|
The disc could not be read !! (UMD)
|
|
|
assadi84
Member
|
8. October 2007 @ 13:02 |
Link to this message
|
|
I have this issue after unbricking the PSP, i tried everything i could think of, with no use, i even tried changing the laser it self but still with the same error!!
Any suggestions
|
|
Advertisement
|
|
|
|
|
Hacker06
Suspended permanently
|
8. October 2007 @ 13:12 |
Link to this message
|
|
well havent heard of this ever happening. mabey the disk is scracthed?
|
|
sic(ness)
Junior Member
|
8. October 2007 @ 15:01 |
Link to this message
|
|
what is the condition of the UMD?
|
|
assadi84
Member
|
9. October 2007 @ 10:56 |
Link to this message
|
|
I tried many different UMDs, same result, and i even tried the same UMD on different PSP, and all working fine.. I know that its something to do with the software side, but i tried unbricking many times with the psp which formats all the flashes and reset all system files, but still same result, over and over again, even the UMD icon wont appear, it loads for few seconds and the error pops up!! I guess there is a first thing for everything :S
|
Member
|
9. October 2007 @ 14:38 |
Link to this message
|
|
What's the error code?
Anyway, if u are running CFW go into the recovery menu.
Select advanced.
Select advanced configuration.
Disable everything in this menu.
Worked for me :P
-------- --------
.rave
|
|
assadi84
Member
|
11. October 2007 @ 14:14 |
Link to this message
|
|
The error has no number, just what i said before, and in the recovery, those settings are already disabled, no use..
|
|
Hacker06
Suspended permanently
|
11. October 2007 @ 14:20 |
Link to this message
|
|
did you turn off the read umd. thats what you do when you have iso's and whant to play them without a UMD Inserted. and did you drop it reently because the laser might be broken
|
|
h1r0
Newbie
|
12. October 2007 @ 02:19 |
Link to this message
|
|
hello guys
i do some repairs in PSP recently i received one PSP that have fell out and have the rear cover breaked i've replaced the rear cover and perform some reading tests and it was working perfectly. but during the assembly one of the buttons wasn't working precisly so i opened and put everything in place and close PSP ( this isn't the 1st time that i do that) but sudently the PSP cannot read the UMD
allready check the cables and replaced the laser
also
run pandoras also install a CFW (3.40 OEA) and message persists.
replaced the battery: same issue
i can ear the UMD spinning and the laser moving for a couple os seconds and sudently it stoped
i'll try now to desable the UMD reading options in the PSP and then post in here
but if you have better ideias please post here :D
|
|
assadi84
Member
|
17. October 2007 @ 11:47 |
Link to this message
|
Originally posted by h1r0:
hello guys
i do some repairs in PSP recently i received one PSP that have fell out and have the rear cover breaked i've replaced the rear cover and perform some reading tests and it was working perfectly. but during the assembly one of the buttons wasn't working precisly so i opened and put everything in place and close PSP ( this isn't the 1st time that i do that) but sudently the PSP cannot read the UMD
allready check the cables and replaced the laser
also
run pandoras also install a CFW (3.40 OEA) and message persists.
replaced the battery: same issue
i can ear the UMD spinning and the laser moving for a couple os seconds and sudently it stoped
i'll try now to desable the UMD reading options in the PSP and then post in here
but if you have better ideias please post here :D
Found any solutions yet ? cuz im still trying with no use.
|
|
h1r0
Newbie
|
18. October 2007 @ 07:16 |
Link to this message
|
|
today i'll tray to test with another board :P
then i 'll post here
|
|
kingofsg
Newbie
|
27. November 2007 @ 10:44 |
Link to this message
|
|
Hi assadi84,
May i ask:
1) How did you unbrick ur set? Did you press L+R+START+HOME?
2) What is the steps you took to unbrick?
I am experiencing such probs. I've unbrick my set using another person's nand DUMP. A little guess here (if anyone can clarify) is that each individual umd is diff frm e others, using another person's dump will cause it not to function as it cannot recognise its own umd drive. I am looking for help in this forum to see if anyone can help in clarifying my guess.
Hopefully, a prog will be released to help us fix this issue similiar to MacFixer created by Cory.
Hope this helps.:)
|
|
MWRO13
Newbie
|
25. May 2008 @ 17:58 |
Link to this message
|
Well man i think that your problem is on your mainboard's flash memory and not to the umd unit. The guy that asked you if you restored the dump (nand) by full mode is right because if you did you messed up the internal units adresses so from now on your console will only play games under custom firmwares only.
|
|
deniros
Newbie
|
23. July 2008 @ 17:17 |
Link to this message
|
i have this problem too,cannot read umd,but the second i close the umd drawer(with the umd in)i hear a beep and the "the disc could not be read" appears.it doesnt even attempt to read the disc so im assuming its something to do with the firmware,bringing it back tomorrow
|
|
gothik
Newbie
|
13. September 2008 @ 16:41 |
Link to this message
|
Try restoring the original settings of the PSP... under system settings, it worked for me !!!!
|
|
Advertisement
|
|
|
Senior Member
2 product reviews
|
13. September 2008 @ 16:46 |
Link to this message
|
|
Try not responding to 3 month old threads.
Does anorexia induce constipation?
~~~~~~~~~~~~~~
Ive become so paranoid, that Im paranoid about my paranoia....
|
