
|
AfterDawn Addict
|
7. July 2007 @ 03:42 |
Link to this message
|
Originally posted by ryanmg:
well fergus hopefully the new firmware does come out and works and someone with "the box" on c***** puts it on there box and the codes update and they post them.
Morning Ryan from the info I have heard the new firmware is only for "the box" and not Starview am I right in assuming that as there is quite a few people in C***** land that are annoyed to say the least that after buying a Starview they are not been supported by the FW upgrade.
On that note I have to head so I will catch you all later
|
AfterDawn Addict
|
7. July 2007 @ 05:15 |
Link to this message
|
|
Afternoon all ,I agree Ryan , I think they will change soo , Last weekend I think we had 3 in total lol
|
|
fergusrb
Suspended permanently
|
7. July 2007 @ 05:31 |
Link to this message
|
|
Scouser
Have had a look at the boxes and they are sagam so tried the up and down holding the buttons no joy just come up as error
|
|
ryanmg
Suspended due to non-functional email address
|
7. July 2007 @ 09:01 |
Link to this message
|
yeah sc0user the firmware is only for the box and there are alot of unhappy people who bought a Starview 2-3 months ago just because of the support your supposed to get.and now they find out well its to late we made a new box so buy that or no channels for you.also from what i read the Starview was never meant to work on ch**** it was a coincidence that v2.58 worked.but fergus you have v4 on your and it works don't you.
This message has been edited since posting. Last time this message was edited on 7. July 2007 @ 09:01
|
|
ryanmg
Suspended due to non-functional email address
|
7. July 2007 @ 10:56 |
Link to this message
|
|
|
fergusrb
Suspended permanently
|
7. July 2007 @ 12:05 |
Link to this message
|
|
Yes i have v4 on mine and it worked perfect until the codes changed before i came back still no joy on the box i have put v2.57 your one on the other boxes and you dont even have to put the code into it as soon as you are finished scanning and turn on the emu the stations come on straight away so that is a success for th N** customers with clones
I have just got the new codes and am back up and running again they will be posted on the link under my post if anybody needs them
This message has been edited since posting. Last time this message was edited on 7. July 2007 @ 13:15
|
|
Advertisement
|
|
|
|
JohnIRL
Newbie
|
7. July 2007 @ 13:46 |
Link to this message
|
|
Evenin all.
Just got an SV for a friend with Ver4 already on it. He said he has only about 50 channels. I told him to make sure the EMU was on and to do an automatic scan. Got nothing on this or on a manual scan. All the other channels just comes up scrambled or bad channel. Any advice. Oh and if I were to restore the fac. set. on a box with ver4, would ver4 be deleted as such?
Thanks,
John
|
