|
Help on replacing xbox 360 dvd drive.
|
|
|
riotcodes
Newbie
|
28. March 2008 @ 19:22 |
Link to this message
|
I need to replace my xbox 360 dvd drive because it is slipping.
I have a hitcahi right now and I tend to replace it with another hitcahi. Will that require flashing? I'm not looking to play back up's either. Please help me.
|
|
Advertisement
|
|
|
|
AfterDawn Addict
|
28. March 2008 @ 19:26 |
Link to this message
|
|
ya, you will have to flash the new dvd drive with the old drives firmware so it will work.
|
|
ccampton
Suspended permanently
|
29. March 2008 @ 09:23 |
Link to this message
|
yea the box and the drive have a "key" and they have to match so essentially you need to get the "key" form your old drive and put it on your new drive in order to get it to work.
|
|
Rebel1969
Newbie
|
31. March 2008 @ 22:22 |
Link to this message
|
|
What if your old dvd drive is completely shot? How do you go about flashing a new dvd drive when you can't get key off the original drive?
|
AfterDawn Addict
|
31. March 2008 @ 23:53 |
Link to this message
|
|
well if the old drive is completely shot and you cant dump the FW off of it and you dont have it somewhere else (already modded it so you have the orig.bin for that drive) you are screwed pretty much and cant do anything.
|
|
toks64
Suspended due to non-functional email address
|
16. July 2008 @ 21:06 |
Link to this message
|
I am so Confused
I really want to learn how to replace my xbox 360 dvd drive but it sounds quite complicated.
Flash.....Key??????
I see xbox 360 replacement dvd drives online
1st of all is flashing the dvd drive that green circuit board that you have to switch from old drive to new drive?
2nd where is the key? Where do I get the Key from?
is the key supposed to be in the dvd drive circuit Board?
someone please help me understand.
|
Senior Member
|
16. July 2008 @ 22:00 |
Link to this message
|
The key is normally stored in the drive controller chip,but it is different for the new Lite-On drives.The only option you have to recover your orig.bin file if the board is shot is with a programmer and a 14mm TSOP32 adapter.You will need to desolder the TSOP chip and read the firmware that way if the TSOP chip is still good.Whether you are using hacked firmware or original firmware the key for your drive should be located on it.The key has to match your main motherboard in order for it to work.
...........................:SiG cReAtEd By Phantom69:............................ |
|
toks64
Suspended due to non-functional email address
|
16. July 2008 @ 22:34 |
Link to this message
|
My DVD Drive still works
It just does Grinding Noise sometimes won't eject
My dvd drive is still good
so If I bought a Brand New DVD Drive and took my motherboard from my old dvd drive and put it on my new motherboard will everything work out fine?
|
Senior Member
|
16. July 2008 @ 22:38 |
Link to this message
|
Yeah it should but if you have a Hitachi drive replace it with a Hitachi.Try to keep the drive the same if you plan on swapping just the board.
...........................:SiG cReAtEd By Phantom69:............................
|
|
toks64
Suspended due to non-functional email address
|
16. July 2008 @ 22:44 |
Link to this message
|
My DVD Drive has one hole in the disc tray
I have been told twice that I have a samsung/toshiba drive m25
that is what I should get right?
as long as I have m25
put my old motherboard in the new drive I should be fine right?
|
Senior Member
|
16. July 2008 @ 22:53 |
Link to this message
|
Yeah it will work bro,just replace your m25 board with a new m25 drive and you should be in business.I would also make sure it is a m25 before getting a new drive.If you can do it open up your console and check to make sure before you change it out.If you can do the extra step I would advise it.
...........................:SiG cReAtEd By Phantom69:............................
This message has been edited since posting. Last time this message was edited on 16. July 2008 @ 23:05
|
|
DUKE2441
Newbie
|
24. July 2008 @ 14:58 |
Link to this message
|
Hi please help when I try to play games on my xbox a white screen comes up with "to play this disk put it in an xbox 360 console" I have read that this is due to a bad dvd drive I have the Toshiba/Samsung TS-H943A DVD Drive but I dont know if its the MS25 or MS28 do you think if I change the drive and put the old board on it will work or should i just flash the new one
|
|
DatPSPGuy
Suspended due to non-functional email address
|
2. August 2008 @ 19:56 |
Link to this message
|
Im in the same situation...please help
My dvd drive is worn out...m28 flashed to play backups and i just purchased a m25 their both samsung so idc..
I have the key files, but what do i do with them to flash the new drive will it automatically play backups or do i flash it with the key then flash it to play backups again?
hey can someone help me put an image here?
|
Senior Member
|
2. August 2008 @ 20:07 |
Link to this message
|
This is what I would do alright if you have an ms28 drive and want to swap it out with a ms25 drive.Then dump the firmware from the ms25 and inject the key from the ms28 into it,then flash it back by doing a restore.In order to do a restore though you need the orig.bin file.If you have a ms28 and want to swap the board with a ms25 then it should work,because there is really nothing different between them.
...........................:SiG cReAtEd By Phantom69:............................
|
|
towerfu
Suspended due to non-functional email address
|
18. August 2008 @ 13:40 |
Link to this message
|
|
Hi, sorry if I sound like a moron, but if I simply replace my faulty drive with the new one I`ve ordered I dont have to flash it? its an M25 I know that much. And if I have to flash it I take the key off the broken one and flash into the new one? which program do I need I can only find tutorials to mess with the drive so you can copy games (I think).
|
|
dfitz0808
Newbie
|
14. January 2009 @ 21:55 |
Link to this message
|
i have an old 360 i bought it used, and it has a hitachi drive in it thats not working right. i bought a samsung toshiba drive off ebay and didn't have a clue about flashing or anything, can i make it work? oh yeah, i have no clue what im doing so anything will help, THANKS!!
|
|
aj123
Member
|
14. January 2009 @ 22:31 |
Link to this message
|
Originally posted by L-Burna:
This is what I would do alright if you have an ms28 drive and want to swap it out with a ms25 drive.Then dump the firmware from the ms25 and inject the key from the ms28 into it,then flash it back by doing a restore.In order to do a restore though you need the orig.bin file.If you have a ms28 and want to swap the board with a ms25 then it should work,because there is really nothing different between them.
the only thing i need from the old drive is the key right? and it will work with any new drive i put like a BenQ?
