|
starview the box pvr
|
|
|
phaldred
Suspended due to non-functional email address
|
9. December 2008 @ 10:23 |
Link to this message
|
|
dinga id re-flash it just to be sure, if it first was in german its best to be 100% sure you have the right one!
|
|
Advertisement
|
|
|
|
|
smudger24
Member
|
9. December 2008 @ 11:43 |
Link to this message
|
I have installed the new firmware, but when I turn the box off then on again, I have to scan for channels again, like a first time install.
Any one else having this problem?
Any ideas how to solve it?
|
|
phaldred
Suspended due to non-functional email address
|
9. December 2008 @ 14:49 |
Link to this message
|
when you turn it on, and you get to the menu, just press exit on your remote, channels should still be there!
|
|
smudger24
Member
|
9. December 2008 @ 15:01 |
Link to this message
|
I have to select english, then press exit, and the channels return. Why does this happen? Does this happen for anyone else?
Not the end of the world, but never used to have to do this.
Any way round this?
|
AfterDawn Addict
|
9. December 2008 @ 15:03 |
Link to this message
|
Originally posted by smudger24:
I have to select english, then press exit, and the channels return. Why does this happen? Does this happen for anyone else?
Not the end of the world, but never used to have to do this.
Any way round this?
There are teething problems regarding this fix, they are being worked on, leave it alone for now and as soon as its rectified you will see it posted!!
|
|
smudger24
Member
|
9. December 2008 @ 15:11 |
Link to this message
|
|
Thanks, will wait patiently. Appreciate the hard work being put in.
(Could you post the link where any update will be posted so I can keep an eye on it please)?
|
AfterDawn Addict
|
9. December 2008 @ 15:13 |
Link to this message
|
Originally posted by smudger24:
Thanks, will wait patiently. Appreciate the hard work being put in.
(Could you post the link where any update will be posted so I can keep an eye on it please)?
you will see it here:
http://forums.afterdawn.com/thread_view.cfm/722659
|
|
sh4ff1
Newbie
|
10. December 2008 @ 06:18 |
Link to this message
|
|
hi can you help
i have the same box as dazlee and i have installed new r/w TheBoxPVR_v3105_08Dec2008.The system info shows it is there and every time i turn on box from standby it rescans, but i am still only getting the standard bbc itv etc. thanks
|
|
phaldred
Suspended due to non-functional email address
|
10. December 2008 @ 06:31 |
Link to this message
|
Originally posted by phaldred:
when you turn it on, and you get to the menu, just press exit on your remote, channels should still be there!
As for your channels, are there any other channels in the list (e.g the channels are there but just dont show?)
|
|
sh4ff1
Newbie
|
10. December 2008 @ 07:08 |
Link to this message
|
|
yes when it scans all the channels come up some in white and some in yellow. but only the standard ones play bbc1 bbc2 itv etc. no sky sports or any other cable channels
|
|
sh4ff1
Newbie
|
10. December 2008 @ 07:16 |
Link to this message
|
|
it does not auto update as before
|
|
phaldred
Suspended due to non-functional email address
|
10. December 2008 @ 07:23 |
Link to this message
|
|
when you go into the menu and system settings there is a option called keys(i think), that needs to be enabled, also go into the secret menu and check autoupdate is on.
|
|
malci
Suspended due to non-functional email address
|
10. December 2008 @ 07:28 |
Link to this message
|
Originally posted by sh4ff1:
it does not auto update as before
Have you turned it on? just give it a check to see, as below:-
If channels not clearing go to Menu / System Setup / Press OK with Parental Control highlighted then press i then 2007, this should put you in the CAS SYSTEM. (May need to do this a couple of times quite slowly to get into CAS SYSTEM)
With Nagravision 2 highlighted Press OK, On the Provider ID Line select your provider by using the left / right arrow buttons on remote then press OK, wait for it to save then press exit. (Your provider needs to be the same as the one you selected in Cable Network Option).
Finally make sure Autoupdate is On (Bottom Item in Cas System.) this may have changed in the fix, not to sure - Go to a scrambled channel and wait a while to clear.
|
|
malci
Suspended due to non-functional email address
|
10. December 2008 @ 07:30 |
Link to this message
|
Originally posted by phaldred:
when you go into the menu and system settings there is a option called keys(i think), that needs to be enabled, also go into the secret menu and check autoupdate is on.
Yep, I thought so - I am sure it has changed to keycode or similar.
|
|
sh4ff1
Newbie
|
10. December 2008 @ 07:37 |
Link to this message
|
|
Done that and all is working.thank you for your all your help:)
|
|
malci
Suspended due to non-functional email address
|
10. December 2008 @ 07:40 |
Link to this message
|
Originally posted by sh4ff1:
Done that and all is working.thank you for your all your help:)
Well done, glad your sorted,hope you didn't mind me coming in phaldred mate, just helping out. Good Luck ;)
|
|
phaldred
Suspended due to non-functional email address
|
10. December 2008 @ 07:46 |
Link to this message
|
|
not at all matey, your explanation was better than mine anyway :p i know when ive been beaten!
|
|
malci
Suspended due to non-functional email address
|
10. December 2008 @ 08:52 |
Link to this message
|
Originally posted by phaldred:
not at all matey, your explanation was better than mine anyway :p i know when ive been beaten!
Get away with you, it's not about that lol, only joking - cheers and take care, good luck ;)
|
|
smudger24
Member
|
10. December 2008 @ 09:01 |
Link to this message
|
Originally posted by smudger24:
I have installed the new firmware, but when I turn the box off then on again, I have to scan for channels again, like a first time install.
Any one else having this problem?
Any ideas how to solve it?
Any one else having this problem?
|
|
phaldred
Suspended due to non-functional email address
|
10. December 2008 @ 09:46 |
Link to this message
|
We all are having a simalar problem, however i dont have to rescan the channels, select english language, then when it goes to the main menu, press exit on your remote and your channels should still be there.
Its a bug in the firware, it'll be sorted asap.
|
|
sh4ff1
Newbie
|
10. December 2008 @ 19:23 |
Link to this message
|
many thanks u all have been a big help. Only problem i am havin now is that i switch my mains off in the night, the next day it has to be rescaned because when i press exit it goes back to language and i have to rescan i can not go on?
|
|
Advertisement
|
|
|
|
Liamo83
Junior Member
|
18. December 2008 @ 10:54 |
Link to this message
|
Hey,
I have tried to upload this new firmware (v3105_08Dec) but for some reason it wont work. I have unzipped the file and have it as a bin file. I am using PVR Loader v4.01sJul.11.2007 which came with the bin file but nothing seems to happen when I click download.
The download bar stays at 0% and the box reads b-31, any ideas??
|
