|
Eurovox max 2006 stuck on no1 after flashing new software
|
|
|
biscuit23
Junior Member
|
19. December 2008 @ 20:43 |
Link to this message
|
Hey all. I flashed my eurovox max 2006 blue box not a clone with the new software and now wont work. the remote switches the power on thats it wont change the channels only swithces the power on I think the new software doesnt work on the irish boxes. Then tried flash the old software that wont work.Hope its not broke. Any ideas people?
|
|
Advertisement
|
|
|
|
|
idc1966
Suspended due to non-functional email address
|
19. December 2008 @ 21:17 |
Link to this message
|
when you say that it wont work, and is stuck on 0001, do you have anything coming on your screen of the box, you may need to connect the box to your tv using an rf lead, not scart and tune it to your tv, either uhf freq 38 or 40, then you may see a message asking you to enter pin number, which is 1004, then ok, then you will get your menu up, then enable the scart output, do a complete power scan, and if it does not work after that, then you may need to put on the blue clonesafe firmware, i am not sure about the above, as it is something that i read on another forum, which is supposed to work. your remote maybe working, but if the scart is not enabled, and you cannot see an output from the box, you may not be able to do anything until the pin is entered.
|
|
biscuit23
Junior Member
|
20. December 2008 @ 07:46 |
Link to this message
|
|
pressed 1004 then lock light came up so thats something good in the right direction. cant find the station when scanning on the tv using rf cable. Put the scart back no joy either. when turn the box off it goes back to normal stte with no lights on other than the power light. Any other ideas?
|
|
idc1966
Suspended due to non-functional email address
|
20. December 2008 @ 13:20 |
Link to this message
|
did you make sure that you connected the rf cable to the rf out on the back of the eurovox, and not the cable output, then use your tv tuner to tune the box into the tv, if this does not work, then they may be other problems, as i said, i did read this as a solution on another forum, so cannot think of anything else offhand
|
|
biscuit23
Junior Member
|
20. December 2008 @ 15:02 |
Link to this message
|
|
ye did this still not working cheers for replying
|
|
popeye10
Member
|
21. December 2008 @ 06:03 |
Link to this message
|
bringing this back up.
i have also just flashed a box (eurovox 2006) with new blue firmware, plugged it all back in, powered on, then OSD displays 0001.
i can't change channels, get into the menu,or anything.
i have used the correct firmware, i know this because i flashed the same box 6-7 months ago. i know its not a T.V tuning issue too.
my guess is that it is just a bad flash, but i have reflashed it several times now and got the same result.
i am going to delete the firmware i have on computer, then download it again from eamos? then try flash again.
will report back.
anyone else had similar problems or know of a solution?
|
|
popeye10
Member
|
21. December 2008 @ 06:47 |
Link to this message
|
|
ok i re-downloaded UFL_MAX_BLUE_30_11_08
flashed again, came up as successful, connected it all back up and still same result.
help needed
|
|
BohsCelt
Newbie
|
21. December 2008 @ 07:32 |
Link to this message
|
|
i have the same problem aswell, thought it was the scart but have checked it on another tv. Just have a black screen and channel wont change.
Bohs-Celtic
|
|
biscuit23
Junior Member
|
21. December 2008 @ 10:19 |
Link to this message
|
I have the old software on my box at the min. Put new software on it same thing happened and then put the old software on back on. So dont know if it will work with the new but sure it will. Cn let us know? When u flash the box take scart out put an rf feed cable into the box and then have another rf cable coming out of the tv/vcr connection to the tv. Scan the tv and you will find a pin page of the box. Put 1004 in as the pin. Change the settings to rgb to use scart connection again. Have to put 1004 in as the pin every time turn the power off at the box.
|
|
idc1966
Suspended due to non-functional email address
|
21. December 2008 @ 20:36 |
Link to this message
|
once you have enabled the scart, it should stay that way until you alter the firmware again, after applying new firmware, certain boxes disable the scart output, so you need to manually tune the box back into the tv, enter pin, 1004 in this case, then change the settings back in the menu to re enable the scart, once reenabled, it will stay enabled until you either change the firmware, or disable it yourself, but after you power the box down, when you power up the box again, it will still be enabled.