This message has been edited since posting. Last time this message was edited on 14. January 2009 @ 22:31
|
|
JakeyT
Newbie
|
6. February 2009 @ 18:32 |
Link to this message
|
Okay i just want to know, my dvd drive as completely failed i can buy a new Hitachi dvd drive but i dont want to have to open up my computer to fix my xbox, so can i just take out the chip in my old dvd drive and put it into the new one or do i still have to flash it?
|
|
Geared_up
Newbie
|
11. February 2009 @ 02:30 |
Link to this message
|
Originally posted by L-Burna:
Yeah it will work bro,just replace your m25 board with a new m25 drive and you should be in business.I would also make sure it is a m25 before getting a new drive.If you can do it open up your console and check to make sure before you change it out.If you can do the extra step I would advise it.
This is a proven and effective way. I have dona it a couple times and has always worked. Plus its easy for beginners. Requires very minimal soldering skills.
|
|
Geared_up
Newbie
|
11. February 2009 @ 02:35 |
Link to this message
|
Originally posted by JakeyT:
Okay i just want to know, my dvd drive as completely failed i can buy a new Hitachi dvd drive but i dont want to have to open up my computer to fix my xbox, so can i just take out the chip in my old dvd drive and put it into the new one or do i still have to flash it?
You need to make sure your buying the right drive. No you do not have to flash it. And you must desolder the 8 wires pull the pcb out and swap it. Then resolder the wires. You must keep a close eye on the order of the wires please mark them as it is very easy to mix them up. It should be if I remember correctly (black,Red,white,white,red,black,white white from left to right.)
|
|
|CL|
Member
|
11. February 2009 @ 02:45 |
Link to this message
|
Originally posted by Geared_up:
Originally posted by JakeyT:
Okay i just want to know, my dvd drive as completely failed i can buy a new Hitachi dvd drive but i dont want to have to open up my computer to fix my xbox, so can i just take out the chip in my old dvd drive and put it into the new one or do i still have to flash it?
You need to make sure your buying the right drive. No you do not have to flash it. And you must desolder the 8 wires pull the pcb out and swap it. Then resolder the wires. You must keep a close eye on the order of the wires please mark them as it is very easy to mix them up. It should be if I remember correctly (black,Red,white,white,red,black,white white from left to right.)
First off, you are replying to something that is from March '08.
Second, since it's an Hitachi drive, there are NO wires to desolder/solder. I believe it's the BenQ that you are thinking of.
|
|
Geared_up
Newbie
|
11. February 2009 @ 03:10 |
Link to this message
|
Originally posted by |CL|:
Originally posted by Geared_up:
Originally posted by JakeyT:
Okay i just want to know, my dvd drive as completely failed i can buy a new Hitachi dvd drive but i dont want to have to open up my computer to fix my xbox, so can i just take out the chip in my old dvd drive and put it into the new one or do i still have to flash it?
You need to make sure your buying the right drive. No you do not have to flash it. And you must desolder the 8 wires pull the pcb out and swap it. Then resolder the wires. You must keep a close eye on the order of the wires please mark them as it is very easy to mix them up. It should be if I remember correctly (black,Red,white,white,red,black,white white from left to right.)
First off, you are replying to something that is from March '08.
Second, since it's an Hitachi drive, there are NO wires to desolder/solder. I believe it's the BenQ that you are thinking of.
I am sorry your right it is the benq I am thinking about, but the post is from feb 06 2009 I replied to on this particular inquire.
|
|
|CL|
Member
|
11. February 2009 @ 03:16 |
Link to this message
|
Originally posted by Geared_up:
Originally posted by |CL|:
Originally posted by Geared_up:
Originally posted by JakeyT:
Okay i just want to know, my dvd drive as completely failed i can buy a new Hitachi dvd drive but i dont want to have to open up my computer to fix my xbox, so can i just take out the chip in my old dvd drive and put it into the new one or do i still have to flash it?
You need to make sure your buying the right drive. No you do not have to flash it. And you must desolder the 8 wires pull the pcb out and swap it. Then resolder the wires. You must keep a close eye on the order of the wires please mark them as it is very easy to mix them up. It should be if I remember correctly (black,Red,white,white,red,black,white white from left to right.)
First off, you are replying to something that is from March '08.
Second, since it's an Hitachi drive, there are NO wires to desolder/solder. I believe it's the BenQ that you are thinking of.
I am sorry your right it is the benq I am thinking about, but the post is from feb 06 2009 I replied to on this particular inquire.
Yup, you're right.
See how easy it is to make a mistake? :)
|
|
skenn11
Newbie
|
21. March 2009 @ 18:39 |
Link to this message
|
Please forgive my ignorance; the more read this post, the more confused I get. My drive is also shot. Can I just replace the Hitachi version 79F with a Hitachi version 79F and start playing?
|
|
Advertisement
|
|
|
|
buttons09
Newbie
|
4. April 2009 @ 03:50 |
Link to this message
|
i have an xbox with a flashed samsung drive. im trying to install it into my little brothers xbox witch has a benq drive. i know i need to make the keys match. but im new to all the tech stuff. so if someone could be kind enough to give me a step by step tutorial it'd be greatly appreciated.
buttons
|
