|
eurovox red no signal
|
|
|
arny321
Newbie
|
1. December 2008 @ 19:16 |
Link to this message
|
hi all got the new firmware since putting on my box im getting no signal (not even on free channels)reloaded old firmware fault is still the same tried blue eurovox everything works ok(to prove cable ect)could my box just of gone faulty beens as i haveent even got free channels.....thanks to all those who have sorted probs over past few days its been hell.....
|
|
Advertisement
|
 |
|
|
AfterDawn Addict
2 product reviews
|
1. December 2008 @ 21:21 |
Link to this message
|
Click on the link at the bottom of my with regards to eurovox flashing guide and read carefully through the powerscan instructions, make sure you are selecting the correct symbol rate for your area.
You could also upload your CDF=(channel Dump File) from your blue box save it to your PC then download it to your red box.
Read first then come back if your still stuck.
|
|
arny321
Newbie
|
2. December 2008 @ 04:29 |
Link to this message
|
thanks for getting in touch checked all settings everythink seems ok just think that my box has gone faulty has i cannot even get free channels,able to download firmware no problem just got no signal
|
|
arny321
Newbie
|
2. December 2008 @ 15:14 |
Link to this message
|
hi is anyone else got same probs as my previous posts still got no signal stuck at 5% on red eurovox even putting old firmware back on fault still same
|
|
shardend
Suspended due to non-functional email address
|
2. December 2008 @ 17:06 |
Link to this message
|
hi mate when a eurovox says no signal the power board is faulty. turn your box on and listen to see if you can hear a hising noise
|
|
captsmith
Newbie
|
3. December 2008 @ 05:39 |
Link to this message
|
Originally posted by arny321:
hi is anyone else got same probs as my previous posts still got no signal stuck at 5% on red eurovox even putting old firmware back on fault still same
|
|
captsmith
Newbie
|
3. December 2008 @ 05:43 |
Link to this message
|
Originally posted by arny321:
hi is anyone else got same probs as my previous posts still got no signal stuck at 5% on red eurovox even putting old firmware back on fault still same
hi i have the eurovox max blue i have just downloaded the new firmware v2.0 into it and now all it will do is switch on with nothing on the screen and 001 in the box window, the remote or buttons on the box wont do anyhthing only switch it on and off so now i am left with no channels,, can anybody help please,,,,
steve
|
|
shardend
Suspended due to non-functional email address
|
3. December 2008 @ 09:19 |
Link to this message
|
|
it sounds like a bad flash mate have you tried reflashing it again. if that dont work you will have to j-tag it
|
|
1shaddow1
Member
|
3. December 2008 @ 09:29 |
Link to this message
|
|
no signal means just that, is your cable connected to the rite socket (rf in)?
|
AfterDawn Addict
2 product reviews
|
3. December 2008 @ 09:35 |
Link to this message
|
Originally posted by captsmith:
Originally posted by arny321:
hi is anyone else got same probs as my previous posts still got no signal stuck at 5% on red eurovox even putting old firmware back on fault still same
hi i have the eurovox max blue i have just downloaded the new firmware v2.0 into it and now all it will do is switch on with nothing on the screen and 001 in the box window, the remote or buttons on the box wont do anyhthing only switch it on and off so now i am left with no channels,, can anybody help please,,,,
steve
Another one thats probably put the genuine eurovox blue fix on a cloned box ?, did you check to see if it was a clone before flashing it?.
Back to the original poster
arny321 as 1shaddow1 just said make sure your feed is plugged into the RF in at the back of your box and not the ANT, factory default then powerscan.
This message has been edited since posting. Last time this message was edited on 3. December 2008 @ 09:36
|
|
1shaddow1
Member
|
3. December 2008 @ 09:42 |
Link to this message
|
|
further to this, i have just this min flashed my orig blue box and it all went smooth no issues
|
|
peapods
Suspended due to non-functional email address
|
3. December 2008 @ 09:44 |
Link to this message
|
|
Depends on where you are,but VM have reported loss of signal in a few places, including TV,phone and internet. Look on service status to see if you are in areas affected, a lot went down this morning
|
|
captsmith
Newbie
|
3. December 2008 @ 09:57 |
Link to this message
|
Originally posted by HiTeck:
Originally posted by captsmith:
Originally posted by arny321:
hi is anyone else got same probs as my previous posts still got no signal stuck at 5% on red eurovox even putting old firmware back on fault still same
hi i have the eurovox max blue i have just downloaded the new firmware v2.0 into it and now all it will do is switch on with nothing on the screen and 001 in the box window, the remote or buttons on the box wont do anyhthing only switch it on and off so now i am left with no channels,, can anybody help please,,,,
steve
Another one thats probably put the genuine eurovox blue fix on a cloned box ?, did you check to see if it was a clone before flashing it?.
