|
For flashing i believe i need a NULL MODEM cable?
|
|
|
DEAN1987
Suspended due to non-functional email address
|
1. December 2008 @ 06:56 |
Link to this message
|
Hi all, i'm about to have a go for the first time at updating the firmware on my box (Starview 2, when the fix is released) and i just want to be sure on what i need exactly...
I am going to follow the guides on here and hopefully i can do it! I've read that i need a NULL MODEM cable? Is that the only cable i need, and i have the 9 pin thing at the back of my computer, is that ok or will i have to buy any adaptor?
Also looking on ebay, there's different length cables, will the box have to be connected up to the TV when i update it, if so i will need a fairly long cable as my computer is quite far away from it...
Appreciate any help, i just wanna make sure i have the right equipment to start with!
|
|
Advertisement
|
|
|
|
|
jj67
Junior Member
|
1. December 2008 @ 07:17 |
Link to this message
|
|
hi mate, null modem cable is all you will need and box doesnt have to be connected to tv when flashing
|
Senior Member
|
1. December 2008 @ 07:18 |
Link to this message
|
|
If you have 9 pin in your pc all you will need is the null modem cable.
The length isn't important as the box isn't plugged into tv while updating, only the computer.
|
|
DEAN1987
Suspended due to non-functional email address
|
1. December 2008 @ 07:26 |
Link to this message
|
|
Brilliant thanks lads, so the box definetly does not have to be on or connected to the TV when updating, just to the PC? If that's the case i'll buy the cheaper cable which is the 2 metre length, and that should be fine?
Cheers
|
Moderator
|
1. December 2008 @ 08:04 |
Link to this message
|
Main PC ~ Intel C2Q Q6600 (G0 Stepping)/Gigabyte GA-EP45-DS3/2GB Crucial Ballistix PC2-8500/Zalman CNPS9700/Antec 900/Corsair HX 620W
Network ~ DD-WRT ~ 2node WDS-WPA2/AES ~ Buffalo WHR-G54S. 3node WPA2/AES ~ WRT54GS v6 (inc. WEP BSSID), WRT54G v2, WRT54G2 v1. *** Forum Rules *** |
|
DEAN1987
Suspended due to non-functional email address
|
1. December 2008 @ 08:14 |
Link to this message
|
|
|
|
jj67
Junior Member
|
1. December 2008 @ 08:19 |
Link to this message
|
|
hi dean that will be fine, box needs to be on standby but not connected to tv when updating.
|
AfterDawn Addict
|
1. December 2008 @ 08:25 |
Link to this message
|
|
|
DEAN1987
Suspended due to non-functional email address
|
1. December 2008 @ 08:27 |
Link to this message
|
|
lol ok this can get a bit confusing for a novice like me! So i can plug the box in, but it don't have to be connected up, just plugged in and on standby, then i connect the cable to it and the pc, and then basically download the software from here, and then it's done?
How long does it take to flash?
Thanks for your help jj
This message has been edited since posting. Last time this message was edited on 1. December 2008 @ 08:28
|
|
jusandjan
Junior Member
|
1. December 2008 @ 08:28 |
Link to this message
|
|
I have a null modem cable and have connected to back of my PC ans to my SV3. what now??/ how do i add the com ports for it or is there something else
|
|
malci
Suspended due to non-functional email address
|
1. December 2008 @ 08:31 |
Link to this message
|
Originally posted by jusandjan:
I have a null modem cable and have connected to back of my PC ans to my SV3. what now??/ how do i add the com ports for it or is there something else
If you have the correct recent firmware of yesterday, then go to the Starview Link at the bottom of post 2nd line and follow the guide.
|
|
jusandjan
Junior Member
|
1. December 2008 @ 08:37 |
Link to this message
|
i have had a look at that link but its all about USB, there nothing how you set up null modem cable. I've had a look in the ports and there is nothing there for serial com
|
|
jj67
Junior Member
|
1. December 2008 @ 08:38 |
Link to this message
|
Originally posted by DEAN1987:
lol ok this can get a bit confusing for a novice like me! So i can plug the box in, but it don't have to be connected up, just plugged in and on standby, then i connect the cable to it and the pc, and then basically download the software from here, and then it's done?
How long does it take to flash?
Thanks for your help jj
dean, it takes about 10 mins to flash,step by step instructions can be viewed in malcis post under starview link.download new firmware to your pc when it becomes available.
|
|
Advertisement
|
|
|
AfterDawn Addict
|
1. December 2008 @ 08:42 |
Link to this message
|
Originally posted by jusandjan:
i have had a look at that link but its all about USB, there nothing how you set up null modem cable. I've had a look in the ports and there is nothing there for serial com
Updating Firmw@re SV 1/2/3
Connect your box and PC with a Null modem cable and switch on the cable box and put it on STANDBY.
(The Starvi*w does not need to be connected to TV to update it with GTROM)
Open GTROM Loader software make sure that you set the correct COM PORT that matches the one that is being used
Make sure App file only is selected, then click b1n File & browse to the firmw@re where you downloaded it to on your PC.
Run the GTROM loader by pressing Download and you will see the % progress increase then Download completed message on your PC.
Wait until you see the DOWNLOAD COMPLETE p0p up on your PC before removing the NULL MODEM CABLE.
The Starvi*w will then reboot
Disconnect from PC and connect back up to the TV :)
|