|
|
popeye10
Member
|
23. December 2008 @ 09:40 |
Link to this message
|
ok so i put an RF lead into the tv/vcr socket on back of box and connected to the tv.
after tuning in the tv i got up the password box and entered 1004.
i still couldn't get into the menu (no reponse when press menu button on remote)
after a few seconds the eurovox powered off, came back on again then the password box on tv was all blurred.
have i done something wrong? i know someone posted to use the RF out socket, but it doesn't have one?
getting near my witts end with this one, more help please!!!!
|
|
idc1966
Suspended due to non-functional email address
|
23. December 2008 @ 10:02 |
Link to this message
|
|
on the back of the box, next to the power inlet socket, there is, or should be tv in, and tv out sockets, use the tv out socket, using rf patch lead to connect to telly, then tune in to tv, usally on 40 uhf, or 38 in some cases
|
|
popeye10
Member
|
23. December 2008 @ 10:22 |
Link to this message
|
|
next to power inlet is tv/vcr socket, and ant. socket.
on left of the box is rf in socket and loop out socket.
i guessed to use the tv/vcr socket... is that right?
|
|
BohsCelt
Newbie
|
23. December 2008 @ 11:29 |
Link to this message
|
|
i have the exact same problem as popeye
Bohs-Celtic
|
|
BohsCelt
Newbie
|
23. December 2008 @ 11:33 |
Link to this message
|
|
just to add i can get into the menu now but cant change to scart feed as its too hard t make out the writing
Bohs-Celtic
|
|
idc1966
Suspended due to non-functional email address
|
23. December 2008 @ 11:37 |
Link to this message
|
|
yes, where it says rf in on the box is for your cable input, and loop out is for your cable feed out , if you wish to run more boxes etc, where it says tv in and out is your normal loop for putting your aerial in, and connecting to tv, or vcr using the rf tuners.
|
|
popeye10
Member
|
24. December 2008 @ 08:54 |
Link to this message
|
Originally posted by popeye10:
ok so i put an RF lead into the tv/vcr socket on back of box and connected to the tv.
after tuning in the tv i got up the password box and entered 1004.
i still couldn't get into the menu (no reponse when press menu button on remote)
after a few seconds the eurovox powered off, came back on again then the password box on tv was all blurred.
have i done something wrong? i know someone posted to use the RF out socket, but it doesn't have one?
getting near my witts end with this one, more help please!!!!
back up
|
|
BohsCelt
Newbie
|
24. December 2008 @ 09:31 |
Link to this message
|
i'm just after loading the clone firmware on and can access the settings, i've done a factory reset and then went into powerscan and set the right settings for my area,i changed over to a scart lead aswell after the factory reset. hoping his works, will let you know.
Bohs-Celtic
|
|
BohsCelt
Newbie
|
24. December 2008 @ 09:37 |
Link to this message
|
|
it worked :)
Bohs-Celtic
|
|
popeye10
Member
|
24. December 2008 @ 10:01 |
Link to this message
|
good for you bohscelt.however.....
i'm a bit reluctant to try the clone firmware as i'm sure this is a genuine box, it belongs to a friend and i have flashed it in the past with the genuine firmware.
unless someone can assure me the clone firmware is safe to use?
|
AfterDawn Addict
2 product reviews
|
24. December 2008 @ 10:05 |
Link to this message
|
Originally posted by popeye10:
good for you bohscelt.however.....
i'm a bit reluctant to try the clone firmware as i'm sure this is a genuine box, it belongs to a friend and i have flashed it in the past with the genuine firmware.
unless someone can assure me the clone firmware is safe to use?
Check for yourself mate >> http://www.4shared.com/file/25134698/99e...e_Box_Pics.html
|
|
popeye10
Member
|
24. December 2008 @ 10:59 |
Link to this message
|
hi thanx hiteck, i do have that article, it is a genuine box, as i said, i have flashed it in the past with genuine firmware with success.
i am wondering if it's safe to use the clone firmware on it though?
|
|
Advertisement
|
|
|
|
hogie2008
Newbie
|
24. December 2008 @ 13:35 |
Link to this message
|
i have a eurovox TX on Ch***s, put new firmware on it and now its frozen on channel 02, remote wont work and cant get it out of this state? Whats happened? Please help.....
|