hi i have been on a different thread to find out, and yes it is a cloned box i have sent for the jtagged kit off ebay to try and fix this,,
Back to the original poster
arny321 as 1shaddow1 just said make sure your feed is plugged into the RF in at the back of your box and not the ANT, factory default then powerscan.
|
|
arny321
Newbie
|
3. December 2008 @ 12:07 |
Link to this message
|
|
hi all cable is in rf in still no signal as regards power supply fault had this replaced last year when box would not power up at all please help........
|
|
1shaddow1
Member
|
3. December 2008 @ 12:11 |
Link to this message
|
|
try a factory reset then powerscan, jus even check ALL connections right back to ya incomming source, does the vm box work ok?
|
|
captsmith
Newbie
|
3. December 2008 @ 12:12 |
Link to this message
|
Originally posted by captsmith:
Originally posted by HiTeck:
Originally posted by captsmith:
Originally posted by arny321:
hi is anyone else got same probs as my previous posts still got no signal stuck at 5% on red eurovox even putting old firmware back on fault still same
hi i have the eurovox max blue i have just downloaded the new firmware v2.0 into it and now all it will do is switch on with nothing on the screen and 001 in the box window, the remote or buttons on the box wont do anyhthing only switch it on and off so now i am left with no channels,, can anybody help please,,,,
steve
Another one thats probably put the genuine eurovox blue fix on a cloned box ?, did you check to see if it was a clone before flashing it?.
hi i have been on a different thread to find out, and yes it is a cloned box i have sent for the jtagged kit off ebay to try and fix this,,
Back to the original poster
arny321 as 1shaddow1 just said make sure your feed is plugged into the RF in at the back of your box and not the ANT, factory default then powerscan.
i will mate,, thanks for that,
|
|
arny321
Newbie
|
3. December 2008 @ 12:22 |
Link to this message
|
not got a vm box got another euro max v works all ok tried all connections could it be that the tuner board has died all of a sudden dont think its the firmware either currently on
dvb xc box tda
s/w stc4 apr 21 2008
h/w 2.0t
bootstrap v002
|
AfterDawn Addict
2 product reviews
|
3. December 2008 @ 12:55 |
Link to this message
|
|
Take the CDF from your Max V and put it on your Red box, If that doesn't work in the exact place of your Max V then I would say the tuners had it.
|
Member
|
3. December 2008 @ 13:31 |
Link to this message
|
|
HiTeck - is there a quick way of uploading/downloading a CDF or is it only while reflashing as per your script? Cheers
It*s good to talk |
|
1shaddow1
Member
|
3. December 2008 @ 13:37 |
Link to this message
|
|
jus do the channel data file and not the flash, but its done the same way with the same ufl.
|
Member
|
3. December 2008 @ 13:40 |
Link to this message
|
Originally posted by 1shaddow1:
jus do the channel data file and not the flash, but its done the same way with the same ufl.
Thanks - was that an option when I ran the ufl. I've slept since I reflashed !!! Just to save me getting the leads out again etc :-/(Memory Man)
It*s good to talk
|
Member
|
3. December 2008 @ 13:42 |
Link to this message
|
Originally posted by kopitekid:
Originally posted by 1shaddow1:
jus do the channel data file and not the flash, but its done the same way with the same ufl.
Thanks - was that an option when I ran the ufl. I've slept since I reflashed !!! Just to save me getting the leads out again etc :-/(Memory Man)
Just ran the ufl and I see upload/download Is that where I can upload from my box now? And save on my HD?
It*s good to talk
|
|
1shaddow1
Member
|
3. December 2008 @ 13:43 |
Link to this message
|
|
yes it is n looks like ur gettin ya leads out again :-)
|
Member
|
3. December 2008 @ 13:44 |
Link to this message
|
Originally posted by 1shaddow1:
yes it is n looks like ur gettin ya leads out again :-)
Gonna have to lash this webcam :-]
Thanks 4 gettin' back so quick
Cheers
It*s good to talk
|
|
Advertisement
|
|
|
|
Labraiz
Junior Member
|
3. December 2008 @ 13:57 |
Link to this message
|
hi i have the eurovox max blue i have just downloaded the new firmware v2.0 into it and now all it will do is switch on with nothing on the screen and 001 in the box window, the remote or buttons on the box wont do anyhthing only switch it on and off so now i am left with no channels,, can anybody help please,,,, i dont think my box is a clone one because i flashed it in april it was fine any suggestions please
|
